Specifications - Lutron Electronics Hi-Lume Premier 0.1% Manual

LED Dimming Driver

Specifications

Regulatory Approvals and Compliance
• Lutron Quality Systems registered to ISO 9001.2008
• Manufacturing facilities employ ESD reduction
practices that comply with the requirements of
ANSI/ESD S20.20
• Meets ANSI C62.41 category A surge protection
standards up to and including 4 kV
• FCC Part 15 compliant for commercial applications at
120 V~ to 277 V~ and residential applications at 120 V~
• Meets UL 8750/CSA C22.2 No. 250.13-14, "Light Emitting
®
Diode (LED) Equipment For Use in Lighting Products"
• NOM certified
• Class 2 output; meets UL
Performance
• Dimming Range: 100% to 0.1%
• LED lighting turns on to any dimmed level without
flashing to full brightness
• Operating Voltage: 120 V~ to 277 V~ at 50 / 60 Hz
• R ated lifetime of 50,000 hours at 40 °C (104 °F)
ambient temperature and maximum loading
• For rated warranty, ambient temperature (t
exceed 40 °C (104 °F) (maximum rated temperature)
• Patented thermal fold back protection
• Non-volatile memory restores all driver settings after
power failure
• Typical standby power consumption: 0.25 W at
120 V~ and 0.4 W at 277 V~
• Open-circuit protected output
• Short-circuit and overload-protected output
• Output: 24 V- constant voltage at high-end
• Output Load Range: 2 W to 96 W at high-end
• PWM dimming frequency: meets IEEE1789 at all
dim levels
• Power Factor: > 0.90 at maximum power
• Total Harmonic Distortion (THD): < 20% at
maximum power
Light output at 0.1% depends on installation and light engine efficacy.
1
To maintain warranty, installer is responsible for ensuring that the driver ambient temperature does not exceed 40 ºC (104 ºF).
2
Where t is the temperature of the air directly surrounding the driver.
3
a
Additional considerations may be required based on state and local codes and standards.
4
S P E C I F I C AT I O N S U B M I T TA L
®
Job Name:
Job Number:
Hi-lume Premier 0.1% Constant Voltage Driver (L3D0)
1310/CSA C22.2 No. 223-M91
®
1
) not to
a
Model Numbers:
Performance
(continued)
• NEMA 410 – 2011 compliant
• Inrush Current Limiting Circuitry: decreases circuit
breaker tripping, switch arcing and relay failure; allows
full loading of switch leg
• Inrush Current: < 2 A
• Device turn-on time: < 100 ms from electronic off and,
< 500 ms from power off
• Meets all "Solid State Electrical Performance
Requirements" (Section 11) in Energy Star
Luminaires Version 2.0
• L3D0-96W24V-U driver is programmed by Lutron
manufacturing and is NOT configurable by the Lutron
QwikFig configuration system
Environmental
• Sound rated: Class A inaudible in 24 dBA ambient
• Relative Humidity: maximum 90% non-condensing
• Minimum Operating Ambient Temperature: t
• Indoor use only
• Rated for dry and damp locations
• Meets NEC requirements for installation in "other
®
2, 3
space used for environmental air"
• M eets the Canadian National Building Code Plenum
Requirements for a concealed space used as a
plenum within a floor or roof assembly
• Maximum heat output of module: 46 BTU/hour
Architectural Dimming
369883d 2 04.19.17
for
®
= 0 °C (32 °F)
3
a
4
Page
2