Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for JETWAY JBC501F697-Q170-B
Summary of Contents for JETWAY JBC501F697-Q170-B
- Page 1 Quick Installation Guide NO. G03-JC501QIG02-F Rev ： 1.1 Release date: 2021/1/15...
-
Page 2: To Open The Chassis
Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification. 1. To Open the Chassis Locate the screws in the spots marked on the Turn over the barebone system with the top cover of the system and unscrew them heatsink upwards, as the photo shows. - Page 3 Lift the cover up to open the chassis. Notice: For user to have a clear view of layout, we may unplug some of the cables during installation. In this case, make sure that the cables are plugged into their original places when necessary installation finished for the system to function normally.
- Page 4 Find CPU socket on the board. Please make Remove the plastic protective plastic cover sure that CPU socket is facing towards you from the socket. (Put it to the original place if and the level is on you right hand side. CPU is not installed.
- Page 5 Put down the load plate in the direction shown Press down the load level and move it above. leftwards to make sure it is locked under the notch. Notice ： Please remove the screws that lock the board to the chassis cover when CPU installation completed to install CPU heatsink upon CPU.
- Page 6 1: CPU Thermal conductive gel (P/N: HCS3XXHS2-F*1 pcs), 20*20*0.5mm 2: PWM IC Thermal conductive gel (P/N: HCS501HS1-F*1 pcs), 15* 47*1 mm 3: South Bridge Thermal conductive gel (P/N: HCS501HS2-F *1 pcs), 25*25*1 mm Apply corresponding thermal conductive gels to the bottom side of the heat sinks as the photo show, and then place the CPU, PWM IC and South Bridge heatsink upon the board.
-
Page 7: To Install Msata Card
4. To Install SO-DIMM to the board Find the SO-DIMM slot on the board and Insert the gold-figure side of the compatible open the two eject tabs for further SO-DIMM into the slot. The eject tabs will installation. lock automatically if installed correctly. 5. - Page 8 Insert the gold-figure side of the compatible Lock the card to the board by tightening up Mini PCIe card into the slot at a 30 degree. the screw to the marked spot. 6. To Install WI-FI Card Locate the half-size WIFI slot on the Remove the marked screw and use it to board.
- Page 9 Insert the gold-figure side of the Lock the card to the board by tightening compatible WI-FI card into the slot at a up the screw to the marked position. 30 degree angle and press down. Locate the reserved Wi-Fi antenna holes on the front panel. Remove the semi-broken shield from the panel to install the antenna, as the following details show.
- Page 10 Back-side View: Put the metal ring into the antenna head at first, and then push this antenna head into antenna hole of the rear panel. Front-side View: Put the other metal ring into the antenna head, and then lock the antenna head to the front side of the rear panel with the with hexagonal bolt.
- Page 11 Press the metal hat on the end of the Connect the external Wi-Fi receiver antenna string to the antenna slot on the antenna to the antenna connector on the card as shown (If you install two rear panel. antenna, refer to above steps to finish installation, and press the left metal hat of the left antenna to the left slot, the right metal hat to the right slot).
- Page 12 Lock the SATA hard disk to one of the Lock the SATA hard disk to the other racks by tightening the screws in the rack by tightening the screws in the marked position. marked position. To connect onboard SATA port. To connect SATA hard disk driver.
- Page 13 Plug this side of the cable to SATA Lock the racks hard disk with SATA HDD power-in connector and SATA connector installed to its original places by of the hard disk. tightening the screws in the marked position. Plug the other side cable to the SATA power connector and SATA port connector on the board.
- Page 14 Notice: When all necessary installations are finished, please make sure that all cables unplugged before installations are connected to their original places before restoring the back cover to the chassis and screws on the front panel/back panel/top cover locked to its original places (Refer to Part I). See to it that the cables inside are not blocked or pressed.
- Page 15 Wall mount the system by tightening two screws in the marked positions. Then tighten up the other two screws in the marked positions on the other rack.
Need help?
Do you have a question about the JBC501F697-Q170-B and is the answer not in the manual?
Questions and answers