Table of Contents
Advertisement
Quick Links
uincy
ab
SPECIFICATIONS
INTERIOR DIMENSIONS
INCHES W x H x D
(CM) W x H x D
EXTERIOR DIMENSIONS
INCHES W x H x D
(CM) W x H x D
TEMPERATURE RANGE
CONTROL STABILITY
@ 100C
@ 200C
STANDARD ELECTRICAL
VOLTS/AMPS
PLUG/NEMA
WEIGHT
SHIPPING
STAND ALONE
Common Unit Construc�on
Exterior:
Insula�on:
Thermo-control:
Issue Rev A 0320
Copyright Quincy Lab Inc. 2020
Bench Series Ovens Operating Manual
MODEL
21-250ER
25.5x19.7x24
64x49.5x60
33x24x35.5
83x60x90
300 F/150 C
o
+/- 0.2
C
NA
120/8.75*
WATTS
1050
5-15P*
*
Standard models voltage only, optional 230 voltage available. Check label on back of unit.
185
165
Powder Coated Steel
Fiberglass
Hydraulic
Quincy Lab Inc. 1925 N. Leamington Ave. Chicago, Illinois
ER Models 21 /31 /51
Quincy Lab, Inc.
*
Verify
o
C or
o
F units
*
Increase Setpoint
*
Decrease Setpoint
(3 sec.) Enter/Exit
(PRESS)
Menu Levels
PROGRAMMABLE CONTROL
MODEL
MODEL
21-350ER
31-250ER
25.5x19.7x24
25.5x29.7x24
64x49.5x60
64x75.5x60
33x24x35.5
33x34x35.5
83x60x90
83x86x90
450 F/232 C
300°F/150°C
o
o
+/- 0.5
+/- 0.3
C
o
o
+/- 0.5
+/- 0.5
C
120/16*
120/16*
1920
1920
5-20P*
5-15P*
185
225
165
200
Interior:
Aluminized Steel (SS op�onal)
Motor:
Sealed Ball Bearing
Heater:
Resis�ve - Tubular Incoloy
Standard Contents
(1) Bench ER Series Oven
(2) Adjustable chrome wire shelf
(4) Shelf brackets
Approvals:
Underwriter's UL / CUL, United States/
Canadian for laboratory equipment.
Compliance: UL Standard 61010-1
IEC 61010-1.
NOT FOR USE WITH FLAMMABLE
LIQUIDS OR GASES
MODEL
31-350ER
25.5x29.7x24
25.5x19.7x22.5
64x75.5x60
33x34x35.5
83x86x90
450 F/232 C
550 F/287 C
o
C
+/- 0.5
C
o
C
+/- 0.5
C
120/16*
1920
5-20P*
225
200
1800-482-4328
MODEL
51-550ER
64x49.5x57
33x24x35.5
83x60x90
o
+/- 0.5
C
o
+/- 0.5
C
230/12.5
2850
6-20P
195
170
PAGE 1
Advertisement
Table of Contents
Related Manuals for Quincy lab Bench ER Series
Summary of Contents for Quincy lab Bench ER Series
- Page 1 Powder Coated Steel Interior: Aluminized Steel (SS op�onal) Insula�on: Fiberglass Motor: Sealed Ball Bearing Thermo-control: Heater: Hydraulic Resis�ve - Tubular Incoloy Issue Rev A 0320 Quincy Lab Inc. 1925 N. Leamington Ave. Chicago, Illinois 1800-482-4328 Copyright Quincy Lab Inc. 2020 PAGE 1...
-
Page 2: Setup And Installation
WARNING IMPORTANT WARNING Refers to an important note in the usage of the unit. Warns of a possible electrical shock Warns of a possible risk of fire CAUTION WARNING Cautions of HOT exterior surface during operation. Warns of possible injury or muscle strains, use assistance when moving or liftiing. Safety Precautions Read Operating Instructions Thoroughly Prior to Operation Read Operating Instructions thoroughly prior to operation and observe the following safety precautions:... -
Page 3: General Operation
DIGITAL MICROPROCESSOR ADJUSTING CONTROLLER’S SETPOINT TEMPERATURE Temperature Controller Upon start-up all Quincy Lab Bench Ovens will display the current chamaber temperature (green LEDs) and begin the heating process to the factory default temperature set-point (orange LEDs) which varies depending on your oven’s model. - Page 4 General Operation (continued) Pressing the star key alone verifies the control's temperature display units in degrees F or C (factory set at "°F" for Fahrenheit). To change the display units to read in Centigrade, see the control's Menu Level Functions on page 6. The temperature setting is maintained in the control whenever the power is turned off.
-
Page 5: Clearance Requirements
Safety Alarm Reset THERMO SAFETY ALARM REMOVE SNAP DISC HOLE The unit incorporates a thermo safety shut-off. In the event of electron- PLUG TO ACCESS SAFETY ic failure, an internal “snap disc” will cut off power to the unit until it is REST DISC BUTTON. - Page 6 Menu Level Functions Access the menu levels for the following functions: FUNCTION PROMPT Change control to read in C or F temperature units ( in level 2). UNIT Change to whole degree or 1/10th degree display resolution ( in level 2). DISP Run or Read temperature tracking /data ( in level 3).
- Page 7 Temperature Tracking Feature This feature monitors the stability of the control during any given length process. It will record and display the following: The total variation or spread between high and low temperature. The absolute or maximum high temperature The absolute or minimum low temperature How to start the tracking feature Navigate on the controller to "CheK"...
-
Page 8: Technical Support
Chicago, Illinois 60639 Limited Warranty Quincy Lab, Inc. warrants to the original purchaser that this product will be free from defects in material and workmanship under normal use throughout the warranty period. The standard warranty period for this instrument is instrument is eighteen months from date of shipment. The instrument warranty is supplemented with a three year warranty on the heating element.