Table of Contents
Advertisement
Quick Links
220V 160AMP TIG MMA PLASMA ARC WELDER INVERTER CUTTER
ITEM: 55137
OWNER'S MANUAL AND SAFETY INSTRUCTIONS
SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT'S
SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH
AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER).
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: (909) 628 4900 MON-FRI 9AM TO 3PM PST
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stark 55137
Summary of Contents for Stark 55137
- Page 1 220V 160AMP TIG MMA PLASMA ARC WELDER INVERTER CUTTER ITEM: 55137 OWNER’S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER).
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. SAFETY The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. - Page 3 IMPORTANT SAFETY INFORMATION Dress properly. DO NOT wear loose clothing, dangling objects, or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts. Air vents on the tool often cover moving parts and should be avoided. Wear the proper personal protective equipment when necessary.
- Page 4 IMPORTANT SAFETY INFORMATION Avoid overexposure to fumes and gases. Always keep your head out of the fumes. DO NOT breathe the fumes. Use enough ventilation or exhaust, or both, to keep fumes and gases from your breathing zone and general area. Where ventilation is questionable, have a qualified technician take an air sampling to determine the need for corrective measures.
-
Page 5: Technical Parameters Table
MACHINE DESCRIPTION AND SPECIFICATIONS The CT416 has arc welding, sticking and plasma cutting three processes which adopt the most advanced inverter technology. Inverter gas-shielded welding power source utilizes high-power component MOSFET to transfer 50/60HZ frequency up to 100KHZ, then reduce the voltage and commutate and output high-power voltage via PWM technology. -
Page 6: Parts And Accessories
PARTS AND ACCESSORIES GAS DELAY SHUT OFF SWITCH INDICATOR LIGHTS OUTPUT POWER CURRENT SWITCH ADJUSTER CUT CURRENT SCALE NEGATIVE OUTPUT POSITIVE OUTPUT TERMINAL TERMINAL GAS/ TORCH TIG/MMA ELECTRICITY SWITCH WELDING OUTPUT SOCKET CURRENT SCALE TERMINAL ELECTRODE GROUND HOLDER CLAMP PLASMA TORCH TIG TORCH ARGON... -
Page 7: Quick Start Operation
QUICK START OPERATION TIG WELDING FUNCTION 1. Turn on the power switch at the back panel, digital current meter is normal and the fan begins to turn. 2. Open the valve of the Argon cylinder, adjust the volume of flow meter and make sure it is adequate for welding. -
Page 8: Operation
OPERATION AIR REGULATOR INSTALLMENT AND OPERATION 1. Tighten and seal the copper air hole at the IN and OUT terminal by the high pressure tube. 2. Tighten and seal the meter. 3. Fix the connecting shelf with a screw at the regulator position. 4. -
Page 9: Troubleshooting
OPERATION 6. Cutting function: Use the pressure resisting air pipe to connect the air intake and compressed air source and use the hoop and tighten to the joint. The air source should supply suitable pressure flow and be dry. If your air source does not meet these requirements, consider using a compressor of the right power and air-decompressing filter. - Page 10 TROUBLESHOOTING...
-
Page 11: Preventative Measures
PREVENTATIVE MEASURES ENVIRONMENT 1. The machine should be operated in dry environments with humidity levels of max 90%. 2. Ambient temperatures should be between -10 to 40 degrees centigrade. 3. Do not weld in direct sunlight or wet conditions. 4. Do not use the machine where conductive dust or corrosive gas are present. CLEANING AND MAINTENANCE 1. -
Page 12: Please Read The Following Carefully
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Need help?
Do you have a question about the 55137 and is the answer not in the manual?
Questions and answers