Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Campbell Apogee Instruments TS100SS
Summary of Contents for Campbell Apogee Instruments TS100SS
- Page 1 Revision: 01/2020 Copyright © 2019 – 2020 Campbell Scientific, Inc.
- Page 2 Limited warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service for twelve months from the date of shipment unless otherwise specified in the corresponding product manual. (Product manuals are available for review online at www.campbellsci.com.) Products not manufactured by CSI, but that are resold by CSI, are warranted only to the limits extended by the original manufacturer.
- Page 3 Campbell Scientific reserves the right to refuse service on products that were exposed to contaminants that may cause health or safety concerns for our employees.
- Page 4 Periodically (at least yearly) check electrical ground connections. WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS, THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR MAINTENANCE OF TRIPODS, TOWERS, OR...
-
Page 5: Table Of Contents
2. Precautions 3. Initial inspection 4. QuickStart 5. Overview 6. Specifications 7. Installation 7.1 Siting 7.2 Mounting 7.3 Wiring 7.4 Programming 8. Maintenance Appendix A. Importing Short Cut code into CRBasic Editor Campbell Scientific regional offices Table of Contents - iv... -
Page 6: Introduction
(p. iii) section at the front of this manual. Care should be taken when opening the shipping package to not damage or cut the cable jacket. If damage to the cable is suspected, consult with Campbell Scientific. The TS100SS is a precision instrument. Please handle it with care. -
Page 7: Quickstart
FIGURE 3-1. Components shipped with the TS100SS 4. QuickStart A video that describes data logger programming using Short Cut is available at: www.campbellsci.com/videos/cr1000x-datalogger-getting-started-program-part-3 . Short Cut is an easy way to program your data logger to measure the sensor and assign data logger wiring terminals. - Page 8 1. Open Short Cut and click Create New Program. 2. Double-click the data logger model. NOTE: If using a solar radiation measurement to control the fan, add the solar sensor to Short Cut before adding the TS100SS. The solar radiation output needs to be in W/m .
- Page 9 4. Click the Wiring tab. Click OK after wiring the sensor. 5. Repeat steps three and four for other sensors you want to measure. Click Next. 6. In Output Setup, type the scan rate, a Table Name, and Data Output Storage Interval. Click Next.
-
Page 10: Overview
7. Select the output options. 8. Click Finish and save the program. Send the program to the data logger if the data logger is connected to the computer. 9. If the sensor is connected to the data logger, check the output of the sensor in the data display in LoggerNet, RTDAQ, PC400, or PC200W to make sure it is making reasonable measurements. -
Page 11: Specifications
wire, there is a pull-up wire (power input). This allows a user-defined maximum output voltage from the tachometer, and facilitates interfacing with multiple measurement devices. 6. Specifications Difference among individual replicate shields: < 0.1 °C Aspiration rate: 6 m s⁻¹ at full speed; 3 m s⁻¹... -
Page 12: Mounting
7.2 Mounting The shield mounts on a crossarm or horizontal pipe (1-1/4 inch to 2 inch IPS). The adapter allows one temperature and relative humidity probe (HygroVUE 5 or HMP60). 1. Attach the hat to the pipe with the U-bolt, nuts, and rubber washers (FIGURE 7-1 (p. - Page 13 FIGURE 7-2. Exploded view 3. With the sensor port facing the nearest pole, align the standoffs to the four corresponding holes in the hat and secure with nylon nuts. 4. Insert the sensor port adapter into the sensor port. 5. Slowly insert the sensor into the adapter until the sensor tip is centered in the air stream. 6.
-
Page 14: Wiring
P, C (control terminal), U configured for White output high-frequency pulse counting U and C terminals are automatically configured by the measurement instruction for Campbell Scientific CR6 data logger. 7.4 Programming Accurate measurements can be made at slower fan speeds under conditions such as during the night, high wind speed, and low solar radiation. -
Page 15: Maintenance
Downloadable example programs are available at: www.campbellsci.com/downloads/ts100ss- example-programs. 8. Maintenance NOTE: All factory repairs and recalibrations require a returned material authorization (RMA) and completion of the “Declaration of Hazardous Material and Decontamination” form. Refer to Assistance (p. ii) page at the beginning of this manual for more information. Regularly inspect the shield and clean as needed by wiping the surface with a moist rag. - Page 16 4. Place the new fan (FIGURE 8-2 (p. 11)) in the shield body and orient the fan so the fan pulls air upwards through the shield towards the hat. FIGURE 8-2. Replacement fan 5. Replace and tighten the screws. 6. Connect the TS100SS cable to the fan-cable connector. TS100SS Aspirated Radiation Shield...
-
Page 17: Appendix A. Importing Short Cut Code Into Crbasic Editor
Appendix A. Importing Short Cut code into CRBasic Editor Short Cut creates a .DEF file that contains wiring information and a program file that can be imported into the CRBasic Editor. By default, these files reside in the C:\campbellsci\SCWin folder. Import Short Cut program file and wiring information into CRBasic Editor: 1. -
Page 18: Campbell Scientific Regional Offices
INFO Global Sales & Support Network A worldwide network to help meet your needs Australia France Thailand Garbutt, QLD Australia Vincennes, France Bangkok, Thailand Location: Location: Location: Phone: 61.7.4401.7700 Phone: 0033.0.1.56.45.15.20 Phone: 66.2.719.3399 info@campbellsci.com.au info@campbellsci.fr info@campbellsci.asia Email: Email: Email: www.campbellsci.com.au www.campbellsci.fr www.campbellsci.asia Website:...