GBC USP 13 Operator's Manual
  1. Manuals
  2. Brands
  3. GBC Manuals
  4. Industrial Equipment
  5. USP 13
  6. Operator's manual

GBC USP 13 Operator's Manual

Universal speed punch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USP 13
UNIVERSAL SPEED PUNCH
Operator Manual

Advertisement

Table of Contents
loading

Related Manuals for GBC USP 13

Summary of Contents for GBC USP 13

  • Page 1 USP 13 UNIVERSAL SPEED PUNCH Operator Manual...

  • Page 2: Table Of Contents

    USP 13 UNIVERSAL SPEED PUNCH Operator Manual Table of Contents Operating Instructions Service and Maintenance Agreement Selecting Knife Set Up Installation of Punching Die Set Up Instructions Quick Reference Instructions Maintenance Instructions General Rules for Grinding Pins Options and Accessories...

  • Page 3: Usp 13

    USP 13 Universal Speed Punch Operating Instructions The Universal Speed Punch from With proper maintenance the GBC Automated Finishing Division Universal Speed Punch will provide is specially designed to punch troublefree, continuous operation for various weight paper sheets and many years.

  • Page 4: Service And Maintenance Agreement

    A GBC Authorized Technician must perform all service and maintenance unless it is operator maintenance in accordance with the USP 13 Operator Manual. Use of the USP 13 in any manner not in accordance with the GBC USP 13 Operator Manual is not recommended and may void your warranty or maintenance contract Trained operators and regular operator maintenance of the USP 13 can optimize performance and minimize service calls.

  • Page 5: Selecting Knife Set Up

    SELECTING KNIFE SET-UP Turn power off. Cycle the machine with the hand wheel until the claw reaches between 10 and 11 o’clock. (Figure 2) Cam #115 sets when the separating knife will go into the stack. Adjust the cam so that the tip of the knife is about 1/8”...

  • Page 6: Installation Of Punching Die

    USP 13 Installation of Punching Dies Using Quick Release Die Clamp Assembly PULL ROD PULL ROD ADJUSTING NUT THESE SURFACES SHOULD BE FLUSH OVER THE LENGTH OF THE PUNCHING PUNCHING DIE ADJUSTING NUT LOWER DIE SUPPORT Figure 5 Figure 6 When installing a punching die, be sure that the lower die support is wiped clean of dirt and paper chips.

  • Page 7: Set Up Instructions

    USP 13 SET-UP INSTRUCTIONS: After the punching die is properly installed, position the SETTING REGISTRATION back gauge rail (#108, Figure 7) slightly ahead of the Loosen locking bolt (S40) under front bearing block punch die back gauge so that a piece of paper can slide (#93, Figure 9) prior to setting registration.
  • Page 8 REAR JOGGER Place a sheet of paper against pusher (#111) in its home position (rear). Install the three paper support straps (#127 & #83, Figure 10) 1” away from the edge of the paper. Straps must be on top of transfer belts. Cycle the machine by hand until the pusher has pushed the paper to its furthest point.
  • Page 9 Position front (#49) and rear (#56 & #48) supply stack guides so that the posts clear the paper stack by about 1/16”. A stack of 2 to 3 inches is required. Locate adjustable stack guide post (#59) so that the post is in line with the separating knife. (Figure 13).

  • Page 10: Quick Reference Instructions

    USP 13 Universal Speed Punch QUICK REFERENCE INSTRUCTIONS 1. DIE REPLACEMENT BLOCK UP DIE WITH STICK PROVIDED LOWER DIE CLAMP STICK REMOVE DIE CLAMPS - FRONT & REAR REMOVE BOTTOM BOLTS RELEASE CLAMP - RELAX PRESSURE WITH HAND WHEEL SLIDE DIE OUT...

  • Page 11: Maintenance Instructions

    USP 13 Universal Speed Punch MAINTENANCE INSTRUCTIONS It is recommended that the machine be lubricated IMPORTANT! once every two weeks. Lubricate by putting a few drops of machine oil in the lubricating holes, which are marked All punching tools should be lubricated daily.

  • Page 12: General Rules For Grinding Pins

    GENERAL RULES FOR GRINDING PUNCHING PINS OF PUNCHING TOOLS Sharp punching tools are necessary to produce clean holes, which are essential to maintain high binding IMPORTANT production and the prevention of premature wear of All punching tools must be sharpened every 100 hours punching tools.

  • Page 13: Options And Accessories

    USP 13 OPTIONS & ACCESSORIES The Universal Speed Punch comes equipped with all the tools and parts necessary to run standard size sheets of paper. Additional accessories are included to run some of the more non-standard sizes of paper. They include: 1.
  • Page 15 016509000 LONG SMALL ROLLER ASSEMBLY The Long Small Roller Assembly is used when the standard Large Roller Assembly does not allow enough reach to grab a lift of paper when it is fully jogged.
  • Page 17 General Binding Corporation Northbrook, Il 60062-4195 http://www.GBC.com PN 0165999900 Rev B...

Table of Contents