Troubleshooting - Steinbach Speedcleaner APPcontrol Instruction Manual

EN
▶
6
7 Stop sign
8 mode
9 Auto play or stop
Attention："▶"&"◀"need to be pressed constantly
Warning
Caution: Before removing the cleaner from
the pool, make sure that the electricity is fully
switched off.
Preparation
Care and maintenance
The cleaner turns itself off automatically after a cleaning cycle. Unplug
the mains cable, gently pull the cable, and lift the cleaner out of the
water using the ring on the clamp nut.
Caution:
When lifting the cleaner out of the water, you must ensure that the
cleaner does not hit the side of the pool wall, otherwise you may dam-
age both the cleaner and the liner. 
Before the cleaner clears the surface of the water, it must be held
there for 10 to 15 seconds, so that most of the water can flow out of
the water outlet into the pool. Only then should you put the cleaner on
the edge of the swimming pool.
Clean the filter tray
Fig. 11

Lift the tray handle up

Take out the filter tray

Slide the clip to open the tray

Take the slides off

Clean the tray
Put the filter tray back
Machine have a slide way to lead filter tray back into the cleaner, and
clip the handle in position perfectly.
Hints and tips
Every time the cleaner is taken out of the water, the filter cleaner must
be cleaned.
Make sure the pH value of the water is between 7.0 and 7.2.
Make sure the water temperature is between 10°C and 32°C.
After every clean, the drive train must be thoroughly cleaned to en-
sure the same level of grip on the next clean.
Speedcleaner APPcontrol | 2017_V1
Manual right turn
Manual stop machine
●Pool floor mode
●Pool wall mode
●One floor one wall mode
●Three floor one wall mode
●Auto Play: working as selected
mode
●STOP: stop working automatically
.
Fig.12
After pressing the "Power Off" button, the "Power On" button cannot
be pressed for 30 seconds.
We recommend keeping the cleaner between 10°C and 32°C in a
shaded, well ventilated place. Avoid direct sunlight at all times.
We recommend attaching the operating unit with a safety rope, to
avoid any risk of the power pack being pulled into the pool.
Before use, please read the instructions relating to trouble-shooting
thoroughly.
Trouble shooting
Indicator
1H flash quickly with
buzz
All lights flash quickly
with buzz
1H+2H+3H flash quick
with buzz
ALL+1H flash
with buzz
WALL+2H quick with
buzz
Diagnose
FLOOR+3H
flash quick with buzz
ALL+WALL+1H+2H
flash quick with buzz
ALL+WALL+FLOOR
flash quick with buzz
WALL+FLOOR+2H+3H
flash quick with buzz
WALL flash quick with
buzz
Guarantee
A guarantee will only be undertaken by the manufacturer with regard
to safety and reliability under the following circumstances:
 The floor vacuum cleaner is used in accordance with the guidance
in the instruction manual.
 Only original replacement parts were used in any repairs (Parts
liable to wear and tear are not covered by guarantee).
Meaning Suggestion
Put machine
back
Machine water or wait
out of wa- until ma-
ter chine restart
automati-
cally
Stop ma-
Control chine
box over contact after
load sale service
person
Stop ma-
chine
Seal box
contact after
leaking
sale service
person
Stop ma-
quick Pump over chine check
load the impeller
and pump
Stop ma-
Walking chine check
motor 1 belt and
over load transmission
system
Stop ma-
Walking chine check
moter 2 belt and
over load transmission
system
Stop ma-
Cleaner
chine
present
contact after
abnormal-
sale service
voltage
person
Check
cable
between
Abnormal cleaner and
communi- control box
cation or contact
the after
sale service
person
Machine Stop ma-
out of wa- chine restart
ter and machine
could not manually af-
restart ter cleaner
sink
Machine Turn over
turned machine
over manually
Page 9 of 60
into
the