HSU-24C03/Z HSU-24H03/Z Introduction 1. Introduction 1.1 Safety Cautions Be sure to read the following safety cautions before conducting repair work. The caution items are classified into “Warning” and “Caution”. The “Warning” items are especially important since they can lead to death or serious injury if they are not followed closely. The “Caution” items can also lead to serious accidents under some conditions if they are not followed.
HSU-24C03/Z HSU-24H03/Z Introduction Warning Do not repair the electrical components with wet hands. Working on the equipment with wet hands can cause an electrical shock. Do not clean the air conditioner by splashing water. Washing the unit with water can cause an electrical shock.
HSU-24C03/Z HSU-24H03/Z Introduction 1.1.3 Inspection after Repair Warning Check to make sure that the power cable plug is not dirty or loose, then insert the plug into a power outlet all the way. If the plug has dust or loose connection, it can cause an electrical shock or fire. If the power cable and lead wires have scratches or deteriorated, be sure to replace them.
HSU-24C03/Z HSU-24H03/Z Introduction 1.1.4 Using Icons Icons are used to attract the attention of the reader to specific information. The meaning of each icon is described in the table below: 1.1.5 Using Icons List Icon Type of Information Description A “note” provides information that is not indispensable, but may Note: Note nevertheless be valuable to the reader, such as tips and tricks.
24C03/Z HSU-24H03/Z 4. Printed Circuit Board Connector Wiring Diagram 4.1 Indoor Unit Connectors PCB1 control PCB 1) CN1 connector for ION unit 2) CN2 connector for DC fan motor 3) CN4 connector for N in the terminal block 4) CN7 connector for louver motor 5) CN8 connector for ambient temp.
Page 17
Note: Sequence of defrosting actions: 9minutes ompressor Four-way valve Outdoor fan 1min 1min 5.1.7 Freezing prevention function Under refrigerating and dehumidifying state, the air conditioner will control the outdoor fan as per the temperature Tp of the indoor coil pipe according to the following conditions: Compressor ,outdoor fan Zone of return deference OFF after 5 minutes...
b.After setting the sleeping function, the heating mode will run as per the following rules: 1 hour 1 hour 3hours 3hours T( ) Ts-2 Ts-3 Ts-4 t(hour) Sleep As shown in the above diagram, after running for 1 hour under refrigerating mode and dehumidification mode, the setting temperature will increase 1 ;...
HSU-24C03/Z HSU-24H03/Z System Configuration 6. System Configuration 6.1 System Configuration After the installation and test operation of the room air conditioner have been completed, it should be operated and handled as described below. Every user would like to know the correct method of operation of the room air conditioner, to check if it is capable of cooling (or heating) well, and to know a clever method of using it.In order to meet this expectation of the users, giving sufficient explanations taking enough time can be said to reduce about 80% of the requests for servicing.
HSU-24C03/Z HSU-24H03/Z System Configuration 6.2 Instruction Cautions Disposal of the old air conditioner Safety Instructions and Warnings Before disposing an old air conditioner that Before starting the air conditioner, read the goes out of use, please make sure it's inop- information given in the User's Guide caref- erative and safe.
HSU-24C03/Z HSU-24H03/Z System Configuration Cautions 7. The appliance is not intended for use Do not obstruct or cover the ventilation by young children or infirm persons grille of the air conditoner.Do not put fingers without supervision. or any other things into the inlet/outlet and swing louver.
HSU-24C03/Z HSU-24H03/Z System Configuration Cautions Safety Instruction Please read the following Safety Instructions carefully prior to use. The instructions are classified into two levels, WARNING and CAUTION according to the seriousness of possible risks and damages as follows. Compliance to the instructions are strictly required for safety use.
Page 34
HSU-24C03/Z HSU-24H03/Z System Configuration Cautions WARNING When abnormality such as burnt-small found, Use an exclusive power source with a immediately stop the operation button and circuit breaker contact sales shop. STRICT ENFORCEMENT Connect power supply cord Use the proper voltage Do not use power supply cord to the outlet completely extended or connected in halfway...
Page 35
HSU-24C03/Z HSU-24H03/Z System Configuration...
Page 52
HSU-24C03/Z HSU-24H03/Z Service Diagnosis 7.service diagnosis 7.1.caution for diagnosis 1. The operation lamp flashes when any of errors is detected. 2. when a protection device of the indoor or outdoor unit is activated or when the thermistor malfunctions, disabling equipment operation. 7.2.Problem Symptoms and Measures Sympt m Check Item...
Page 53
HSU-24C03/Z HSU-24H03/Z Service Diagnosis 7.3.2Thermistor or Related Abnormality (indoor unit) QGRRU 'LVSOD\ Power timer operate 0HWKRG RI 0DOIXQFWLRQ the temperatures detected by the thermistors are used to determine hermistor errors 'HWHFWLRQ 0DOIXQFWLRQ when the thermistor input is more than 4.92V or less than 0.08V during compressor 'HFLVLRQ operation.
HSU-24C03/Z HSU-24H03/Z Service Diagnosis 7.3.3.Fan Motor(DC Motor) or Related Abnormality QGRRU 'LVSOD\ Code indication Power timer operate flash 0HWKRG RI The rotation speed detected by the Hall IC during fan motor operation is used to determine 0DOIXQFWLRQ abnormal fan motor operation 'HWHFWLRQ 0DOIXQFWLRQ when the detected rotation feedback signal don’t received in 2 minutes...
Page 55
HSU-24C03/Z HSU-24H03/Z Service Diagnosis Turn off power supply and rotate fan by hand Does rotate Replace fan motor smoothly? Check output motor connector and Turn power ON and operate fan Turn off power supply and disconnect Does it rotate? fan motor connector,then turn power Check output of fan motor connector Check rotation pulse input (pins 4-7).