Related Manuals for Inepro Sales Master
Summary of Contents for Inepro Sales Master
- Page 1 Sales Master - SM001 / SM002 Technical Manual | Sales Master - SM001 / SM002 © 2019 Inepro B.V. All rights reserved...
- Page 3 Sales Master - SM001 / SM002...
-
Page 5: Table Of Contents
Table of Contents Models Introduction Installation Initiation Coin Hoppers Maintenance Function Menu Function Overview Programming example Ticket Dispencers Optional General technical data Troubleshooting VMS-1 Overview Version 2.5.2 Inepro B.V. http://www.inepro.com... - Page 7 Always disconnect the power supply before removing the hoppers/dispensers! Read the manual before switching on this device. Before switching on this device, make sure that the power supply is 220V / 240VAC 50Hz. Your supplier does not take any responsibility if the safety norms are not followed.
-
Page 9: Models
Models Part... - Page 10 Models Models Tick the box of the correct machine. Sales Master - SM001 / SM002...
-
Page 11: Introduction
Introduction Part... - Page 12 Banknote reader Armatic Money and/or ticket return units: § Coin hopper Asahi Seiko SA-595 § Ticket dispenser Asahi Seiko CD-200 § Coin-Control hopper C-24/MK-2 Optional: § Shaft elongation pieces to increase the coin or ticket capacity. Sales Master - SM001 / SM002...
-
Page 13: Installation
Installation Part... - Page 14 Make sure the machine is perfectly level; · Connect the machine to a clean group with earth connection; · The connection of the machine should be permanent (without socket) or to a wall socket well out of the user’s reach. Sales Master - SM001 / SM002...
-
Page 15: Initiation
Initiation Part... - Page 16 Change the menu if wrong values are returned. In case you have a machine which returns 2 types of coins / products it is very important that each hopper /dispenser is filled with the correct coins / tickets. Sales Master - SM001 / SM002...
-
Page 17: Coin Hoppers
Coin Hoppers Part... - Page 18 These copper plates always have to be covered by coins to avoid the activation of the 'empty' signal. Like this, there are always enough coins left, and you can refill before the 'empty' signal is activated. Sales Master - SM001 / SM002...
-
Page 19: Maintenance
Maintenance Part... - Page 20 We recommend you to contact the supplier of the machine with regard to the maintenance of banknote readers and ticket dispensers; he will inform you about a maintenance contract. Sales Master - SM001 / SM002...
-
Page 21: Function Menu
Function Menu Part... - Page 22 F 42 represents the hopper/dispenser 1 Function F 43 represents hopper/dispenser 2 Pressing the function button, the number of returned coins/products is shown in the display. Remove the jumper to return to the user mode. Sales Master - SM001 / SM002...
- Page 23 Resetting the counters The revenue/coin counters (F 32 till ) can be reset. To reset the counters, push simultaneously the up and down button. Make sure you do this while the value of the chosen function is shown on the display.
-
Page 25: Function Overview
Function Overview VIII Part... - Page 26 Verkoopprijs 2d Functie F04, Verkoopprijs 1c. Munt / productw aarde hopper 2. Functie Waarde Omschrijving Basis waarde 0-255 Aantal uitgave uit hopper/dispenser 2 bij munt 4. Note: Timer Input f unction, zie Timer Input Sales Master - SM001 / SM002...
- Page 27 Automatische reset tijd van het betalingskrediet Functie F08, Functie F08, Autom atische reset tijd van het betalingskrediet . Functie Waarde Omschrijving Basis waarde Autom atische reset tijd van het betalingskrediet (in 0-255 m inuten). Relais K-4 tijd output Functie F09, Functie F09, Relais K-4 tijd output.
- Page 28 Functie F20-F29, Waarde m unt 1 - m unt 10. Functie Waarde Omschrijving Basis waarde 0-255 Waarde munt Functie F30, Muntwaarde hopper/dispenser 1 Functie Functie F30, Muntw aarde hopper/dispenser 1. Waarde Omschrijving Basis waarde Muntw aarde hopper/dispenser 1. 0-255 Sales Master - SM001 / SM002...
- Page 29 Muntwaarde hopper/dispenser 2 Functie F31, Functie F31, Muntw aarde hopper/dispenser 2. Functie Waarde Omschrijving Basis waarde 0-9999 Muntw aarde hopper/dispenser 2. Functie F32-F41, Inkomsten teller munt/biljet 1-10 Functie F32-F41, Inkom sten teller m unt/biljet 1-10. Functie Waarde Omschrijving Basis waarde 0-9999 Inkomsten teller munt/biljet.
- Page 30 Pin 1 Pin 2 Pin 3 Pin 4 Prijs F00 / F04 Off 1a / 2a F01 / F05 Off 1b / 2b F02 / F06 On 1c / 2c F03 / F07 On 1d / 2d Sales Master - SM001 / SM002...
-
Page 31: Programming Example
Programming example Part... - Page 32 "error", text in display in case of w rong payment "empty", text in display if one of the hopper is empty F19 - F30 Function F 19 to F 30 have to be in position 1 to confirm the registration/admittance of the coins. Sales Master - SM001 / SM002...
-
Page 33: Ticket Dispencers
Ticket Dispencers Part... - Page 34 Shuffle the ticket before introducing them into the dispenser to avoid their sticking to one another, and put the weight onto the ticket stack. The 'empty' signal is activated when the last ticket is given out. Sales Master - SM001 / SM002...
-
Page 35: Optional
Optional Part... - Page 36 A programming device, to simplify the operation of the function-menu. A reset and counting device, to read the counters only and to reset the daily counters. PC support software, on-line connection, to run various sales machines. Sales Master - SM001 / SM002...
-
Page 37: General Technical Data
General technical data Part... - Page 38 Count Dow n key Keys (Integrated on the · Count Up key VMS-1 m ain board) · Empty Hopper/Dispenser key · Reset key Weergave 4-w ay LED display Weight Weight About 35 kg. (depending on the configuration) Sales Master - SM001 / SM002...
-
Page 39: Troubleshooting
Troubleshooting XIII Part... - Page 40 Error impossible to be rectified by the user, it is advisable to call EEPROM reading error on a specialist to test the electronic components. Sales Master - SM001 / SM002...
-
Page 41: Vms-1 Overview
VMS-1 Overview Part... - Page 42 6. Hopper / dispenser button 7. Escrow connection 8. Input hopper / dispenser 9. Up button 10.Function jumper 11.Down button 12.Function button 13.Coin acceptor connection 14.Display connection 15.Timer connection 16.5 / 12 / 24V output Sales Master - SM001 / SM002...
- Page 43 Manual R 2 - 35...