Packing List The following items are included: Large Preheater Unit ......1 unit Large PCB Support ........ 1 unit Ref. PHB-SA Console ......1 unit RJ45 Cable ....1 unit Power Cord .....1 unit Ref. ACE-A Ref. 0019914 Ref. 0023715 (120V) 0023714 (230V) 0024092 (100V) Kapton Tape ....
w w w.jbctools.com Features and Connections Heater Unit Heating Areas Zone A Zone B Fixing Brackets for Large PCB Support Thermocouple Connectors x4 (Type K) Pedal Connector RJ12 Connector Power to Robot RJ45 Connector Power Socket to Console USB-B Connector Button for Foot Folding and Console...
Height Adjustment It allows adjustment for 3 heights between the PCB and the Heating Area of the Preheater. Low level 28 mm Medium level 38 mm High level 48 mm To change the height, do as follows: To raise the support, hold the base and pull up. To lower the support, press the button and move down.
Page 5
w w w.jbctools.com Fast PCB Replacement The support lets you replace PCBs of the same batch fast and easily. Use the sliding guides to change the PCBs. Removing the PCB Placing another PCB Loosen one sliding guide, pull back and lift Position it and tighten the sliding guide knobs.
º Selected 120 º º º º Power C 100 P 100 P 100 º º º P 100 º Work Screen The Console offers an intuitive user interface which provides quick access to station parameters. 14:15 Status Bar 14:15 º...
w w w.jbctools.com Setting Thermocouples Function Select Thermocouples from the Work mode menu to set them up. The thermocouples (TC) can work in three diferent ways depending on what is needed. · Control: the unit mantains the selected temperature. · Protection: the Heater Unit stops if the TC reaches the selected temperature. ·...
º º Selected 120 Work Mode º º º º Power C 100 P 100 P 100 º º º P 100 º Temperature Mode Select Temp. mode from the Work mode menu. In this mode the heater unit maintains the selected temperature for the TC1 thermocouple as long as the other TC’s do not reach the control/protection temperature limit.
Page 9
w w w.jbctools.com º º º Profile Modes Select Profile Mode from the Work Mode Menu. In this mode the heater unit regulates the temperature of the TC1 thermocouple according to the selected profile as long as the other TCs do not reach the control/protection temperature limit.
JBC Set Profiles There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number of steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are needed to obtain a gradual warming.
w w w.jbctools.com Process Analysis By pressing Graphics in the main MENU, temperature of TC1 thermocouple and power fi gures in real time are displayed. Graphics 14:15 Power (%) Temperature (ºC) Power [%] Ext. Temp [ºC] Switch Y Axis Between Power and Temperature System Notifications The following icons will be displayed on the screen’s status bar.
Page 12
Insert a USB flash drive into the USB-A connector to export / import profiles. Update the Station Software 1. Download the JBC Update File from 2. Insert the USB flash drive to the console. www.jbctools.com/software.html and save The icon is diplayed while updating.
- Only if it is absolutely necessary and if cleaning with isopropyl alcohol (IPA) is not enough, it is recommended to use a scraper to remove dirt in the glass area. - Replace any defective or damaged parts. Use original JBC spare parts only. - Repairs should only be performed by a JBC authorized technical service.
Page 14
Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than PCB preheating. Incorrect use may cause fire. - The mains cable must be plugged into approved bases. Make sure that it is properly grounded before use.
w w w.jbctools.com Specifications Large Preheater Set PHBE-1KA 120V. Input 120V 50/60Hz Fuse 15A PHBE-2KA 230V. Input 230V 50/60Hz Fuse 10A PHBE-9KA 100V. Input 100V 50/60Hz Fuse 15A Large Preheater Unit - Maximum Power: 1800W / 1800W / 1400W - Heating Area: 180 x 277 mm / 7.1 x 10.9 in - 1 zone 360 x 277 mm / 4.2 x 10.9 in - 2 zones - Ambient Operating Temperature:...
Page 16
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase. This product should not be thrown in the garbage.