Barthelme CHROMOFLEX Pro Series Instruction Manual page 5

ENGLISH
Instruction manual for
Please read this manual carefully and keep it in a save place!
Item no. 66000025 remote control (for use with
66000045
1. Introduction
®
CHROMOFLEX Pro is an advancement of
4 channels (for modern R-G-B-W LEDs - Art. 66000034) and is totally radio controlled.
For control and settings either
USB dongle (for PC/Art. 66000036) are necessary.
®
CHROMOFLEX Pro
can be attained even without programming. The unit is equipped with various colour effects by default such as:
colours, calming colour changes, even show effects. Some of them can be edited or set as standard effect by
radio control.
Several CHROMOFLEX
effects) are in sync within the network automatically. Therefore sophisticated illuminations can be attained with a
minimum of effort. Operating range depends on room conditions. Operation of up to 300 metres should be possible
outdoors. Indoors an operating range of 20- 50 metres should be unproblematic.
2. Usage
Colours and effects of the
be stored on the CHROMOFLEX
as start program. For operation the remote control is equipped with solid-state touch keys / slider.
®
CHROMOFLEX Pro
and Iceland).
3. Technical data
Operating voltage: 3V DC
Batteries: 1 * 3V button cell CR2032
Protection class: III
Measures (L/W/H): 104 / 67 / 28mm
Ambient temperature: 0°C - max. +50°C (in dry conditions only, non-condensing)
Radio frequency: 868.3MHz (licence-free in EC, Switzerland, Norway and Iceland).
Manufacturer: Josef Barthelme GmbH & Co. KG
4. Safety instructions
The unit is equipped with a built-in protection against reverse polarity. Connecting the power in reverse polarity
can destroy the module, even if connected for a short time only.
Please remove and replace empty batteries because they could leak.
We decline any liability, loss or damage caused by improperly used modules! Guarantee is also lost in such cases.
This product is not a toy, keep away from children!
5. Operation
Please operate this unit only when it is working properly.
In case of an error, switch off the unit immediately. Do not operate the unit, until the unit was verified electronically
by a qualified electrician.
A case of error is:
- Visible signs of damage on the unit
- The unit is not operating properly
- fume rising or crackling sounds from the unit
- Visible signs of overheating
5.1 Start-up
Please insert 3V button cell into the remote control. Loosen, the screws on the back of the remote control. Please
insert the batteries with correct polarity, because otherwise the remote control may be damaged (guarantee is
lost in such a case). Close housing again. The red LED on the right side will flicker for about 15 minutes every 5
seconds. After about 15 minutes, the remote control automatically switches to power saving mode, which when
pressing any key. To program the remote control using the "ProCEd" software, the unit must be in normal mode,
not in power saving mode.
V1.1 / 12.01.2015
CHROMOFLEX
66000043, 66000044, 66000343, 66000344)
CHROMOFLEX
®
CHROMOFLEX
was designed so that sophisticated illuminations in the field of decoration and wellness
®
Pro can be linked in a network, whereas all colour changes/scenes (except. random
®
CHROMOFLEX Pro
®
Pro . After reconnecting the supply voltage, the desired colour or effect is set
series operates on a frequency of 868.3 MHz (licence-free in EU, Switzerland, Norway
®
®
CHROMOFLEX Pro/Pro File
®
I, II and RC. The PRO version consists of up to
Pro remote control (Art. 66000045) or
can be controlled by remote control. Settings being made can
5 / 8
Pro Series
units 66000033, 66000034,
CHROMOFLEX
®
CHROMOFLEX
®
Pro
Pro Remote