Table of Contents
Advertisement
HS5B/HS5E Door Handle Actuator
Instructions
5.
Install the switch cover unit on the mounting frame and
panel. Mounting screws or nuts are not supplied and must
be provided by the user.
Mounting Screws
Installing the rear unlocking button
When the total thickness of mounting panel is 3.0 mm or
less: Install the rear unlocking button on the rod on the back
of the switch. For details, see the instruction sheet or catalog
(EP1199) for the HS5E.
When the total thickness of mounting frame or panel is 20
mm or more: Install the rear unlocking button kit (HS9Z-
FL5∗) sold separately. For installation, see the instruction
sheet for the HS9Z-FL5 or catalog (EP1199) for the HS5E.
Installing the Handle Unit HS9Z-DH5RH
1.
Install the front handle (black) on the shaft on the actuator
cover as shown below.
Shaft
2.
Tighten Screw D attached to the handle
using a hexagonal wrench (size: 2.5).
Apply Loctite to the screw so that it does not
become loose.
3.
Install the handle unit on the
and panel, aligning the handle unit and
switch cover unit as illustrated under
"Actuator Mounting Reference Posi-
tion." Mounting screws and nuts are
not supplied and must be provided by
the user.
4.
Cut the rear handle shaft according to the thickness of the
mounting frame and panel.
5.
Align the rear handle plate, rear handle shaft, and the rear
handle base as shown below, and fasten them using two
Screws E. Apply Loctite to the screws so that they do not
become loose.
Shaft Positioning Pin
Rear Handle
Shaft
Rear Handle
Plate
6.
Install the rear handle (yellow) on the rear
handle shaft.
12
Mounting holes required
in the frame. See Dimensions
on page 10.
Nuts
Handle Position
Locked
Unlocked
Screw D
mounting frame
Mounting
Screws
Mounting panel
thickness (X)
Cut at →
0 < X ≤ 10mm:
1
Cut at →
10 < X ≤ 20mm:
2
Cut at →
20 < X ≤ 30mm:
3
Cut at →
30 < X ≤ 40mm:
4
Cut at →
40 < X ≤ 50mm:
5
Cut at →
50 < X ≤ 60mm:
6
No cut →
60 < X ≤ 70mm:
7.
Tighten S
crew D attached to the handle using a hexagonal
wrench (size: 2.5). Apply Loctite to the screw so that it does
not become loose.
8.
Turn the handle to the locked position, and insert the rear
handle shaft into the actuator cover. The rear handle should
be in the locked position.
9.
While adjusting to ensure
smooth operation of the rear
handle, fasten the rear handle
unit on the mounting frame and
panel.
∗ Install the HS9Z-DH5LH in a
similar fashion as the HS9Z-
DH5RH. Note that the handle
direction becomes opposite.
∗ Mounting screws and nuts are not supplied and must be pro-
vided by the user.
Actuator Mounting Reference Position
The mounting reference position and allowable mounting
•
range are as shown below.
Use the square dot pattern as a guide of the allowable mount-
•
ing range.
2
Nuts
LOCK
UNLOCK
4
Installing the Rear Unlocking Button Kit
1. Install the connecting rod onto the
push rod on the HS5E-∗44L∗∗-G rear
unlocking button type interlock
switch.
2. A pin is attached to the connecting
rod. Using pliers, press the pin into
the hole in the push rod.
3. Pull out the connecting rod from the
hole in the mounting frame, and turn
the button operating pin to the horizontal position.
Connecting
Rod
Pull
Screw D
Locked
Nuts
Unlocked
Mounting
Screws
0.8
Reference Position
3
7 to 9
2
Reference
Position
4
LOCK
UNLOCK
Push Rod
Connecting
Rod
HS5E-∗44L-∗∗-G
Interlock Switch
Pin
Connecting Rod Orientation
Correct
Incorrect
(08/03/12)
Advertisement
Table of Contents
