Advertisement
150 Watt
Tungsten Halogen
Light Source
CSA Listed to UL-1571
LIGHT SOURCE MODELS
SOLID STATE RHEOSTAT
SOLID STATE RHEOSTAT
AND IRIS DIAPHRAGM
122 Charlton Street, Southbridge, MA 01550-1960
115 VAC/60Hz
A20500
EKE Lamp
A20500.1
EJA Lamp
A20500.2
DDL Lamp
A20520
EKE Lamp
A20520.1
EJA Lamp
A20520.2
DDL Lamp
Owner's Manual
230 VAC/50Hz/60Hz
A20510
A20510.1
A20510.2
A20530
A20530.1
A20530.2
EKE Lamp
EJA Lamp
DDL Lamp
EKE Lamp
EJA Lamp
DDL Lamp
Advertisement
Table of Contents
Related Manuals for SCHOTT ACE Series
Summary of Contents for SCHOTT ACE Series
- Page 1 Owner’s Manual 150 Watt Tungsten Halogen Light Source CSA Listed to UL-1571 LIGHT SOURCE MODELS 115 VAC/60Hz 230 VAC/50Hz/60Hz A20500 EKE Lamp A20510 EKE Lamp SOLID STATE RHEOSTAT A20500.1 EJA Lamp A20510.1 EJA Lamp A20500.2 DDL Lamp A20510.2 DDL Lamp A20520 EKE Lamp A20530...
- Page 2 Phone: (508) 765-9744, Fax: (508) 765-1299 Email: lightingimaging@us.schott.com www.us.schott.com/lightingimaging...
-
Page 3: Maintenance
CONGRATULATIONS on the purchase of your “ACE” light source! This light source provides COOL, INTENSE WHITE light for all types of fiber optic illumination components and either meets or exceeds the performance standards of all the safety certification agencies like UL, ETL, CSA, and VDE. - Page 4 cause burns. Operators are advised to allow the unit to cool before opening or relamping “Modulamp” assembly.
-
Page 5: Operation
OPERATION To begin, make sure the intensity control switch on the front panel is in the “OFF” position. Plug one end of the power cord into the IEC connector on the back of the unit and the other end into a power source which meets the specifications printed above the IEC connector. -
Page 6: Funzionamento
FUNCIONAMIENTO Interruptor apagado. Enchufar en el conectador IEC. Enchufar en un enchufe conforme a las especificaciones encima del conectador IEC. Apretar el tornillo en el aparato “Modulámpara”. Insertar la parte constituliva fibra-óptica compatible en el ajustador del origen de luz. Apretar el tornillo que retiene la fibra-óptica. -
Page 7: Lamp Replacement
LAMP REPLACEMENT • Turn power off. • Remove the fiber optic component. • Allow the lamp to cool. • Loosen the “Modulamp” captive thumbscrew until the head springs forward. • Pull the top of the “Modulamp” assembly forward and lift the unit out of the recess. CAUTION: LAMP, LAMP SOCKET AND SURROUNDING SURFACES MAY BE HOT! Do not pull the Assembly beyond the length of the cable and connector assembly. - Page 8 settings may be changed by moving the lamp holder into the correct position. Consult the factory for correct lamp locations.
-
Page 9: Remplacement De La Lampe
REMPLACEMENT DE LA LAMPE 1 Mettre l’interrupteur sur position “off”. 2 Retirer le conducteur fibre optique. 3 Laisser la lampe refroidir. 4 Dévisser le module lampe avec un petit tournevis jusqu’à ce que la tête ”s’éjecte par devant” 5 Tirer l’ensemble du module lampe et l’enlever de son logement. Ne pas tirer l’ensemble plus loin que la longueur de câble. - Page 10 Tirare la parte superiore della modulampada e sollevaria dal recesso. NON rimuovere il montaggio oltre la lunghezza del cavo. Abbassare il dispositivo di sgancio del portalampada per rimuovere la lampadina. Delicatamente staccare il portalampada in ceramica. Inserire la nuova lampadina nel portalampada. NON toccare il bulbo o l’interno del riflettore.
-
Page 11: Safety Instructions
WARNING • • Never look directly at lamp when on. • Modulamp” assembly must be firmly in place to operate • Lamp and surrounding surfaces may be hot! • ATTENTION • Ne pas regarder directement la lampe quand elle fonctionne. •... -
Page 12: Troubleshooting
DO NOT OPEN THIS UNIT. There are no user serviceable parts inside. The unit should be serviced ONLY by SCHOTT authorized service personnel if it does not operate normally or exhibits any marked change in performance; or if the power cord or enclosure has been damaged;... - Page 13 SPECIFICATIONS PHYSICAL: ELECTRICAL: Overall dimensions Input Voltage Height: 4.62" (177 mm) 115VAC/60Hz (Models A20500 & A20520) Width: 7.27" (185 mm) 230VAC/50Hz (Models A20510 & A20530) Depth: 8.61" (219 mm) Weight: 9 pounds Output 21VAC Fiber Receptacle .720" diameter (18.3 mm) Power Consumption 190 Watts (nominal) Environmental Operating...
-
Page 19: Service Policy
LIABILITIES Any warranty implied under State Law shall be limited to one year from original delivery to original purchaser. Specifically excluded from the manufacturer liability is damage resulting from acts of any deity, malicious mischief, vandalism, riots, wars, improper installation or neglect in the operation or maintenance of the unit or misunderstanding of the properties of the unit.