Page 1
CABINET TYPE AIR CONDITIONER Operation & Installation Manual No.0010578212 Please read this operation manual before using the air conditioner. Please keep this manual carefully and safely. ON/OFF MODE HEALTH TEMP+ TEMP- HEALTH HUMI TIMER TEMP SLEEP AP482AKEAA AP602AKEAA...
Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier. Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Do not put fingers or any other things into the inlet/outlet and swing louver. Do not allow children to play with the air conditioner. In no case should children be allowed to sit on the outdoor unit. Specifications The refrigerating circuit is leak-proof.
Parts MODE HEALTH TEMP+ TEMP- HEALTH ON/OFF HUMI TIMER TEMP SLEEP Outdoor unit Inlet grill Outlet grill MODE ON/OFF HUMI TEMP I n d o o r u n i t Outlet grill Operation panel Inlet grill Air filter [inside the unit] HEALTH TEMP+ TEMP-...
Page 6
Parts Manual Operation TEMP HEALTH MODE SLEEP SWING CLOCK TIMER HEAT LIGHT LOCK RESET Power ON/OFF Used for unit start and stop. MODE Used to select AUTO run, COOL, DRY, FAN and HEAT operation. CLOCK Used to set correct time. Note: These models don't have the following related display and function For some air conditioners , the function For cooling only unit, there is no functions related to heat.
Operation Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM"or "PM" flashes. Press to set correct time. Each press will increase or decrease 1 min . If the button is kept pressed, time will change quickly.
Page 8
Operation Control panel Remote-control unit TEMP HEALTH MODE SLEEP SWING CLOCK TIMER HEAT RESET LIGHT LOCK Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press, operation mode changes as follows: Note: During Auto run operation, temp.
Remote controller Control panel Air conditioner will run at the selected fan speed. 4. Unit stop Press ON/OFF button to stop unit. About FAN mode When the air conditioner runs in FAN mode,it is not possible to select AUTO FAN or to set temperature.
Operation Swing louvers (Vertical louvers) (Horizontal louvers) TEMP HEALTH MODE SLEEP SWING CLOCK TIMER HEAT RESET LIGHT LOCK 2.Up & down air direction Press the up & down button once ,the LCD aiflow direction will display as follows: Cooling/Dehumification/airflow : Position 1 Remote controller: Position 5...
Before using this function, the clock must be set. After the unit's start, set running mode and then press SLEEP button once to make the air conditioner have the previous-set sleep time (first power-on is "1h"). The sleep symbol will appear. Press time button : you can choose the time in 1~8 hours.
Operation Manual Operation Control panel Remote controller TEMP HEALTH MODE SLEEP SWING CLOCK TIMER HEAT LIGHT LOCK RESET Hints: After replacing batteries or if a power failure occurs, TIMER setting must be reset. Remote controller has memory function. When you use TIMER mode next time, just press SET button after mode selection if timer setting is the same as the previous one.
Page 13
Operation Manual Operation Control panel Remote controller TEMP HEALTH MODE SLEEP SWING CLOCK TIMER HEAT LIGHT LOCK RESET 5.Timer setting for TIMER OFF Press time buttons and follow the same procedures in " Time setting for TIMER ON" 6.Time confirming for TIMER OFF After time setting, press SET button to confirm time.
When cut off the power and restart the power ,the room temp. will be displayed after full screen display lasting 5 seconds .Press the panel button or remote control ,the air conditioner will send out music sound . TEMP LCD bright...
Operation hints Unit operation Protection devices inside the unit will activate to stop unit operation, when ambient temp. is extremely low or high. When unit is running under high humidity in cooling or dehumidifying mode, condensate might appear at outlet grill. 3-min delay protection Unit will not restart until 3 min have elapsed for the protection of the unit.
Energy saving Keep proper room temp. Too cold or too warm is no good to your health, and power consumption will be increased as well. Air filter should be periodically cleaned If air filter is clogged: It will cause poor cooling and heating efficiency, higher power consumption and even problem may occur.
Maintenance Disconnect power supply Don't splash water directly on indoor unit. This could be very dangerous Air filter cleaning Pull it out from top as shown in Fig. Use water or vacuum cleaner to clean it. If it is extremely dirty, wash it with neutral detergent or soap water.
Clean it with warm and wet cloth or with neutral detergent, then wipe it dry with clean and soft cloth. If air conditioner is very dirty, clean it with cloth soaked in neutral detergent,then wipe off the detergent with clean water.
Trouble shooting Followings are not problems Sound of water flowings are not problems. Sound of cracking is heard. Smells are generated. During operation, white fog or steam comes out of indoor unit. In cooling operation, unit switches to fan operation. Unit will not restart after stop.
Water comes out in cooling/dry operation. Operation is abnormal or sound is heard. If the fuse on PC board is broken please change it with the type of T3.15A/250VAC. Air conditioner won't start. Is city power supply normal? Power failure?
The power cable should be over H07RN-F 5G 4.0mm Air conditioner must use an exclusive line (over 30A) When installation air conditioner in a wet place, try to use a circuit breaker against current leakage. For installation in other places, use circuit breaker as far as possible.
Installation procedures Display of whole unit Try to bring the packed unit to the installation place. When it is inevitable to unpack the unit, be careful not to damage the unit. Wrap it with nylon etc. After unpacking, be sure to put it with the front side of the unit facing up. Note: When delivering, don't hold plastic parts like inlet and outlet grill etc.
Installation procedures Installation of indoor unit Selection of installation place Place where it is easy to route drainage pipe and outdoor piping. Place away from heat source and with less direct sunlight. Place where cool and warm air could be delivered evenly to every corner of the room. Place near power supply socket.
Installation procedures Piping connection Connecting method Apply refrigerant oil at half union and flare nut. To bend a pipe, give the roundness as large as possible not to crash the pipe. When connecting pipe, hold the pipe centre to centre then screw nut on by hand,refer to Fig.
Page 27
Installation procedures Arrangement of drain hose Drain hose shall be placed in under place. There should be a slope when arrange drain hose. Avoid up and down waves in drain hose. Indoor unit Slope Good If humidity is high, drain pipe( especially in room and indoor unit ) must be covered with insulation material.
Pull the cable gently to make sure it is tight. Replace cover after wiring. Note: When connecting indoor and outdoor wire, check the number on indoor and outdoor terminal blocks.Incorrect wiring may damage air conditioner's controller or cause operation failure. AP482AKEAA AP602AKEAA 1 2 3...
Others 1. Pipe cutting and flaring Be sure to carry out deburring after pipe cutting with a pipe cutter. Insert flaring tool to make a flare. Correct Lean Damaged flare Crack Pipe dia. Liquid pipe 9.52mm (3/8") Gas pipe 19.05mm (3/4") 2.Installation inspection and test run: Please operate unit according to this Manual.
Page 30
HAIER GROUP Qingdao Haier Air Conditioner Electric Co., Ltd. Address: Haier Garden, Qianwangang Road, Economic Development Zone, Qingdao, Shandong 266500, P.R.China Web Site: http://www.haier.com...