Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ORiNOCO AP-9000R
Summary of Contents for ORiNOCO AP-9000R
- Page 1 ® ORiNOCO AP-9200R (Outdoor Access Point) Hardware Installation Guide...
- Page 2 Proxim Wireless Corporation. Trademarks ® ® ORiNOCO , Proxim , and the Proxim logo are the trademarks of Proxim Wireless Corporation. All other trademarks mentioned herein are the property of their respective owners. Disclaimer Proxim reserves the right to revise this publication and to make changes in content from time-to-time without obligation on the part of Proxim to provide notification of such revision or change.
-
Page 3: Table Of Contents
ORiNOCO® AP-9200R Hardware Overview ........ - Page 4 D Safety & Regulatory Information ..........65 ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 5: Package Contents
WD - US and EU power cords US - US power cord 2.4 GHz, 7 dBi Omni Antennas (x 3) 5 GHz, 7 dBi Omni Antennas (x 4) Connector Weather Proofing Kit (1 set) Grounding Kit ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 6 Package Contents What’s in the kit Image Mounting Kit and Hardware The mounting kit includes the following: Full axis mounting kit Quick Installation Guide ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 7: Getting Started
It is mandatory to check the Safety & Regulatory Information before you perform the Installation procedure. You will need the following tools to perform the Installation: 10mm Spanner #2 Philips Screw Driver #3 Philips Screw Driver Crimping Tool ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 8: Device Overview
Device Overview This section provides the hardware overview and installation procedure for the following product(s): • AP-9200R ® 3.1 ORiNOCO AP-9200R Hardware Overview Device Model Description ® AP-9200R ORiNOCO AP-9200R, MU-MIMO 4x4 w2, dual radio, connectorized outdoor Access Point Figure 3-1 AP9200R The features of the above devices are tabulated as below: A detailed description about the various components of the device are explained in the following sections. -
Page 9: Gigabit Ethernet Ports
(M4 thread size) provided to attach a ground wire of at least 12 AWG stranded to the device. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 10: Device Installation
Safety & Regulatory Information. The devices are designed to directly mount to a pole. By using the supplied brackets and hardware, you can mount them to a 1.5 to 3.25 inch pole (outside diameter). ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 11 10. Warp Butyl Mastic Tape and Vinyl Tape around the connectors to weatherproof the RP-SMA and antenna connections. Figure 4-1 Weatherproofing RJ45 Connection Additional Weatherproofing Steps To add an additional layer of protection to the connectors against the environment, see Additional Weatherproofing Steps. ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 12 3. Tighten the nut slightly so that the U-bolt is adjustable for pole mounting. After adjusting the angle of the device, fully tighten the nut. Figure 4-3 Pole Mounting Step 8: Plug in the Cables ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 13 Step 10: Install Surge Protector ® ORiNOCO AP-9200R Series products comes with a built-in Ethernet surge protection; however, it is mandatory to install an approved lightning surge protector at the building ingress point. Moreover, if you are installing the device in a region subjected to violent thunderstorms or severe weather conditions, then installation of an additional approved lightning surge protector near the device is recommended.
- Page 14 7. Make sure all connections are fastened securely and tight. 8. Never install a link during a storm and always follow your local safety codes. Connect the grounding wire, which is supplied with the product package, to the device as shown below: ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 15 Figure 4-7 Port LED Indicators LED State Status LED Ethernet link is down Ethernet link is active Gigabit LED Ethernet link is established at Ethernet link is established at 1 Gbps 100 Mbps ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 16: Technical Specifications
Device Models Model Part Description Number ® AP-9200R-US 903-00035 ORiNOCO AP-9200R, MU-MIMO 4x4 w2, dual radio, connectorized outdoor Access Point – US Power ® AP-9200R-WD 903-00036 ORiNOCO AP-9200R, MU-MIMO 4x4 w2, dual radio, connectorized outdoor Access Point – WD Power ®... -
Page 17: Ofdm Modulation Rates
75m outdoor, RJ45 terminated, UV Rated, STP Shielded CAT5e cable with M20 and M25 cable gland 949-00154 ETH-CAP-M25-25 Cable Feed Thru, M25 Cable Gland Connector for Edge and ORiNOCO® 9200R - 25 pack 949-00155 1000-UMK Outdoor Universal Mounting Kit for Edge and ORiNOCO® 9200R... -
Page 18: Wireless Protocol
Wireless Protocol Radio #1: 802.11a/n/ac Radio #2: 802.11b/g/n Interfaces Products Category Specification AP-9200R Wired Ethernet Auto MDI-X, auto configuration fixed speed/duplex configurations. One auto MDI-X RJ45 Gigabit Ethernet Port with PoE IN and Data. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 19: Transmit Power Specifications (5.150 To 5.850) Ghz
In the FCC United States 5.8 GHz band edge frequencies, the Maximum Tx Power of the radio will be restricted based on the FCC Certification and Antenna Type used. For details refer the Antenna Intallation and Recommendation Guide. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 20: Transmit Power Specifications (2.400 To 2.484) Ghz
VHT80 BPSK Dual Stream AP-9200R QPSK QPSK 16 QAM 16 QAM 64 QAM 64 QAM 64 QAM 256QAM 256QAM Note: • Receive Sensitivity values should be considered with a tolerance +/- 2 dB. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 21: Receive Sensitivity (2.400 To 2.484) Ghz
64 QAM MCS 15 64 QAM Note: Receive Sensitivity values should be considered with a tolerance +/- 2 dB. 2.400 - 2.484 GHz Products Stream Data Rate (Mbps) Receive Sensitivity (dBm) AP-9200R Single Stream ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 22: Power Supply
Products Operating Temperature Storage Temperature Humidity Wind Loading AP-9200R -30º to 55º Celsius -50º to 70º Celsius 100% relative humidity 180 km/h -22º to 131º Fahrenheit -58º to 158º Fahrenheit IP67 112.5 mph ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 23: Mtbf
Technical Specifications MTBF Products MTBF AP-9200R >250,000 hours ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 24: Recommended Antennas
(for example, connecting two buildings in an office park or campus). Sector antennas produce hemispherical coverage, spreading away from the mount point to a width of 30 to 180 degrees typically. The figure below depicts the radiation pattern for the sector antenna. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 25: Supplied Antenna Specifications
5 GHz Omni Antenna 2.4 GHz Omni Antenna Connector RP-SMA plug RP-SMA plug Size 250xØ16 mm 250xØ16 mm Operating Temperature -40°C ~ +80°C -40°C ~ +80°C Storage Temperature -40°C ~ +80°C -40°C ~ +80°C ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 26 Recommended Antennas 5 GHz Omni Antenna ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 27 Recommended Antennas 2.4 GHz Omni Antenna ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 28: Recommended Antennas
Recommended Antennas 7.4 Recommended Antennas ® : Tabulated below are the antennas that Proxim recommends you to use with the ORiNOCO AP-9200R Series devices. To buy these antennas, place an order separately with your distributor. Dual - Polarized Antennas Product(s) -
Page 29: Dbi Dual Polarized Sector Antenna
Water Tightness IP67 Dimension (L x W x H) 500 x 200 x 30 mm Weight 1.5 kg (max) Connectors 2 x N-type female Radome Material Plastic Radome Thickness 2.0 ± 0.2 mm ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 30 Recommended Antennas ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 31: Dbi Dual Polarized Sector Antenna
Water Tightness IP67 Dimension (L x W x H) 500 x 200 x 30 mm Weight 1.5 kg (max) Connectors 2 x N-type female Radome Material Plastic Radome Thickness 2.0 ± 0.2 mm ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 32 Recommended Antennas ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 33: Panel Antenna Specifications
Dimension (L x W x H) 370 x 370 x 40 mm Weight 2.1 kg Connectors 2 x N-type female Radome Material UV Protected Poly carbonate Back Plane Aluminum protected through chemical passivation ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 34 Recommended Antennas Antenna Patterns ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 35: Dbi Dual Polarized Panel Antenna
Dimension (L x W x H) 600 x 600 x 22 mm Weight 4.7 kg Connectors 2 x N-type female Radome Material UV Protected Poly carbonate Back Plane Aluminum protected through chemical passivation ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 36 Recommended Antennas Antenna Patterns ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 37: Dbi Quad Polarized Panel Antenna
Operating Temperature Range -55°C to +65°C Vibration According to IEC 60721-3-4 Wind Load 200 Km/h (Survival) Flammability UL94 Water Proofing IP-67 Humidity ETS 300 019-1-4,EN 302 085 (Annex A.1.1) Salt Fog According to IEC 68-2-11 ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 38 Recommended Antennas Antenna Patterns ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 39 Recommended Antennas ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 40: Antenna Installation
5. Verify that the device, support structure for antenna (antenna-mast) and entire cable set-up for the antenna are Connecting the Cables. connected properly. See Connecting the Antenna Cable. 6. Connect the antenna cable to the antenna. See ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 41: Required Materials
Ensure that you have acquired all the materials listed above, to begin with the outdoor antenna installation. Refer to the Quick Installation Guide, that comes along with your product, for details on mounting the outdoor equipment. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 42: Determining The Optimal Antenna Placement
Clearance Factor: It is required for optimal performance (See of the antennas leave sufficient clearance of the Fresnel Zone at the maximum width of the bulge, which is typically at the mid-point between the antennas. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 43: Mounting The Antenna
30 degrees, the maximum EIRP limit should be set to 125 mW (21 dBm). The compliance can be achieved through proper selection of antenna, angle of elevation, and Tx power control to provide reasonable protection from harmful interference to users, authorized devices, and co-channel NGSO/MSS operations. ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 44 The calculation of Transmit Power to comply with the EIRP limits for an antenna with a gain of 22 dB is explained below for three different tilt angles: • Case 1: 0 = 0 (No antenna tilt) ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 45 = 21 - 5 = 16 dBm • Case 2: 0 = 15 (antenna tilted upward) – The antenna gain for 0 = 15 is shown in the following figure: Figure 8-5 Antenna gain at (30- 0) = 15 ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 46 -10 degree indicates that the antenna is tilted downwards. • 10 degrees indicates that the antenna is titled upwards. Tilt Angle Allowed Transmit Power per EIRP of Product Remarks (degrees) Single chain (dBm) (dBm) Not Recommended ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 47: Connecting The Cables
3. Secure the antenna cable to the antenna mast, as the cable connectors do not support the full weight of the cable. 4. Connect the other end of the antenna cable to the device. : Do not use tools to tighten the cable connectors, as they damage the antenna cable and connectors. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 48: Connecting The Surge Arrestor And Ethernet / Power Cables
: It is mandatory to install an approved lightening surge protector at the building ingress point. If the device is installed in a region subjected to violent thunderstorms or severe weather conditions, then installation of an additional ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 49: Grounding The System
We have used the following Butyl Mastic Tape and Vinyl Tape as an example to demonstrate the weatherproofing steps: 2. Follow the following weatherproofing steps: : We have taken MP-1xxx-BSU and external antenna as an example to explain the weatherproofing ® steps. Follow the same method to weatherproof the antenna connectors of the ORiNOCO products. ® ORiNOCO... - Page 50 Weatherproofing at the antenna end: Step 2: Wrap a second layer of vinyl tape in the reverse direction over the first layer of tape. a. Weatherproofing at the device end: b. Weatherproofing at the antenna end: ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 51 Step 4: Next, wrap a layer of the butyl mastic tape over the adhesive side of the tape, covering all of the tape and connector. a. Weatherproofing antenna connectors on the device: b. Weatherproofing antenna cable: Step 5: Wrap vinyl tape over the butyl layer and cover the entire tape assembly. ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 52 Weatherproofing antenna cable: Step 6: Place a small zip tie over the last wrap of tape to prevent it from unwrapping over time. The figure below depicts the complete weatherproofing of the RF connection. ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 53: Measuring Signal Performance
Weather conditions (rain or snow) usually do not have much impact on the performance of your device, provided you have sealed all the cable connectors with weatherproofing tape. Seasonal influence on signal propagation can occur in the following situations: ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 54: Fresnel Zone Calculation
Then, Path Difference (d3) and Fresnel Radius (r , radius of the n Fresnel Zone) can be calculated from the formula below: (where n = 1, for the first Fresnel Zone and r ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 55: Clearance Factor
To determine the effect of insufficient signal path clearance, you must determine the Clearance Factor and also calculate its Determining the Range. effect on the range for your antenna installation, by using the formula described in ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 56: Calculations
(say, 99.999% or 5.3 minutes of predicted outage per year). 9.5.1 Calculating Link Budget Use the following formula to estimate the received signal level (RSL): RSL (dBm) = P ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 57 The following figure is a pictorial representation of the elements in the Link Budget equation. Figure 9-4 Link Budget Equation-Pictorial Representation ® ORiNOCO AP-9200R - Hardware Installation Guide...
- Page 58 Received Signal Level (RSL). ® 6. For details on the receive sensitivity and data rate values used for the wireless link, for details refer to ORiNOCO AP-9200R Hardware Installation Guide. 7. Subtract this value from the Received Signal Level; this is the Fade Margin.
- Page 59 An EIRP limit is the maximum RF energy that can be transmitted as measured at the transmitting antenna and is usually deterwmined by government regulations. FCC United States 5.8GHz band power limit for band edge frequencies ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 60: A Lightning Protection
The surge arrestor (sometimes referred to as a lightning protector) can protect your sensitive electronic equipment from high-voltage surges caused by discharges and transients at the PoE. ® Proxim Wireless offers superior lightning and surge protection for ORiNOCO AP-9200R Series products. Contact your reseller or distributor for more information. -
Page 61: B Abbreviations
Power Over Ethernet PTMP Point-to-multipoint Point-to-point Quick Installation Guide RSSI Received Signal Strength Indicator Receiver Shielded Twisted Pair Subscriber Unit Transmission Control Protocol Transmission User Diagram Protocol Unshielded Twisted Pair WORP Wireless Outdoor Router Protocol ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 62: C Warranty And Technical Support
Case Management: Login to check the status of your support cases, update your personal profile, or access restricted information and features. • Provide Feedback: Submit a suggestion, complaint, or other feedback about the support site and our products. ® ORiNOCO AP-9200R - Hardware Installation Guide... -
Page 63: Additional Information On Servpak Options
Hardware is shipped on business days, Monday – Friday excluding Holidays, 8:00 AM – 3:30 PM Eastern Time. 7x24x365 Availability Unlimited, direct access to technical support engineers 24 hours a day, 7 days a week, 365 days a year including Holidays. ® ORiNOCO AP-9200R - Hardware Installation Guide... - Page 64 To purchase ServPak support services, please contact your authorized Proxim distributor. To receive more information or for questions available ServPak support options, please visit website http://www.proxim.com/support/servpak, call Proxim Support (For telephone numbers, see Telephone Support) or send an email to servpak@proxim.com. ® ORiNOCO AP-9200R - Hardware Installation Guide...
-
Page 65: D Safety & Regulatory Information
Safety & Regulatory Information ® For Safety & Regulatory Information, please refer Safety and Regulatory guide for ORiNOCO AP-9200R Series. To download the Safety and Regulatory Guide, visit http://support.proxim.com. ® ORiNOCO AP-9200R - Hardware Installation Guide...