Makita 9565CR Instruction Manual
Hide thumbs
Also See for 9565CR:
- Instruction manual (132 pages) ,
- Technical information (9 pages) ,
- Instruction manual (100 pages)
Related Manuals for Makita 9565CR
Summary of Contents for Makita 9565CR
- Page 1 INSTRUCTION MANUAL Angle Grinder 9565CR 9565CVR DOUBLE INSULATION Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model 9565CR 9565CVR Wheel diameter 125 mm 125 mm Max. wheel thickness 7.2 mm 7.2 mm Spindle thread Rated speed (n) / No load speed (n 12,000 min 12,000 min Overall length 299 mm 299 mm Net weight 2.4 kg 2.4 kg... - Page 3 Save all warnings and instruc- 15. Do not overreach. Keep proper footing and balance at all times. This enables better control tions for future reference. of the power tool in unexpected situations. The term "power tool" in the warnings refers to your 16.
- Page 4 Operations such as polishing are not rec- 13. Do not run the power tool while carrying it at your ommended to be performed with this power side. Accidental contact with the spinning accessory could tool. Operations for which the power tool was not snag your clothing, pulling the accessory into your body.
- Page 5 d) Wheels must be used only for recommended Additional Safety Warnings: applications. For example: do not grind with the 17. When using depressed centre grinding wheels, side of cut-off wheel. Abrasive cut-off wheels are be sure to use only fiberglass-reinforced intended for peripheral grinding, side forces applied wheels.
-
Page 6: Functional Description
Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock ► 1. Indication lamp (speed adjusting dial) For Model 9565CR ► 1. Shaft lock CAUTION: • Never actuate the shaft lock when the spindle is moving. - Page 7 Speed adjusting dial Installing side grip (handle) For Model 9565CVR CAUTION: ► 1. Speed adjusting dial • Always be sure that the side grip is installed The rotating speed can be changed by turning the speed securely before operation. adjusting dial to a given number setting from 1 to 5. Screw the side grip securely on the position of the tool Higher speed is obtained when the dial is turned in the as shown in the figure.
- Page 8 For tool with clamp lever type wheel Mount the inner flange onto the spindle. Fit the wheel/ disc on the inner flange and screw the lock nut onto the guard spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.
-
Page 9: Operation
Installing or removing dust cover attachment (Optional accessory) WARNING: • Always be sure that the tool is switched off and unplugged before installing or removing the dust cover attachment. Failure to do so causes dam- age to the tool or a personal injury. There are three types of dust cover attachment and each is used in one of different positions. - Page 10 Grinding and sanding operation Operation with abrasive cut-off / diamond wheel ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and Optional accessory then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an WARNING: When using an abrasive cut-off...
-
Page 11: Optional Accessories
• These accessories or attachments are recom- mm (5/32")) 3. Abrasive cut-off wheel (4 mm (5/32") mended for use with your Makita tool specified or thicker) 4. Inner flange in this manual. The use of any other accessories or attachments might present a risk of injury to When installing the diamond wheel: persons. - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884863H226 www.makita.com 20180822...