IDEC HS5B Manual page 11

Instructions
The door handle actuator can be used with the HS5B-
•
(metal head type) and HS5E-∗44L∗∗-G (rear unlocking button
type) only. Do not use with other interlock switches.
When using the door handle actuator in the safety-related part
•
of the system, make sure of proper operation while observing
the safety standards and regulations of the relevant country
or region where the actual machine/system is used. Also, per-
form a risk assessment before operation.
Read the instruction sheet of interlock switch before installing
•
the door handle actuator.
Install the switch cover unit and handle unit on the outside of
•
the door. Do not install them inside the door, otherwise the
door cannot be opened or closed by the operator, affecting
the operation and causing danger to the operator.
Install the door handle actuator in the direction
•
as shown on the right, so that the cable faces
downward. Do not install in any other direction,
otherwise malfunction will be caused.
Do not modify or disassemble the door handle
•
actuator.
Padlocking
When padlocking the HS9Z-DH5, lift the
•
knob on the front of the HS9Z-DH5. A tab
will appear. Install padlock(s) or a hasp on
the tab.
Make sure that the total load by the pad-
•
locks and hasp does not exceed 30N. Oth-
erwise the door handle actuator will be-
come deformed or damaged.
The applicable shackle diameter of padlock is ø6.0 to 7.5 mm.
•
Shackle Diamete
Manual Unlocking
When using the HS5E-
•
∗44L∗∗-G interlock switch, at-
tach the manual unlock label
on the front of the switch cover
unit.
For manual unlocking, refer
•
to the catalog for the HS5E
interlock switch with solenoid
(EP1199).
Handle Operation
Push the handle, and turn the handle to insert the actuator.
•
Handle Operation
➀ Push the handle
Note: Do not force to turn the handle without pushing in the
handle, otherwise damage will occur.
Do not close the door when the actuator is in the locked sta-
•
tus, otherwise the actuator will hit the door, resulting in defor-
mation or damage.
When turning the handle, make sure that your hands or fi n-
•
gers are not caught by the door.
(08/03/12)
∗∗Z
Cable
Padlock Tab
Padlock Knob
Manual Unlock
Label
LOCK UNLOCK
LOCK UNLOCK LOCK UNLOCK
Normal Status Unlocked Status
➁ Turn the handle
HS5B/HS5E Door Handle Actuator
Installation
Check wether the following parts are included.
•
Unit Type
Mounting Bracket
Switch Cover
Blind Cap
Switch Cover Unit
HS9Z-DH5C
Screw A ∗
Screw B ∗
Screw C
Actuator Cover
Front Handle (black)
Rear handle (yellow)
Handle Unit
Rear handle Shaft
HS9Z-DH5RH
Rear handle Plate
HS9Z-DH5LH
Rear handle Base
Screw D ∗
Screw E
Mounting Plate
HS5B Installation Kit
HS9Z-DH5B
Spacer
∗ Screws A and B are loosely attached to the switch cover.
Screws D are loosely attached to the handles.
Installing the Switch Cover Unit (HS9Z-DH5C)
1. Remove one Screw A and two
Screws B from the switch cover
and remove the switch cover
from the mounting bracket.
2. [HS5E- ∗44L∗∗-G Interlock Switch]
Using four Screws C, install the
interlock switch on the mounting
bracket (panel thickness 3 mm or
less). When installing on a mounting
panel (X) of 20 ≤ X ≤ 40 mm, install
the connecting rod onto the push
rod and press the pin into the hole in the push rod as de-
scribed in the " Installing the Rear Unlocking Button Kit" on page
12, before installing the switch on the mounting bracket
[HS5B-∗∗Z Interlock Switch]
Install the interlock switch using the
HS5B Installation Kit (HS9Z-DH5B)
and two Screws C.
3. Plug the unused actuator entry
slot using the blind cap. To do
so, attach the tab on one end to
the switch cover, and bending
the blind cap, attach the other
end on the switch cover.
4. Install the switch cover on the mounting
plate using one Screw A and two
Screws B.
Part Quantity
1
1
1
1
2
4
1
1
1
1
1
1
2
2
1
2
Screw A
Mounting
Bracket
Switch Cover
Screws B
Screw C
HS5E-∗44L∗∗-G
Interlock Switch
.
Spacers
Screws C
HS5B-∗∗Z
Mounting Plate
Interlock Switch
Inside
Outside
Blind Cap
Blind Cap
Switch Cover
Screw A
Screws B
11