Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Panasonic HMs700 Series
Summary of Contents for Panasonic HMs700 Series
- Page 1 TOUCH TERMINALS HMs700 Series Instruction Manual ACGM0198V2EN Version 2.0...
-
Page 2: Table Of Contents
Table of contents Introduction ...........................3 Important symbols ........................4 Special instructions for use ......................5 Standards and approvals ......................6 HMs705 ..........................6 HMs707, HMs710, HMs715, HMs721 ...................6 Product overview ..........................7 Technical data common to all models ..................8 6.1 Hardware specifications ......................8 6.2 Environmental conditions ......................8 6.3 Electromagnetic compatibility (EMC) ..................9 6.4... -
Page 3: Introduction
Introduction Introduction This instruction manual contains information about the installation, transportation, storage, assembly, use and maintenance of touch terminals of the HMs700 series. The following models are available: • HMs705: Touch terminal with 5” TFT color widescreen, multi-touch capacitive touchscreen, Ethernet port PoE • HMs707: Touch terminal with 7” TFT color widescreen, multi-touch capacitive touchscreen, Ethernet port PoE • HMs710: Touch terminal with 10.1” TFT color widescreen, multi-touch capacitive touchscreen, Ethernet port • HMs715: Touch terminal with 15.6” TFT color widescreen, multi-touch capacitive touchscreen, Ethernet port • HMs721: Touch terminal with 21.5” TFT color widescreen, multi-touch capacitive touchscreen, Ethernet port... -
Page 4: Important Symbols
Important symbols Important symbols One or more of the following symbols may be used in this documentation to indicate the type of haz- ard. DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Notice Indicates a property damage message. -
Page 5: Special Instructions For Use
Special instructions for use Special instructions for use • The product shall only be used in an area of not more than pollution degree 2, as defined in IEC/ EN 60664-1. • The product shall be installed in an enclosure that provides a degree of protection not less than IP54 in accordance with IEC/EN 60079-15. • Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the product. • Install the product according to the accompanying installation instructions. • Ground the product according to the accompanying installation instructions. • Only qualified personnel may install or repair the product. • Care shall be taken to avoid that layers of dust form on the touch terminals in a way that might cause the accumulation of static charges. • Keep the faceplate of the product clean. The product must be cleaned only with a soft cloth and neutral soap product. Do not use solvents. • This product should not be used for purposes and methods other than indicated in this document and in the documentation accompanying the product. -
Page 6: Standards And Approvals
Standards and approvals Standards and approvals The products are in compliance with the Restrictions on Certain Hazardous Substances (RoHS) Direc- tive 2011/65/EU. In compliance with the relevant regulations the products are CE marked. HMs705 The product has been designed for use in an industrial environment in compliance with the 2014/30/ EU EMC Directive. The product complies with the following standards: EN 61000-6-4 EN 61000-4-2 EN 61000-6-3 EN 61000-4-3 EN 61000-6-2 EN 61000-4-4 EN 61000-6-1 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 HMs707, HMs710, HMs715, HMs721 The products have been designed for use in an industrial environment in compliance with the 2014/53/ EU EMC Directive. The products comply with the following standards: EN 61000-6-4 EN 61000-6-2 EN 61000-6-3 EN 61000-6-1 ETSI EN 301 489-1 ETSI EN 301 489-17 ETSI EN 300 328 EN 62311 EN 61010-1 EN 61010-2-201 Standard radio signal: Wi-Fi 2,4 GHz (calculated according to EN 62311) -
Page 7: Product Overview
Product overview Product overview The HMs700 series touch terminals are ideal for field installation in critical areas. They are equipped with a high resolution display and a multi-touch capacitive touchscreen with a robust glass front. Power over Ethernet (PoE) technology is available for maximum connectivity through standard CAT5 wiring. The HMs700 series can be installed under difficult environmental conditions (IP67 protection) and can be mounted to all standardized support arm systems. The product features environment and motion sensors and has been designed as IIoT edge device for Industry 4.0 applications. The HMs700 series touch terminals have been optimized to run the HMWIN software for powerful HMI applications. • Open platform for Linux applications • OPC UA server / client gateway • Integrated sensors (temperature and acceleration) • Powerful browser with industry standard web engines • Wi-Fi (HMs707, HMs710, HMs715, HMs721) -
Page 8: Technical Data Common To All Models
Technical data common to all models Technical data common to all models Hardware specifications Touchscreen technology Projected capacitive, multi-touch Real-time clock back-up 3V, 7mAh lithium, rechargeable, not user-replaceable, model battery VL1220 Flash 4GB (HMs705, HMs707, HMs710) 8GB (HMs715, HMs721) 1GB (HMs705, HMs707, HMs710) 2GB (HMs715, HMs721) Hardware clock Clock/calendar with back-up battery Accuracy real-time clock <100ppm (at 25°C) Environmental conditions Operating temperature -20 to +55°C (vertical installation) EN 60068-2-14 (surrounding air tempera- ture) Storage temperature -30 to +80°C... -
Page 9: Electromagnetic Compatibility (Emc)
Technical data common to all models Electromagnetic compatibility (EMC) Radiated disturbance test Class A (HMs707, HMs710, HMs715, CISPR 22 HMs721) CISPR 16-2-3 Class B (HMs705) Electrostatic discharge immunity 8kV (air electrostatic discharge) EN 61000-4-2 test 4kV (contact electrostatic discharge) Radiated, radio frequency, 80MHz–1GHz, 10V/m EN 61000-4-3 electromagnetic field immunity 1.4–2GHz, 3V/m test 2–2.7GHz, 1V/m Burst immunity test ±2KV DC power port EN 61000-4-4 ±1KV signal line Surge immunity test ±0.5KV DC power port (line to earth) EN 61000-4-5 ±0.5KV DC power port (line to line) ±1KV signal line (line to earth) -
Page 10: Surface Resistance
Technical data common to all models Surface resistance The HMs700 series front glass is resistant (no visible changes) to the following chemicals after an application time of 24 hours: • Betadine (10% povidone solution) • Cola • Electrode gel/paste • Hydrogen peroxide (3% solution) • NaCl (0.9% solution) • Coffee • Dextrose (5% glucose solution) • Hydrogen chloride (0.5% solution pH=1) • Isopropyl alcohol • Sodium hypochlorite • Ethyl alcohol (70–90%) • Quaternary ammonium compound Touchscreen properties • Multi-touch operation: up to 5 fingers simultaneously • Glove operation: supported Projected capacitive touchscreens (PCAP) are suitable for operation with or without gloves. A large number of gloves (rubber gloves, light/heavy leather gloves, disposable latex gloves, etc.) are supported. However, due to the variety of commercially available gloves, we cannot guarantee the operation with all glove types. • Passive stylus pens: supported •... -
Page 11: Technical Data By Model
Technical data by model Technical data by model HMs705, HMs707, HMs710 Model HMs705 HMs707 HMs710 Display / Backlight TFT Color / LED Colors Resolution 800 x 480 1024 x 600 1280 x 800 Display size (inch) 5” widescreen 7” widescreen 10.1” widescreen Dimming yes (to 0%) Brightness 300cd/m² typ. 400cd/m² typ. Horizontal viewing angle L/R: typ. 70° L/R: typ. 75° L/R: typ. 85° Vertical viewing angle U: typ. 50°... -
Page 12: Hms715 Hms721
Technical data by model HMs715, HMs721 Model HMs715 HMs721 Display / Backlight TFT Color / LED Colors Resolution 1366 x 768 1920 x 1080 Display size (inch) 15.6” widescreen 21.5” widescreen Dimming Brightness 400cd/m² typ. Horizontal viewing angle L/R: typ. 80° L/R: typ. 89° Vertical viewing angle U/D: typ. 80° L/R: typ. 89° User memory flash Operating system Linux RT ARM Cortex-A9 quad core, 800 MHz Ethernet port 10/100Mbit PoE USB port 1 host interface, version 2.0, max. 500mA... -
Page 13: Unpacking And Packing Instructions
Unpacking and packing instructions Unpacking and packing instructions HMs705, HMs707, HMs710 HMs715, HMs721 To repack the product, please follow the instructions backwards. -
Page 14: Product Dimensions
Product dimensions Product dimensions HMs705 105.1mm 148.3mm 16.5mm 17mm Rear view... - Page 15 Product dimensions HMs707 131.6mm 195.2mm 16.5mm 17mm HMs710 183.1mm 264.5mm 16.5mm 17mm...
- Page 16 Product dimensions HMs715 248mm 398.6mm 26.5mm 17mm HMs721 325.6mm 534.1mm 26.5mm 17mm...
- Page 17 Product dimensions HMs707, HMs710, HMs715, HMs721 rear view * HMs715 and HMs721 only...
-
Page 18: Installation
Installation 10. Installation 10.1 Installation environment The product is not intended for continuous exposure to direct sunlight. There is a risk that the product might be overheating. The product is not intended for installation in contact with corrosive chemical compounds. Check the resistance of the front panel film to a specific compound before installation. Do not use tools of any kind (screwdrivers, etc.) to operate the touchscreen of the product. IP67 is guaranteed only if: • An appropriate cable (JSCAxxxx) is used. The cables JSCAU001, JSCAU002, JSCAU003 and JS- CAU004 can be orderd as accessories. • The max. deviation from the plane surface to the cutout is ≤0.5mm. • The thickness of the case where the product is mounted is from 1.5mm to 3mm. • The max. surface roughness where the gasket is applied is ≤120μm. 10.2 Installation procedure For details on installation, refer to the Installation Guide provided with the product. Cable Max. 3mm JSCAxxxx (IP67) Max. 10mm Standard Ethernet Notice Tightening torque: 1000Ncm (nut),130Ncm (screw) -
Page 19: Connections
Connections 11. Connections 11.1 Ethernet port Pin Description Reserved The Ethernet port has two LED status indicators. They work as shown in the following figure. Red LED Green LED Red LED • Off: Valid link has not been detected • On: Valid link has been detected Green LED • On: No activity • Blinking: Activity 11.2 Power supply, grounding, and shielding The power is transmitted over a network cable (PoE). NOTE Make sure that the power supply has sufficient power capacity for the operation of the product. The product must always be grounded to earth with a shielded network cable (CAT5 or higher). Grounding helps limit the effects of noise due to electromagnetic interference on the control system. Earth connection can also be done using the screw located near the connector. A label identifies the ground connection. All the electronic devices in the control system must be properly grounded. Grounding must be per- formed according to applicable regulations. -
Page 20: Battery
Battery 12. Battery The touch terminals are equipped with rechargeable lithium batteries that are not user-replaceable. The battery is needed to keep the real-time clock running (date and time). When the touch terminal is installed for the first time, the battery must be charged for 48 hours. When the battery is fully charged, data backup at 25°C is guaranteed for 3 months. This symbol indicates the battery location. HMs705 HMs707... - Page 21 Battery HMs710 HMs715 HMs721...
-
Page 22: Getting Started
Getting started 13. Getting started The HMs700 series touch terminals must be programmed with the programming software HMWIN Studio (starting from v2.6), a Windows application. There are two options to transfer a HMWIN application project to a touch terminal: Ethernet Connect the touch terminal via the Ethernet interface to a personal computer running the HMWIN Studio software. Select “Run/Download to target” in HMWIN Studio. Make sure that the firewall policy is configured in a way that allows HMWIN Studio to access the network. Create an update package using the HMWIN Studio software and copy it to a USB flash drive. For USB transfer a dedicated accessory cable is required. -
Page 23: System Settings
System settings 14. System settings 14.1 Introduction The HMs700 series touch terminals have a system settings interface to allow the configuration of system options. The user interface of “System Settings” is based on HTML pages accessible locally on the touch ter- minal or remotely using a web browser, e.g. Chrome v44 or higher on port 443. To connect, enter the address https://IP/machine_config. “IP” represents the address of the touch terminal. The default user name is “admin”, and the default password is “admin”. Use the navigation menu on the left side of the screen to browse through the available options. On the left side, the selected menu item is highlighted. The right side shows related information and settings. Depending on the size of the touch terminal, menu and content of the selected menu item may not be displayed next to each other on the screen. The system settings interface has two operating modes: User mode HMWIN runtime is running or the status of the touch terminal is set to “factory default”. System mode HMWIN runtime is not running or there is a software failure. The system mode includes all options available in user mode. In addition, the system mode offers commands dedicated to system upgrade and recovery which are not available in user mode. 14.2 Activation of system settings in user mode Factory default Touch the “System Setting” button on the touch terminal. status HMWIN runtime Touch and hold any unused area of the touchscreen for a few seconds to access running the context menu. The default holding time is 2 seconds. Select “System Setting”... -
Page 24: Activation Of System Settings In System Mode
System settings 14.3 Activation of system settings in system mode Normal If HMWIN runtime is not running: operation Touch the “System Setting” button on the touch terminal to open the system set- tings in user mode. Select “Restart” > “Config OS” to reboot in system mode. If HMWIN runtime is running: Touch and hold any unused area of the touchscreen for a few seconds to access the context menu. The default holding time is 2 seconds. Select “System Setting” from the context menu. Select “Restart” > “Config OS” to reboot in system mode. Recovery If the touch terminal is not responsive, tap on the surface of the touchscreen during operation the power-up phase. The tapping frequency must be high. Start tapping the touch- screen as soon as power has been supplied to the product. The message “TAP-TAP DETECTED” appears when the operating sequence has been recognized. Release the touchscreen to boot in user mode without running HMWIN runtime or touch and hold the touchscreen for a few seconds. Then select “Restart” > “Config OS” to boot in system mode. 14.4 Options available in system settings The following important basic setting options of the touch terminal are available: Language Configure the language used for the system setting menu only. System Shows information about platform, status and timers (e.g. system on time, backlight on time). Logs Enable continuous log for BSP and allow to export it. -
Page 25: Disposal
Disposal 15. Disposal Used electrical and electronic products must not be placed in general household waste. For proper treatment, recovery and recycling of old products, take them to applicable collection points in accordance with your national legislation. By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local municipality. Dispose of batteries according to local regulations. -
Page 26: Record Of Changes
Record of changes 16. Record of changes Manual No. Date Description of changes ACGM0198V2EN February 2021 Second edition based on the JSmart700 Series Oper- ating Instructions version 1.02 and JSmart705 Series Operating Instructions version 1.00 Added information about the appropriate cables (IP67) Added information about classification for HMs705 ACGM0198V1EN December 2020 First edition based on JSmart700 Series Operating Instructions version 1.01 and JSmart705 Series Oper- ating Instructions version 1.00 Distributed by Panasonic Electric Works Europe AG www.panasonic-electric-works.com Subject to change without notice. The information contained in this document is provided for informational purposes only. While efforts were made to verify the accuracy of the information contained in this documentation, it is provided “as is” without warranty of any kind. Third-party brands and names are the property of their respective owners. - Page 27 Filial Nordic, Knarrarnäsgatan 15, 164 40 Kista, Sweden, Tel. +46 859476680, Fax +46 859476690, www.panasonic-electric-works.se Panasonic Fire & Security Europe AB Jungmansgatan 12, 21119 Malmö, Tel. +46 40 697 7000, Fax +46 40 697 7099, www.panasonic-fi re-security.com Poland Panasonic Industry Poland sp. z o.o.