Page 1
Yalp Sona YA 3500 Installation instructions Installatievoorschrift...
Page 2
WARNING WAARSCHUWING Read these installation instructions before you Lees deze installatieinstructies voordat u dit start the installation. Retain this manual for toestel installeert. Bewaar deze handleiding future reference. voor toekomstig gebruik. YA3500-201006...
Page 7
13 mm 17 mm 30 mm Cordless drill Cap Bit M8 Cap Bit M10 Shovel Wire stripper Measuring tape Flat (insulated) Stanley knife Broom Round 0.2-1mm Leveller Philips head 350 kg 800 kg C20/25 Drill + bit 8.8 anchor M20 YA3500-201006...
Lappset Yalp B.V. (hereina er referred to as Yalp) has made every eff ort to ensure that these installa on in- struc ons are accurate.
Page 30
Installed Sona (L x W x H) 4.965x3.800x3.782 m 195.5x149.6x148.9” Sona Turf Floor (uncut) Ø3900mm Ø153.5” Recess radius Ø3800mm Ø149.6” Recess depth 20 mm 0.8” Weight Netto weight Sona 590 kg 1300 lbs Power Power input 100-240 V ~. 50/ 60 Hz. 150W max Power output 12 V DC Energy usage...
REGULATORY INFORMATION USA Changes or modifi ca ons not expressly approved by the party responsible for compliance could void the us- er’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera on.
We, Lappset Yalp B.V., hereby declare that the equipment bearing the model name specifi ed below was tested conforming to the applicable FCC Rules under the most accurate measurement standards possible, and that all the necessary steps have been taken and are in force to assure that produc on units of the same equip- ment will con nue to comply with the Commissions requirements.
Page 33
100-235 Anchor FE360 Galvanized 100-507 Transparent sealant 3200-910 Mould Pinewood 100-213 Button head screw SS304 Lubocoat M10x30 BIT TX45 Torx bit FE360 Galvanized HAND TX45 Torx hand key FE360 Galvanized 100-240 Hex bolt M8x20 FE360 Galvanized 100-243 Hex bolt M8x40 FE360 Galvanized 100-245...
Page 34
Quick drying concrete (C20/ 800 kg 1764 lbs C25 NEN -EN206-1/-8005) Surface mount Drill + bit Advised for anchors Chemical anchor (4000N) e.g. Hilti HIT 170 with 8.8 anchor M20 (in combination with C20/ C25 concrete) A. PREPARATION A.1 TRANSPORTATION ADVICE WARNING Not taking the right precautions •...
• Make sure that the Sona will be placed WARNING A surface mount can only be done perpendicular to and directly on the prepared when the existing surface is made of at least 15 surface cm (5.9”) solid concrete. A.10 Choose the installation type suitable for the DEEP mount (in existing ground): continue with surface on which the Sona will be installed.
D.13 Place the side plate with the button near the D.15 Close the top gap with transparent sealant to computer. Connect all cables to the computer: A. make the Sona watertight. button, B. camera and C. power. D.16 Switch on the main power. WARNING Electric malfunction risk! Connecting NOTICE For settings, service and statistics, visit...
Page 37
repaired or replaced to prevent injuries Tighten the bolts every 6 months to prevent loose bolts Make sure the product can perform a daily restart every day for op mal performance MAINTENANCE FLOORING Brush the grass regularly with a s ff broom or rake Keep the grass free of debris and leaves Remove leaves using a leaf blower or rake Remove any weeds immediately to prevent seed dispersal...
Page 38
Deze installa ehandleiding voorziet niet in informa e omtrent alle mogelijke productvaria es of eventuele toevalligheden die jdens de installa e, het gebruik of het onderhoud van het product kunnen voorvallen. Lappset Yalp B.V. (hierna “Yalp” genoemd) hee er alles aan gedaan om ervoor te zorgen dat deze installa e- handleiding correct is.
Page 39
Gewicht Ne o gewicht Sona 590 kg 1300 lbs Energiegebruik Aansluiting 100-240 V ~. 50/ 60 Hz. Max. 150W Uitgang 12V DC Energiegebruik 3,4W Vermogen in gebruik (gemiddeld) Vermogen in gebruik met lichtset (gem.) Vermogen in idle (standby) 3,2W Vermogen in slaap 3,2W Aansluiting Internet connectie...
Page 40
Nummer Omschrijving Aantal Materiaal Afwerking 199-017 Zijpaneel met knop SS304 Poedercoat 199-024 Zijpaneel SS304 Poedercoat 199-101 Boog frame FE360 Poedercoat 199-111 Polyester kappen Polyester 199-221 L klem SS304 Thermisch verzinkt + poedercoat 199-231 Stelplaatje FE360 Thermisch verzinkt 199-320 UFO camera schijf Electronics 199-501 Kunstgras vloer...
Page 41
Pla e schroevendraaier Stanley mes Bezem Evenaar Kruis schroevendraaier Vulzand #30 Silica rond 0.2-1mm #30 Silica rond 0.008-0.04” Grondmontage Sneldrogend beton (C20/C25 NEN 800 kg 1764 lbs -EN206-1/-8005) Opbouw montage Klopboor Betonfrees Chemisch anker (4000N) bijv. Hil HIT 170 met 8.8 anker M20 (in combina e met >...
Page 42
van 2 meter van de stroomkabel. De kabel dient ten minste • Bepaal het maaiveld (nul-niveau) van de ondergrond. Dit 60cm diep te liggen. is het referen epunt voor alle andere afme ngen WARNING De stroomkabel naar het toestel dient te •...
Page 43
D.9 Draai alle bout/moer verbindingen vast in de top en aan NOTICE Zorg ervoor dat de plus- en minpolen op de de basis van het boogframe. juiste manier aangesloten worden. D.10 Verbindt de polyester kappen ook bovenin aan het D.14 Monteer de zijkappen. frame.
Page 44
• Behandel de polyester kappen twee keer per jaar met • Als onderdelen beschadigd zijn of ontbreken, moet het auto wax (turtle wax) voor een blijvend mooi oppervlak. product worden losgekoppeld en moeten de onderdelen worden gecorrigeerd, gerepareerd of vervangen om •...