Haier HSU-24C03/Z - annexe 2 Operation Manual
Split type room air conditioner
Hide thumbs
Also See for HSU-24C03/Z - annexe 2:
- Manual (8 pages) ,
- Service manual (90 pages) ,
- Operation manual (32 pages)
Subscribe to Our Youtube Channel
Related Manuals for Haier HSU-24C03/Z - annexe 2
Summary of Contents for Haier HSU-24C03/Z - annexe 2
-
Page 1: Operation Manual
SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL Please read this operation manual before using the air conditioner. No.0010554541... -
Page 2: Table Of Contents
Contents Cautions Parts and functions Operation 5-12 Maintenance 13-17 Trouble shooting... -
Page 3: Cautions
Minimum: D.B / W.B C/-8 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F 3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V. -
Page 4: Parts And Functions
Parts and Functions Signal Receiving windows Running Indicator Timer Mode Indicator Power Indicator... -
Page 5: Clock Set
Clock set Used to reset the controller back to normal condition. When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Press to set correct time. -
Page 6: Parts And Functions
The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. -
Page 7: Operation
When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press... - Page 8 All indicators on indoor unit go out. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed.(TIMER ON/OFF needs reelecting)
-
Page 9: Cool,Heat And Dry Operation
DRY mode. regardless of FAN setting. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. - Page 10 Operation...
-
Page 11: Timer Operation
TIMER Operation Set Clock correctly before starting Timer operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. - Page 12 Follow the same procedures in "Time setting for TIMER ON". (6) Time confirming for TIMER OFF After time setting, press SET button to confirm, "OFF" stops flashing Time displayed: Unit stops at X hour X min. To cancel TIMER mode...
- Page 13 Operation...
- Page 14 Operation Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. ON/OFF TEMP In COOL mode MODE One hour after SLEEP mode starts, temp. will become 1 C higher than temp.
-
Page 15: Maintenance
Maintenance... - Page 16 Maintenance...
-
Page 17: Replacement Of Air Purifying Filter
Install air purifying filter (Necessary installment) Please replace the air Purifying Filter when color of the filter become same level of sample attached in the indoor unit. Please replace the air Purifying Filter in 3-6 months as standard.
Need help?
Do you have a question about the HSU-24C03/Z - annexe 2 and is the answer not in the manual?
Questions and answers