Maintenance Schedule; Headset; Brakes - Orbea RISE M-LTD 2021 Technical Manual

12 | ORBEA
TIGHTENING TORQUES. Always check the
tightening torques and install the compo-
nents described in this manual according
ponents from other manufacturers installed on
your Orbea bicycle. The failure to follow these
the components, accidents and even death.
M AINT ENANCE SCH EDU LE
OF THE COMP ONEN TS
Maintenance periods for the components
indicated below are general guidelines and
largely depend on factors such as weather
conditions in which your bicycle is ridden (ad-
verse conditions considerably reduce the life
of the components and increase maintenance
frequency), the cleanliness of your bicycle and
its components (components with accumulat-
ed dirt wear more quickly), and use (more de-
manding use of the bicycle will require more
frequent maintenance periods).
For components from other brands mounted
on Orbea bicycles, you can check the recom-
mended or mandatory maintenance periods
on the manufacturer's website or by contacting
the distributor of that brand in your country.
Damage to components as a result of failing
to follow the recommended maintenance
periods could result in damage that is not
covered by the warranty conditions of Orbea
or the component manufacturer.
The failure to comply with maintenance peri-
ods could result in damage to the components
and lead to malfunctions and accidents.
TECHNICAL MANUAL

HEADSET:

· Inspection of its operation before each ride.
· Disassembly and manual inspection of the bearings once
every 6 months of use.
-
BOTTOM BRACKET:
· Inspection of its operation before each ride.
· Disassembly and manual inspection of the bearings once
every 6 months of use.
DRIVETRAIN:
· Inspection of its operation before each ride.
· Regular inspection of chain wear every 500 km. A chain
that is worn beyond the manufacturer's recommendations
must be replaced to prevent damage to the rest of the driv-
etrain components. The failure to observe the manufactur-
er's recommendations in terms of wear could necessitate
the replacement of the rest of the parts of the drivetrain.
WHEELS:
· Inspection of its operation before each ride.
· Disassembly and manual inspection of the bearings and
all components once every 6 months.
SHOCKS AND SUSPENSION FORKS:
· Inspection of its operation before each ride.
· Inspection and full maintenance every 125 hours or once
authorized dealer.
TELESCOPIC SEAT POSTS:
· Inspection of its operation before each ride.
· Inspection and full maintenance every 125 hours or once
authorized dealer.
PIVOT POINTS ON FULL SUSPENSION FRAMES:
· Inspection of its operation before each ride.
· Disassembly of the frame and the manual inspection of
all the bearings every 125 hours of use or once a year
pending on the conditions in which the bicycle is ridden.
More demanding use of the bicycle or use in adverse
weather conditions or in mud requires the disassembly
and inspection of the frame once every 75 hours of use
ing does not turn smoothly or has excessive play, it must
be replaced immediately.
BLUE PAPER RISE · 2021
GEAR CABLES AND HOUSING:
· Inspection of its operation before each ride.
· Replacement of gear cables every 6 months to 1 year
depending on the conditions in which the bicycle is used.

BRAKES:

· Inspection of the operation and wear of the brake pads or
shoes before each ride.
· Check the wear on disc brakes and the cables or
hydraulic lines every 6 months to 1 year depending on
the conditions in which the bicycle is used. Flush the
hydraulic lines once a year.
PEDELEC SYSTEM COMPONENTS:
Regularly check the connections and cables of the ebike
system components. The connections must be clean and
free of debris and foreign objects. The cables must be in
good condition and free of cuts or kinks and bends that
may cause short circuits and lack of electric assistance.
The exterior of the controllers and batteries should not
show signs of damage that may allow water and other
elements to ingress within.
If you notice any damage to the components, contact
your Orbea dealer for a professional diagnosis and/or
replacement.
Read the Warnings of Use and the Relevant
information about the RS batteries sections
of this manual to know about the correct
care of the electric components.
PEDELEC SYSTEM UPDATES:
The ebike systems manufacturers may develop improve-
ments and updates of their pedelec systems overtime that
Some updates in the STEPS system can be performed by
the end consumer via Bluetooth® connecting the bicycle
- to the Shimano Etube Project app.
Read here the Etube Project app manual:
https://si.shimano.com/#/en/iUM/7J4MA/
-
ORBEA | 13
Other updates must be performed by an authorized dealer.
Remind your dealer to check for available updates when
you take your bicycle in for repairs or maintenance.
Some of these checks and maintenance
needs go beyond the mechanical knowledge
of most bicycle users. If you are not quali-
always visit an Orbea dealer for maintenance
on your bicycle and its components. The
failure to perform proper maintenance can
result in malfunctions and accidents with se-
rious consequences.
Maintenance performed incorrectly can dam-
age the components, which are not covered
by the warranty conditions.
R EPLAC EM ENT PA RTS
Always use original Orbea or Shimano replacement parts
or those from the component manufacturer in question.
The use of non-original replacement parts may
cause damage that results in malfunctions and
accidents with serious consequences.
The installation of some of the replacement
parts in this technical manual are beyond
the mechanical knowledge of most bicycle
replacement parts, always visit an Orbea
dealer for maintenance on your bicycle and
its components. The failure to properly install
replacement parts can result in malfunctions,
accidents and serious injuries.
The installation of non-original replacement
parts can damage your bicycle and is not
covered by the warranty conditions.
EN