Page 1 Portégé User’s Guide If you need assistance: ® InTouch Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see TOSHIBA 4010 Series ® Chapter 10 page 197. C6614-1002M2...
Page 2 If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.
Page 3: Fcc Notice
: Only peripherals complying with the FCC Class B limits may be attached to this computer. Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's serial port, parallel port, monitor port, USB port, PS/2 microphone jack.
Page 4: Type Of Service
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
Page 5: If Problems Arise
FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba.
Page 6: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The Toshiba Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 7: Wireless Lan And Your Health
Regulatory Information The Toshiba Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 8: Interference Statement
The radiated output power of the Toshiba Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the Toshiba Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. The distance between the antennas and the user should not be less than 20.0 cm.
Page 9 Approved Countries for use This equipment is approved to the radio standard by the countries in Fig.1. Australia Canada France Iceland Japan New Zealand Portugal Switzerland Fig. 1. Caution: Do not use this equipment except in the countries in Fig.1. CD-ROM, DVD-ROM, DVD-ROM/CD-RW Safety Instructions The CD-ROM, DVD-ROM, and DVD-ROM/CD-RW drives employ a...
Page 10: Export Administration Regulation
This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 11 PS/2 is a registered trademark of International Business Machines Corporation. Wi-Fi is a trademark of the Wireless Capability Ethernet Alliance. Bluetooth is a trademark owned by its proprietor and used by Toshiba under license. All other brand and product names are trademarks or registered trademarks...
Page 12 Computer Disposal Information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.
Page 13: Table Of Contents
Contents Introduction ...23 This guide ... 23 Safety icons ... 24 Other icons used... 25 Other documentation ... 25 Service options ... 26 Chapter 1: Finding Your Way Around ... 27 Making sure you have everything ... 27 Finding where everything is located... 27 Front with the display panel closed ...
Page 14 Turning on the power... 55 Using the AccuPoint II ... 56 Setting up your software... 58 Registering your computer with Toshiba ... 59 Customizing your computer’s settings... 60 Powering off the computer ... 61 Closing the display panel ... 61 Different ways to turn the computer Caring for your computer...
Page 15 Using the keyboard ... 65 Character keys ... 66 Making your keyboard emulate a full-size keyboard ... 66 Ctrl, Fn, and Alt keys ... 67 Function keys... 67 ® Windows special keys... 68 Overlay keys ... 68 Starting a program... 70 Saving your work ...
Page 16 Contents Toshiba’s online resources... 86 Chapter 4: Mobile Computing ... 87 Toshiba’s energy-saver design ... 87 Running the computer on battery power ... 87 Maximizing battery life... 88 Using additional batteries ... 89 Battery safety precautions... 89 Charging batteries... 90 Charging the batteries...
Page 17 Using the optional USB external diskette drive with a PC Card ... 105 Using a keyboard with the Advanced Port Replicator... 106 Connecting a keyboard to the Advanced Port Replicator... 106 Making your external keyboard emulate the Fn key ... 106 Using a mouse with the Advanced Port Replicator...
Page 18 Contents Using Standby or Hibernate Removing an SD card ... 118 Chapter 6: Enhancing Productivity... 119 Windows Personalizing your desktop... 120 Customizing the taskbar ... 120 Bringing the world to your desktop... 121 Changing desktop and browsing style ... 122 Personalizing individual windows ...
Page 19 Using Turn Off or Shut down ... 137 Turning off more quickly ... 138 Starting again after Turn Off or Shut down ... 141 Using Hibernation ... 141 Enabling the Hibernation command ... 141 Going into Hibernation mode ... 143 Going into Hibernation mode more quickly...
Page 20 Contents Launching an Internet browser from WinDVD ... 172 Getting Help ... 172 Exiting WinDVD ... 172 Chapter 8: Toshiba Utilities ... 173 Fn-esse ... 173 Starting Fn-esse... 174 Assigning a key to a program or document ... 175 Viewing existing key assignments... 177 Changing or removing Hotkey utility ...
Page 21 Deleting the hard disk drive user password ... 195 Chapter 10: If Something Goes Wrong ... 197 Problems that are easy to fix ... 197 Problems when you turn on the computer... 199 The Windows Using Startup options to fix problems ... 201 Internet problems ...
Page 22 Contents Before you call ... 229 Contacting Toshiba ... 229 Other Toshiba Internet Web sites ... 230 Toshiba’s worldwide offices ... 231 Appendix A: Hot Keys ... 235 Volume Mute... 235 Password security ... 235 Without a password ... 235 With a password ...
Page 23: Introduction
Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. You will find that your Microsoft operating system is already installed on your computer. It offers exciting features and easy Internet access.
Page 24: Safety Icons
Introduction Safety icons Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows: DANGER: This icon indicates the existence of a hazard that could result in death or serious bodily injury if the safety instruction is...
Page 25: Other Icons Used
Guides for other programs that may come preinstalled on your computer and for additional programs on your Recovery CDs. ❖ Accessories information, which lists accessories available from Toshiba and explains how to order them. ❖ The Microsoft which explains the features of the operating system. Other documentation ®...
Page 26: Service Options
Introduction Service options Service options Toshiba offers a full line of service options built around its SelectServ Toshiba's Web site at toshiba.com. If you have a problem or need to contact Toshiba, see Something Goes Wrong” on page warranty programs. For more information, visit 197.
Page 27: Chapter 1: Finding Your Way Around
If any items are missing or damaged, contact your authorized Toshiba representative or your network administrator. Finding where everything is located The next few pages take you on a guided tour of your...
Page 28: Front With The Display Panel Closed
Finding Your Way Around Finding where everything is located Front with the display panel closed Display latch—Sliding the display latch opens the computer display panel. For more information, see display panel open” on page 31 System indicator panel—The system indicator panel is made up of several status lights that provide information about various system functions.
Page 29: Right Side
Finding Your Way Around Finding where everything is located megabits per second (Mbps) between the computer and an external device, such as a video camera. USB ports—The two USB (Universal Serial Bus) ports provide a connection for USB peripherals. USB is a single- cabling and connection standard that supports a data transfer rate of up to 12 megabits per second (Mbps).
Page 30: Left Side
Finding Your Way Around Finding where everything is located Left side Cooling vent Speaker Security lock slot DC-IN PC Card slots Security lock slot—Attaching an optional PORT- Noteworthy lets you anchor your computer to a large, heavy object such as your desk. For more information, see lock”...
Page 31: Front With The Display Panel Open
Microphone jack—The 3.5 mm microphone jack lets you connect an external monaural microphone or other audio input device. Connecting a microphone or other device to this jack automatically disables the internal microphone. Headphone jack—The 3.5 mm headphone jack lets you connect stereo headphones or other audio output devices.
Page 32 See AccuPoint II” on page Programmable buttons II pointing device—This device combines the Screen Keyboard indicator panel TOSHIBA Console button Wireless antenna on/off switch “Using the “Turning on the power” “Using the...
Page 33 (for example, aboard commercial aircraft), you should turn the wireless antenna switch off. TOSHIBA Console button—Allows quick access to various functions. Keyboard indicator panel—These lights provide information about various keyboard functions. See “Keyboard indicator panel”...
Page 34: Underside
Finding Your Way Around Finding where everything is located Underside Expansion port Slim SelectBay release latch Battery module Expansion port—Lets you connect to a port replicator. These devices provide additional ports including a serial port, parallel port and PS/2 port. For more information, see an expansion device”...
Page 35: Indicator Panels
Indicator panels Two sets of indicator panels, the system indicator panel and the keyboard indicator panel, display the current state of your system. System indicator panel This panel is located on the top leading edge of the display. AC power light—Glows green when the computer is connected to an AC power source.
Page 36: Keyboard Indicator Panel
Finding Your Way Around Indicator panels Hard disk drive light—Flashes to indicate that the hard disk is currently in use. Slim SelectBay activity light—Indicates the status of a module in the Slim SelectBay, if installed. Wireless indicator light—If your computer is fitted with an optional wireless communication system, either 802.11b (now referred to as Wi-Fi—wireless fidelity) or Bluetooth, this indicator light glows amber when the wireless on/off...
Page 37 Finding Your Way Around Indicator panels printed on the top of the key. For more information, see “Using the overlay to type numeric data” on page...
Page 38: Chapter 2: Getting Started
Chapter 2 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and location Creating a computer-friendly environment Place the computer on a flat surface that is large enough for...
Page 39: Keeping Yourself Comfortable
AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact your Toshiba service representative or your network administrator. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
Page 40 Getting Started Selecting a place to work Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries: ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching.
Page 41 comfortably with your shoulders relaxed and your forearms parallel to the floor. If you are using a conventional chair: ❖ Your knees should be slightly higher than your hips. If necessary, use a footrest to raise the level of your knees and ease the pressure on the back of your thighs.
Page 42: Precautions
Getting Started Precautions Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ❖...
Page 43: Setting Up Your Computer
❖ Scan all new files for viruses. This precaution is especially important for files you receive via diskette or email, or download from the Internet. Setting up your computer Your computer contains a rechargeable main battery that needs to be charged before you can use it. To use external power or to charge the battery, you must attach the AC adapter.
Page 44: Installing Additional Memory (Optional)
BIOS memory check. An error message may appear. If this occurs, contact Toshiba’s support center. See need further assistance” on page Since your computer was built to order, it should have enough memory to run your current applications.
Page 45 Open the display panel and remove the panel that contains the Power and TOSHIBA Console buttons. CAUTION: When removing the computer’s power and TOSHIBA Console button panel to install additional memory, be careful not to damage the display or circuit board.
Page 46 Getting Started Setting up your computer Removing the left keyboard screw Locate and remove the screws that hold the keyboard in place. Removing the right keyboard screw...
Page 47 Lift the keyboard and place it face down on the palm rest of the computer. Lifting off the keyboard The memory module expansion slots Getting Started Setting up your computer...
Page 48 Getting Started Setting up your computer CAUTION: Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer.
Page 49: Removing A Memory Module
Replace the keyboard and the screws. Replace the panel that contains the Power and TOSHIBA Console buttons. Press hard on the keyboard panel to snap it into place. Restart the computer. When you turn on the computer, it automatically recognizes the additional memory.
Page 50: Connecting An External Usb Mouse
Getting Started Setting up your computer Connecting an external USB mouse You may want to use a mouse instead of the computer’s built- in pointing device, the AccuPoint II. You can attach an external mouse to one of the computer’s USB ports, provided the mouse is USB-compatible.
Page 51: Connecting The Modem
See your printer documentation for additional configuration steps, or see Connecting the modem Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet. ❖ Communicate with your office’s local area network (LAN), or a larger corporate wide area network (WAN).
Page 52: Connecting To A Power Source
Getting Started Setting up your computer Connecting to a wall jack CAUTION: The modem is designed for use with a standard analog telephone line. Never connect the modem to a digital telephone line. A digital line will damage the modem. Now you’re ready to send a fax or use the modem to connect to an online service or the Internet.
Page 53 Connecting to an AC outlet The AC adapter enables you to power the computer from a wall outlet and to charge the computer’s main battery. DANGER: Hold the power cable by its plug when you connect/ disconnect it. Do NOT pull the cable itself. Doing so may damage the power cable and result in a short circuit or electric shock.
Page 54: Using The Main Battery
Doing so may cause an electric shock. CAUTION: Use of the wrong AC adapter could damage your computer. Toshiba assumes no liability for any damage in such cases. Never pull directly on the power cable to unplug it. Hold the power plug when removing the cable from the outlet.
Page 55: Connecting Other External Devices
Connecting other external devices For more information on attaching other external devices, such as a keyboard and diskette drive, see the “Expansion Options” chapter on page 103. Using the computer for the first time For information on connecting devices, see computer”...
Page 56: Using The Accupoint Ii
Getting Started Using the computer for the first time Press and hold in the power button until the on/off light on the system indicator panel glows green—about one second. CAUTION: Never turn off the computer while any of the drives is in use.
Page 57 Using the computer for the first time page 50. For information on connecting a mouse using the Advanced Port Replicator, see Advanced Port Replicator” on page To move the cursor, gently push the pointing device in the direction you want the cursor to move. Pushing harder on the pointing device moves the cursor faster.
Page 58: Setting Up Your Software
Getting Started Using the computer for the first time Primary and secondary control buttons The control buttons are used like the buttons on a mouse. The primary control button corresponds to the left mouse button. To double-click, press the primary button twice in rapid succession.
Page 59: Registering Your Computer With Toshiba
Toshiba warranty worldwide at no charge to you. You can register your computer with Toshiba by double- clicking the icon on your desktop or by mailing the registration card that may ship with your computer.
Page 60: Customizing Your Computer's Settings
You may also wish to customize your power usage settings. For more information, see automatically” on page settings you can choose. See ® XP Professional Add Printer “Turning off the display 97. There are additional custom “Toshiba Utilities” on page 173.
Page 61: Powering Off The Computer
Powering off the computer It’s a good idea to power off your computer when you are not using it for a while. If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery.
Page 62: Different Ways To Turn The Computer On And Off
CAUTION: Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer. “Toshiba 185. “Power Management” on “Using Hibernation” on page 141 145.
Page 63: Moving The Computer
To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your network administrator for suggestions for appropriate cleaning products. Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the drive-in-use light stops glowing) and all external peripheral cables are disconnected.
Page 64: Chapter 3: Learning The Basics
Chapter 3 Learning the Basics This chapter lists computing tips and provides important information about the system’s basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Page 65: Using The Keyboard
❖ Back up your files to diskettes (or other removable storage media) on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Page 66: Character Keys
Learning the Basics Using the keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page. ❖...
Page 67: Ctrl, Fn, And Alt Keys
Your computer’s keyboard has only one Most of the time this doesn’t matter. However, some programs assign separate functions to the right and left keys, or to the regular and numeric pad the full-sized keyboard. Using the these separate keys, as follows: ❖...
Page 68: Windows ® Special Keys
Learning the Basics Using the keyboard Hot keys When used in combination with the Fn key, function keys marked with icons run programmed functions specific to your computer. For more information, see page 235. ® Windows special keys ® Windows special keys Your computer’s keyboard has two keys, located at the top- right of the keyboard, that have special functions in the...
Page 69 ∗ & Home Numeric and cursor control overlay Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press simultaneously. The numeric mode light glows when the numeric overlay is on.
Page 70: Starting A Program
Learning the Basics Starting a program To turn off the numeric overlay, hold down the press again. The numeric mode light on the keyboard indicator panel goes out. Using the cursor control overlay To turn on the cursor control overlay, press simultaneously.
Page 71: Saving Your Work
❖ Use the Start menu ❖ Use Windows ❖ Use the Run dialog box For more information, see Help and Support in the Start menu. Saving your work Before you turn off the computer, save your work to the hard disk drive or a diskette.
Page 72: Printing Your Work
Learning the Basics Printing your work Printing your work Verify that the Windows your printer as described in TECHNICAL NOTE: You only need to set up the printer the first time you connect it. If you use more than one printer or are changing printers, you will need to set up the operating system to run with the additional printer(s).
Page 73: Copying Documents To A Diskette
Copying documents to a diskette Diskettes provide an easy means of transferring files from one computer to another. Copying a file to a diskette also gives you a backup copy in case something happens to the original on your hard disk. This section describes how to use the My Computer window to copy a file from the hard disk to a diskette.
Page 74: Taking Care Of Diskettes
Learning the Basics Backing up your work Taking care of diskettes To protect the data stored on your diskettes: ❖ Store your diskettes in their boxes or other containers to protect them and keep them clean. ❖ Keep diskettes at room temperature and avoid exposing them to direct sunlight.
Page 75: Restoring Your Work
Sample Backup or Restore Wizard window Follow the on-screen instructions. Restoring your work You can also use the Backup or Restore Wizard to restore information from your backup media to your hard disk. TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk.
Page 76 Learning the Basics Using a compact disc drive If the drive is not currently installed in the Slim SelectBay, follow the instructions in on page 111. HINT: Your DVD-ROM drive is designed to play Region 1 (North America) DVD-ROMs. For more information, see properties”...
Page 77: Inserting Compact Discs
narrow object to press the manual eject button located inside the hole. CAUTION: Never use a pencil to press the eject button. Pencil lead can break off inside the computer and damage it. Inserting compact discs To insert a compact disc into the drive: Make sure the computer is turned on.
Page 78 Learning the Basics Using a compact disc drive If the disc is dusty, clean it as described in with the CD-ROM or DVD-ROM drive” on page Place the disc carefully in the disc tray, label side up. Positioning the disc in the drive Gently press the disc onto the center spindle until you feel it click into place.
Page 79: Removing Compact Discs
Playing a CD or DVD For information on playing a disc, see drive” on page Removing compact discs To remove a compact disc (CD or DVD) with the computer turned on: Press the eject button on the drive. CAUTION: Never press the eject button while the drive-in-use indicator light is glowing.
Page 80: Playing Audio
Learning the Basics Playing audio ❖ Hold a disc by its outside edge. Fingerprints on the surface can prevent the DVD-ROM drive from reading the data properly. ❖ Avoid exposing discs to direct sunlight or extreme heat or cold. ❖ To clean a disc that is dirty, wipe it with a clean, dry cloth.
Page 81: Setting Up For Communications
Rewind Play Stop Previous track Next track Mute Sample Windows Media With your pointing device, use the Windows Media screen as you would an audio control panel. Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖...
Page 82: Connecting Your Computer To A Network
Learning the Basics An overview of using the Internet ❖ An Internet Service Provider (ISP) or an online service if you plan to use the Internet Before you can use the modem, you must connect it to a standard voice-grade telephone line. See modem”...
Page 83: The Internet
❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfing the Internet ❖ Internet features ❖ Uploading and downloading files from the Internet The Internet The Internet is an association of thousands of networks and millions of computers around the world connected by communications lines.
Page 84: Connecting To The Internet
Learning the Basics An overview of using the Internet Connecting to the Internet To connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A Web browser ❖ An Internet Service Provider (ISP) account The Microsoft automatically configured on your system so that when you first start it, it guides you through signing up for a new ISP...
Page 85: Internet Features
You can also use a Search Engine, a Web site specifically designed to help you look for information. Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive email of your own, you need a mailbox on the Web, or an email address.
Page 86: Toshiba's Online Resources
File Transfer Protocol (FTP) features of your Web browser to transfer large amounts of data. Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 87: Chapter 4: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.
Page 88: Maximizing Battery Life
Mobile Computing Running the computer on battery power To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged. Please see “Maximizing battery life” in the next section for procedures. If the computer is continuously operated on AC power, either through an AC adapter or a docking station for an extended period, more than a month, the battery may fail to retain a...
Page 89: Using Additional Batteries
battery is being charged. If the DC-IN or AC power light indicator does not glow, power is not being supplied. Check the connections to the AC adapter and power cable. Charge the battery until the battery light glows green. ❖ If you have extra batteries, rotate their use.
Page 90: Charging Batteries
Do not expose the battery to fire. The battery could explode. Charging batteries The main battery and replacement batteries need to be charged before you can use them to power the computer. You can charge the main battery using either your computer or an optional battery charger. toshiba.com...
Page 91: Charging The Batteries
To charge the batteries in your computer, plug the computer into a live electrical outlet. The batteries charge whether the computer is on or off. NOTE: Use only the battery charger supplied by Toshiba for use with your computer’s batteries. The main battery light ( being charged, and glows green when it is fully charged.
Page 92: Using A Battery Charger
Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your computer and its batteries. You can order a Toshiba battery charger through the accessories information sheet or Toshiba’s Web site at toshiba.com.
Page 93: Determining Remaining Battery Power
Click Start, then click Control Panel. Click Performance and Maintenance. Click the Toshiba Power Saver icon. The Power Saver Properties window appears. The current power source and battery power remaining section displays the current charge state of the battery.
Page 94: Conserving Battery Power
Where you are working—since operating time decreases at low temperatures. Toshiba’s power-saving options greatly increase the length of time you can use the computer before having to recharge the main battery. Toshiba has combined these options into several preset power usage modes.
Page 95: Setting A Power Usage Mode
The Control Panel window appears. Click Performance and Maintenance. Click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window By changing the options that appear in the Power Saver Properties dialog box and clicking OK, you can reconfigure that function.
Page 96: Using Battery Alarms
Click Start, Control Panel. Click Performance and Maintenance. Click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. In the “Running on batteries” section, click Details. The mode Properties window appears. Click the Alarm tab and set the alarm(s), as desired.
Page 97: Turning Off The Display Automatically
Turning off the display automatically To save power, it’s a good idea to set the display to turn off automatically when you’re not using the computer. You can do this in several ways: ❖ Use the Display Properties to enable the blank screen saver.
Page 98 Mobile Computing Turning off the display automatically Sample Display Properties window with Screen Saver tab displayed In the section labeled Screen Saver, select the screen saver of your choice. In the Wait window, click the up and down buttons to set the number of minutes of inactivity before the display turns off automatically.
Page 99: Changing The Main Battery
Changing the main battery When your main battery has run out of power, you have two options: plug in the AC Adapter or install a fresh main battery. TECHNICAL NOTE: To avoid losing any data, save your files and then either completely shut down your computer, or put it into Hibernation mode before changing the main battery.
Page 100: Inserting A Charged Battery
Mobile Computing Changing the main battery Unlocking the battery Removing the discharged battery WARNING: If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Inserting a charged battery Wipe the terminals of the charged battery with a clean cloth to ensure a good connection.
Page 101: Disposing Of Used Batteries Safely
Putting spent batteries in the trash is not only irresponsible, it may be illegal. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba. The materials that came with your computer may include an insert regarding the disposal of batteries. If not, check with your local government for information on where to recycle or dispose of old batteries.
Page 102: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, diskettes, etc. See your dealer for more information.
Page 103: Chapter 5: Expansion Options
To order additional devices and accessories, see the accessories information provided with your computer, or visit toshiba.com Using your computer at the office By connecting an external full-size keyboard, an external monitor, a mouse and a printer, you can work with your computer as if it were a standard office model.
Page 104: Using An Expansion Device
For more information, see the documentation that comes with the device. To purchase an expansion device, see the accessories information packaged with your system or visit Toshiba’s Web site at toshiba.com Using the optional external USB diskette drive The optional external USB diskette drive allows you to use...
Page 105: Using The Optional Usb External Diskette Drive With A Pc Card
Using the optional external USB diskette drive Diskette-in-use light Optional external USB diskette drive and connector cable TECHNICAL NOTE: You may attach the optional external USB diskette drive while the computer is on or off. If you attempt to access the drive when it is not attached to the computer, you will receive an error message.
Page 106: Using A Keyboard With The Advanced Port Replicator
Making your external keyboard emulate the Fn key An external keyboard does not have the the computer’s built-in keyboard. You can use the Emulation option in Toshiba Hardware Setup to assign an external keyboard key combination that will emulate the internal keyboard’s In Toshiba Hardware Setup, you can emulate the setting key combinations in the keyboard option of the utility.
Page 107: Using A Mouse With The Advanced Port Replicator
Using a mouse with the Advanced Port Replicator “Toshiba Hardware Setup” on page 185 information. NOTE: The Fn emulation key is not supported when using a USB keyboard. Using a mouse with the Advanced Port Replicator If you prefer to use a mouse, you can attach one to a PS/2...
Page 108: Using A Printer With The Advanced Port Replicator
Expansion Options Using a printer with the Advanced Port Replicator docking the computer. Simply wait a few minutes until the mouse stabilizes. Using a printer with the Advanced Port Replicator In addition to connecting a printer to your computer, you can also connect a printer to an Advanced Port Replicator.
Page 109: Using External Display Devices
Connect the printer cable to the serial or parallel port on the port replicator. Connect the printer’s power cable to a power outlet and turn on the printer. Turn on the computer. CAUTION: For a parallel or serial printer, never connect the printer cable while the computer’s power is on.
Page 110: Adjusting The Quality Of The External Display
Expansion Options Using external display devices While holding down setting you want takes effect. This hot key cycles through the settings in the following order: ❖ Built-in display panel only ❖ Built-in display panel and external monitor simultaneously ❖ External monitor only Release the TECHNICAL NOTE: You can also change these settings using the Display Properties Box.
Page 111: Using Slim Selectbay Modules
HINT: Items from this list that did not come with your computer can be purchased separately. See the accessories information packaged with your system or visit Toshiba’s Web site at toshiba.com. Expansion Options...
Page 112: Removing A Module From The Slim Selectbay
Expansion Options Using Slim SelectBay modules Removing a module from the Slim SelectBay Shut down your computer completely using the Shut Down or Turn Off command. computer” on page 135. CAUTION: Installing or removing a module while the computer power is on can damage the computer, the module, or both. Turn the computer upside down and locate the Slim SelectBay module.
Page 113: Inserting A Module Into The Slim Selectbay
While holding the latch, slide the module out of the computer. Sliding the module out If you are removing the weight saver, retain it for transporting the computer when no other module is installed in the Slim SelectBay. Inserting a module into the Slim SelectBay To install a module into the Slim SelectBay, slide the module all the way into the Slim SelectBay.
Page 114: Inserting A Pc Card
Expansion Options Using PC Cards Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with your computer, but they are likely to be much more difficult to set up and use.
Page 115: Removing A Pc Card
When the card is almost all the way into the slot, push firmly, but gently, to ensure a firm connection with the computer. Avoid forcing the card into position. Removing a PC Card Locate the PC Card ejection tab that corresponds to the slot in which your PC Card is installed.
Page 116: Using An Sd Card
During installation of the SD card drivers, one or more dialog boxes may appear indicating that the driver is not digitally signed. The message may appear as “Digital Signature not found (About Secure Digital Emulation from Toshiba).” Click Yes to continue.
Page 117: Installing The Sd Card In The Sd Slot
Installing the SD card in the SD slot To insert an SD card, turn the card so that the connector (metal area) faces down then push the card in the slot until it locks in place. If the operating system does not recognize an inserted SD card, remove and insert it again.
Page 118: Removing An Sd Card
Expansion Options Using an SD card your system may not enter Standby or Hibernation mode, some tasks may become unresponsive, and the operating system may not shut down properly. If this occurs, reset your computer by holding down the power button for four seconds.
Page 119: Chapter 6: Enhancing Productivity
Chapter 6 Enhancing Productivity In this chapter, you will explore other features of your notebook computer. ® Windows XP special features The Windows several new features and enhancements, including: ❖ New system file protection ❖ A system restore function, allowing you to rollback the system to its previous mode ❖...
Page 120: Personalizing Your Desktop
Enhancing Productivity Personalizing your desktop Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work. You can customize the following aspects of the desktop: ❖ Taskbar—which resources to display for quick access ❖...
Page 121: Bringing The World To Your Desktop
Bringing the world to your desktop With the Windows desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: Point to an empty space on the desktop and click the secondary button.
Page 122: Changing Desktop And Browsing Style
Enhancing Productivity Personalizing your desktop To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. To select some other Web site, type the address of the Web site you want or click Browse to locate it. You can configure the Web content interface in several other ways.
Page 123: Personalizing Individual Windows
The My Computer window appears. Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box Click the preferred options. Click Apply, then OK. Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window.
Page 124: Customizing Window Toolbars
Enhancing Productivity Personalizing your desktop Customizing window toolbars You can display one or more customizable toolbars at the top of a window. As you browse, the operating system detects the kind of information presented in the window and automatically displays the appropriate toolbar buttons and menus.
Page 125: Displaying Information About Each Folder
The elements you can add to the top of the window are: Toolbar element Address Bar Standard buttons Displays buttons for commonly used Displaying a toolbar in a window Click Start, then click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click the name of the toolbar you want to display.
Page 126: Setting Up For Communications
Enhancing Productivity Setting up for communications Open the folder you want to view as a Web page. In the Tools menu, select Folder Options. In the Tasks section, click the button for Show common tasks in folders. Click Apply, then OK. Sample Control Panel window as a Web page The addition of the name of the folder and instructions for how to use the folder on the left give the window the...
Page 127: Determining The Com Port
❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports. The default setting for the modem is COM3.
Page 128: Using The Ethernet Lan Port
Enhancing Productivity Setting up for communications Click OK to close the Properties box, then the Phone and Modem options box. Close the Control Panel. Using the Ethernet LAN Port If your operating system is Windows can connect your computer to a Local Area Network (LAN) at work or from a remote location.
Page 129: Exchanging Data With Another Computer
Use an external CD-ROM drive. You can order a PORT-Noteworthy PC Card CD-ROM drive from Toshiba and install it in the PC Card slots on the left side of the computer. Alternatively, if you have a PC Card SCSI adapter, you can use a SCSI CD-ROM drive.
Page 130: Setting Up A Direct Cable Connection
Enhancing Productivity Exchanging data with another computer drive onto a network server and download the files onto your notebook. ❖ Use the infrared port to connect your notebook to another computer that has a CD-ROM drive. Setting up a direct cable connection To establish a direct cable connection with another computer: Click Start, All Programs.
Page 131: Using Bluetooth
It is recommended that you do not remove the modules from your computer. For assistance, contact a Toshiba Wireless Authorized Service Partner. Network Device Switch This feature lets you select actions that will enable or disable LAN and wireless LAN functions.
Page 132: Using Audio Features
The computer plays sounds through the internal speaker. It uses the sound settings in your operating system, except for the system speaker, which is configured by the Toshiba System utility. To adjust the volume, click the speaker icon in the taskbar.
Page 133: Recording Sounds
The headphone jack requires a 16-ohm stereo mini jack. To adjust the volume: ❖ For external speakers, use the volume controls on each speaker. ❖ For headphones, use the computer’s volume control dial. Recording sounds The external microphone may be used with other software to record monaural audio sounds and save them as digital audio.WAV files on disk.
Page 134: Adjusting Recording Settings
Enhancing Productivity Using audio features Positioning Sample Sound Recorder screen Click the Record button and speak normally into the microphone. NOTE: You can only record 60 seconds at a time. When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button. To save the file, select Save from the File menu.
Page 135: Powering Down The Computer
Click OK. Your new settings take effect the next time you record. Powering down the computer When you power down the computer, you have a number of options to choose from: ❖ Turn Off or Shut down, which power off the computer ❖...
Page 136: Restart Command
Enhancing Productivity Powering down the computer ❖ Restarting from Turn Off or Shut down uses the most time and battery power. ❖ When starting up again, the system does not automatically open the programs and files you were previously using. Restart command Restart is the same as Turn Off or Shut down but automatically powers up the computer.
Page 137: Standby Command
Standby command The Standby command puts the computer into a power- saving mode. Standby stores the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors to consider when choosing Standby: ❖...
Page 138: Turning Off More Quickly
Enhancing Productivity Using Turn Off or Shut down Sample Turn off computer window Click Turn Off. The computer turns itself off. If you are connected to a Windows server), power off the computer as follows: Click the Start button, then Shut down. The Shut Down window appears.
Page 139 Click Start, Control Panel. The Control Panel window appears. Click Performance and Maintenance. Double-click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window Enhancing Productivity Using Turn Off or Shut down...
Page 140 Enhancing Productivity Using Turn Off or Shut down Click Details in the Running on batteries section. The Full Power Properties window appears. Click the System Power Mode tab. Sample Full Power Properties window Select Power Off for the option you want. ❖...
Page 141: Starting Again After Turn Off Or Shut Down
Click All for the settings to apply whether you are using battery power or outlet power. Click OK to close the Full Power Properties window. Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel. Starting again after Turn Off or Shut down To start the computer up again, press and release the power button;...
Page 142 Enhancing Productivity Using Hibernation The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window In the Running on batteries area, click the Details button. Click the System Power Mode tab. Select Hibernation for the options you want.
Page 143: Going Into Hibernation Mode
Click OK to close the Full Power Properties window. Click the Hibernate tab, then click the Enable hibernate support check box. Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel. Going into Hibernation mode...
Page 144: Going Into Hibernation Mode More Quickly
Enhancing Productivity Using Hibernation The Turn off computer window appears. Sample Turn off computer window with shift key held down to show Hibernate option Hold down the shift key and click Hibernate (“Hibernate” only appears when the shift key is pressed). The computer saves the state of the system, including all open programs and files, to the hard disk, and then powers down completely.
Page 145: Starting Again From Hibernation
❖ By closing the display panel Starting again from Hibernation To start up the computer from Hibernation mode, press and release the power button until the on/off icon glows green. The computer returns to the screen you were using. If you went into Hibernation mode by closing the display panel, you can start the computer again by opening the display panel.
Page 146: Going Into Standby Mode More Quickly
Enhancing Productivity Using Standby Click Stand By. The computer saves the state of all open programs and files to memory, turns off the display, and goes into a low-power mode. The on/off light ( machine is in Standby mode. If you are connected to a Windows server), power down the computer using the Standby command as follows: Click the Start button, then select Shut down.
Page 147 The Control Panel window appears Click Performance and Maintenance. Double-click the Toshiba Power Saver icon. The TOSHIBA Power Saver Properties window appears. Sample TOSHIBA Power Saver Properties window Click Details in the Running on batteries section. The Full Power Properties window appears.
Page 148 Enhancing Productivity Using Standby Sample Full Power Properties window Select Standby for the options you want. ❖ When I press the power button Set this option to Standby so that the computer will go into Standby mode when you press the power button.
Page 149: Starting Again From Standby
Click All for the settings to apply whether you are using battery power or outlet power. Click OK to close the Full Power Properties window. Click OK to close the TOSHIBA Power Saver Properties window, then close the Control Panel. Starting again from Standby...
Page 150: Chapter 7: Windvd
Chapter 7 WinDVD Playing DVDs TECHNICAL NOTE: For optimum DVD performance, always play DVDs while your computer is connected to AC power. If your computer has a DVD-ROM drive, you can use InterVideo WinDVD to-use, full-featured multimedia control center that helps you get the most out of the exciting world of DVD technology.
Page 151: Using The Windvd Toolbar
automatically begins to play (see on page 159 To open WinDVD manually: Click Start, and point to Programs. Point to InterVideo WinDVD, then click InterVideo WinDVD. Sample WinDVD video window with the control panel Using the WinDVD toolbar The WinDVD window contains a toolbar at the top and a status bar at the bottom.
Page 152: Using The Windvd Status Bar
WinDVD Playing DVDs also contains an adjustment button (see balance” on page 171 Using the WinDVD status bar The time slider enables you to rapidly move forward or backward in the DVD content. Move the time slider to the left to move backward or move it to the right to move forward.
Page 153: Using The Control Panel Playback Buttons
WinDVD Playing DVDs Audio volume controls Time slider Counter Exit Expanded controls button Eject Playlist Repeat Maximize Properties Directional buttons Help button Sample WinDVD control panel You can open a shortcut menu, by positioning the cursor over the WinDVD window (other than over the control panel) then clicking the secondary button.
Page 154 WinDVD Playing DVDs Audio volume controls Repeat Sample WinDVD control panel Click this Time slider Eject Pause Fast reverse Previous Next To do this Repeat — plays the current chapter again, if the DVD contains chapters. Otherwise this button plays the DVD again from the beginning.
Page 155 Click this To do this Step — move forward through the DVD one frame at a time. Each time you click this button the DVD moves forward one frame. Stop — cease playing a DVD. After stopping the DVD, click the play button to resume playing the DVD.
Page 156: Maximizing The Video Window
WinDVD Using playlists Click this Maximizing the video window To close the WinDVD control panel and expand the video window to fill the screen, click the Maximize button. To display the control panel again, double-click anywhere in the video window. Using playlists TECHNICAL NOTE: The DVD author determines what features the DVD supports.
Page 157 Sample Playlist window Click the File button in the lower-right corner of the window, to indicate that you are creating a playlist of individual files. In the Directory list, select the file you want to play first, and click Add to put it at the top of the playlist. DVD files have an .mpg, .vob or .ac3 file name extension.
Page 158: Loading And Playing Playlists
WinDVD Customizing WinDVD Click OK to close the confirmation dialog box, then click OK to close the Playlist window. Loading and playing Playlists In the Playlist window, click File to display the saved playlist of files. Click Load Playlist to load the saved playlist. Once the playlist is loaded, a confirmation dialog box appears.
Page 159: Setting General Properties
Sample Properties dialog box with the General tab on top Setting general properties You use the General tab to select the region code, the drive letter assigned to the DVD-ROM drive, the autoplay default option, and which WinDVD toolbars are displayed by default.
Page 160: Setting Audio Properties
WinDVD Customizing WinDVD To change the region code, select the desired option in the Current regions list. The Remaining times until permanent box displays the remaining number of times you can change the region code again before the setting becomes permanent. In the Player settings Default DVD drive box, select the letter assigned to you DVD-ROM drive.
Page 161 In the Properties dialog box, click the Audio tab. The Audio tab moves to the front. The Current audio track box displays the format and attributes for the current audio track. Sample Properties dialog box with Audio tab on top In the Audio channels box, select the appropriate speaker mode to match your setup as follows: ❖...
Page 162: Setting Display Properties
WinDVD Customizing WinDVD channels to these speakers, for enhanced surround sound. ❖ If you have an S/PDIF compliant sound card, select Enable S/PDIF output. This option sends the stereo output through the sound card to an external receiver. In the Vocal options box, select the desired option for DVDs that support vocal as follows: ❖...
Page 163: Customizing The Control Panel
Sample Properties dialog box with Display tab selected Select the Lock aspect ratio check box to maintain the original aspect ratio when the video window is resized. Otherwise clear the check box. Select the Startup in full screen mode check box to automatically start WinDVD each time with the video window maximized and the control panel hidden.
Page 164 WinDVD Customizing WinDVD Sample WinDVD 2000 control panel options You can select a new control panel background color, or select WinDVD to display the control panel in a different format. Sample new WinDVD 2000 control panel appearance...
Page 165: Using Windvd Advanced Features
You can also select About to display copyright and version information. Using WinDVD Advanced Features TECHNICAL NOTE: The DVD author determines what features the DVD supports. Depending on the DVD format and your computer’s hardware configuration, some of the control panel features may be unavailable when playing a DVD.
Page 166 WinDVD Using WinDVD Advanced Features Use this To do this Playback speed— control the speed at which the DVD plays. Move the slider to the left to slow the play- back speed or move it to the right to play the DVD faster.
Page 167 Using WinDVD Advanced Features Use this To do this Numeric keypad — use these buttons to select a chapter by entering the chapter number. After you have entered a chapter number, click the enter button on the lower-right corner of the numeric keypad that chapter.
Page 168 WinDVD Using WinDVD Advanced Features Use this To do this Chapter button — displays a list of all the chapters in the current DVD. Select the chapter you want to play, or use the numeric keypad to enter the chapter num- ber.
Page 169 Using WinDVD Advanced Features Use this To do this Subtitles — displays a list of all the avail- able language subti- tles. This button is enabled only for DVD content that includes subtitles and supports dynamic subtitle information changes. Select the desired lan- guage, or select Default to display subtitles in the DVD’s...
Page 170: Zooming In
WinDVD Using WinDVD Advanced Features Use this Zooming in You can zoom in on an area of the WinDVD video window to get a closer look. Click the Zoom button, located in the upper-left corner of the directional button panel. Position the cursor over the top-left corner of the area you want to view in close up.
Page 171: Panning
Release the primary button. WinDVD automatically fills the window with the selected area. Panning Once you are zoomed in on an area of the WinDVD video window, you can move the zoom window location using the pan feature. With the video window in zoom mode, click the pan button, located in the lower-right corner of the directional button panel.
Page 172: Launching An Internet Browser From Windvd
WinDVD Launching an Internet browser from WinDVD The adjustment dialog box provides another set of sliders for adjusting volume and brightness. It also provides two color control sliders. Move the Color control 1 slider to the right to increase the blue and decrease the yellow color values.
Page 173: Chapter 8: Toshiba Utilities
TOSHIBA Mobile Extension Service Configuration ❖ TOSHIBA Console Fn-esse The operating system shortcuts and Toshiba’s Fn-esse program provide quick ways to open programs, documents, and folders from within any program without using the Start menu. This section describes how to use the Fn-esse program to quickly access your programs and files.
Page 174: Starting Fn-Esse
You can assign any key that is not associated with a hot key or a keyboard overlay. Starting Fn-esse You can access Fn-esse in one of two ways: ❖ Click Start, All Programs, Toshiba Utilities and Fn-esse. ❖ Click the Fn-esse icon. The Fn-esse keyboard appears.
Page 175: Assigning A Key To A Program Or Document
The program or document is now associated with the key you just selected. To open the program or document, press Windows plus the appropriate key from within any ® program. Toshiba Utilities Fn-esse ® Explorer (or the...
Page 176 Toshiba Utilities Fn-esse Using the keyboard or pointing device To assign a key to open a program or document: Start Fn-esse. Perform one of the following: ❖ Using the keyboard, press and hold the press the desired assignment key. ❖...
Page 177: Viewing Existing Key Assignments
Standby [Fn+F3] and Hibernation [Fn+F4]. To activate the utility: Click Start, then click Hotkey utility The Hotkey window appears. plus the appropriate key from within any ® program. Toshiba Utilities Hotkey utility...
Page 178: Expansion Device Properties
Put a check mark next to the desired option. Click OK. Expansion device properties To adjust the settings for the optional Slim Port Replicator, use the TOSHIBA Mobile Extension Service Configuration utility. Accessing Mobile Extension Service Configuration You can access the Mobile Extension Service Configuration utility in either of the following ways: ❖...
Page 179: Toshiba Console
Sample TOSHIBA Mobile Extension Service Configuration window TOSHIBA Console The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. You can normally access this utility in two ways: ❖ Press the TOSHIBA Console button located above the F12 key on your keyboard.
Page 180: Customize Your Computer
Toshiba Utilities TOSHIBA Console Sample TOSHIBA Console window The TOSHIBA Console offers three categories of features: ❖ Customize Your Computer ❖ Network ❖ Security Customize Your Computer The features available in this category are: ❖ Power Management ❖ TOSHIBA Button Controls ❖...
Page 181: Security
TOSHIBA Button Controls The TOHSIBA Button Controls allow you to enable or disable the TOSHIBA Console and Internet buttons and the programs associated with them. Those buttons are located just above the function keys at the top of the keyboard.
Page 182: Power Management
Toshiba Utilities TOSHIBA Console Sample TOSHIBA Controls Properties window Click the Buttons tab Check the boxes for the TOSHIBA Console button and/ or the Internet button. Under Select a Program, make the desired selections. Click Apply, then click OK. Power Management The Power Management feature enables you to control your computer’s power usage, regardless of the source, and use the...
Page 183 You can either use one of the preset modes or create and use your own customized mode. The preset modes cannot be deleted. By changing the options that appear in the Toshiba Power Saver Properties window and clicking OK, you can reconfigure that function. Any options that you change become effective when you click either OK or Apply.
Page 184 Toshiba Utilities TOSHIBA Console The windows and settings for creating and customizing AC power modes are described below. Running on batteries section This section lists the preset modes along with the estimated battery life for each mode. The preset modes are: ❖...
Page 185: Toshiba Hardware Setup
The Name field displays the name assigned to the mode in the Power Saver Properties window. You can change the name here if you wish. Toshiba Hardware Setup Toshiba Hardware Setup is the Toshiba configuration management tool. To access it: In the TOSHIBA Console, double-click the Toshiba Hardware Setup icon.
Page 186 Toshiba Utilities TOSHIBA Console Sample TOSHIBA HWSetup window The TOSHIBA HWSetup window appears with tabs for the following: ❖ Boot Priority — Allows you to change the sequence in which your computer accesses its disk drives for the files that load and initialize the operating system.
Page 187 “CPU Frequency Mode” to one of “Dynamically Switchable,” “Always High,” or “Always Low.” ❖ General — Allows you to view the current BIOS. ❖ Password — Allows you to set user passwords. ❖ Device Config—Shows the Device configuration options. Toshiba Utilities TOSHIBA Console...
Page 188: Chapter 9: Keeping Your Files Safe
When you set a password, you must enter the password before you can work on your computer again. Toshiba supports the following types of passwords on your computer: ❖ A power-on password—Prevents unauthorized users from starting or restarting the computer.
Page 189: User-Level Passwords
If you ever forget your password, contact your network administrator. Setting a user-level password To set (register) a user-level password: Click Start, Control Panel, and click Toshiba HWSetup. Open the Password tab. Click Registered. A Password dialog box appears.
Page 190: Disabling The User-Level Password
Keeping Your Files Safe Using passwords in the Windows® operating system Disabling the user-level password To delete a user-level password: Click Start, Control Panel, and click Toshiba HWSetup. Open the Password tab. Click Not Registered. A Password dialog box appears.
Page 191: Hard Disk Drive Passwords
If you have registered a user-level password, press your password and press correctly, the computer returns to where it was when you pressed the hot key. Hard disk drive passwords Your computer comes with a program preinstalled that lets you set two types of hard disk drive passwords, user and master.
Page 192: Setting A Hard Disk Drive Master Password
To set a hard disk drive master password: Click Start, then click Run. In the Run box, type: c:\Program Files\toshiba\Windows Utilities\HDDPWM\HDDPWM press Enter The Hard Disk Drive Password program HDDPWM displays a warning screen. To set a hard disk drive master password, read the warning and click To quit without setting a password, click Cancel.
Page 193 Setting a hard disk drive master password Type a password of up to 10 characters under New Password, and type it again to confirm. Click OK. CAUTION: Make sure you choose a hard disk drive master password you can remember easily. If you set a hard disk drive user password and later forget the password or lose your password diskette, you will need to enter the hard disk drive master password in order to access your hard disk.
Page 194: Setting A Hard Disk Drive User Password
Setting a hard disk drive user password To set a hard disk drive user password: Click Start, then click Run. In the Run box, type: c:\Program Files\toshiba\Windows Utilities\HDDPW\HDDPW press Enter The Hard Disk Drive Password program HDDPW displays a warning screen.
Page 195: Deleting The Hard Disk Drive User Password
A confirmation screen appears to verify you want to register the password. Click Yes. If you want to store the password on a removable media click Yes; otherwise click No to continue without storing the password on a removable media. If you are storing the password on a removable media, insert the media of you choice and type the drive and file name you want to save it as, or click Browse to search for...
Page 196 Keeping Your Files Safe Setting a hard disk drive master password In the Run box, type: c:\Program Files\toshiba\Windows Utilities\HDDPW\HDDPW press Enter The Hard Disk Drive Password program, HDDPW, displays a warning screen. To delete the hard disk drive user password, click Delete.
Page 197: Chapter 10: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter. Problems that are easy to fix Your program stops responding.
Page 198 If Something Goes Wrong Problems that are easy to fix To close a program that has stopped responding: Press Ctrl Click Windows Task Manager. The Windows Task Manager window appears. Click the Applications tab. If a program has stopped responding, the words “not responding”...
Page 199: Problems When You Turn On The Computer
Your program performs an illegal operation. If you receive the message, “ you should record the details of the message and operation ” consult the software manufacturer. To record the details: Click the Details button and select the text the operating system displays.
Page 200 If Something Goes Wrong Problems when you turn on the computer The computer starts but, when you press a key, nothing happens. You are probably in Standby mode and have a software or resource conflict. When this happens, turning the power on returns you to the problem instead of restarting the system.
Page 201: The Windows ® Operating System Is Not Working
The Windows® operating system is not working The Windows working Once you are familiar with the desktop and used to the way the operating system responds to your work routine, you can easily detect if the operating system is not working correctly. For example: ❖...
Page 202: Internet Problems
If Something Goes Wrong The Windows® operating system is not working ❖ Safe Mode (with Networking) ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configuration (your most recent settings that worked) ❖...
Page 203: The Windows Xp Operating System Can Help You
other mistake makes it impossible for your browser to locate the site. My browser can’t find a site I bookmarked. The World Wide Web is constantly changing. A site you bookmarked yesterday may not be available today or its server may be down for temporary repair. Try again later. The Windows XP operating system can help you ®...
Page 204: A Plan Of Action
If Something Goes Wrong Resolving a hardware conflict Click the Fixing a hardware problem. Choose from specific topics and follow the steps. If there is still a problem, the operating system should display a message that explains what the conflict is. A plan of action The smooth operation of the system depends on the interaction of all devices, programs, and features.
Page 205 Direct Memory Access Similarly, the data required by the device is stored in a specific place or address in memory called the Direct Memory Access (DMA). The DMA provides a dedicated channel for adapter cards to bypass the microprocessor and access memory directly.
Page 206: Fixing A Problem With Device Manager
If Something Goes Wrong Resolving a hardware conflict ❖ Reconfigure the device so that its requirements do not conflict. Refer to the device’s documentation for instructions about changing settings on the device. Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device.
Page 207: Memory Card Problems
To check a device’s properties: Click Start, Control Panel, Administrative Tools. Click the Computer Management icon. Click the Device Manager button. To view the device(s) installed, double-click the device type. To view the properties, double-click the device. The operating system displays the Device Properties dialog box, which provides an array of tabs.
Page 208: Power And The Batteries
If Something Goes Wrong Resolving a hardware conflict Remove the memory module, following the instructions “Removing a memory module” on page Reinstall the memory module, following the instructions “Installing additional memory (optional)” on page and making sure the module is seated properly. Check for the error again.
Page 209 The AC adapter and power cable work correctly, but the battery will not charge. The battery doesn’t charge while the computer is consuming full power. Try turning off the computer. The main battery may not be inserted correctly in the computer.
Page 210: Keyboard Problems
If Something Goes Wrong Resolving a hardware conflict Keyboard problems If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself. The keyboard produces unexpected characters. A keypad overlay may be on. If the numlock light or cursor control mode light is on, press turn off the cursor control mode light or simultaneously to turn off the numlock light.
Page 211: Display Problems
To remove the cap: Firmly grasp the cap and pull it straight up. Removing the AccuPoint II cap After cleaning the cap, position it on the peg and press it into place. NOTE: The peg is square, so be careful to align the cap’s hole with the peg.
Page 212 If Something Goes Wrong Resolving a hardware conflict If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to the computer is firmly attached.
Page 213: Disk Drive Problems
To change the display properties: Point at the desktop and click with the secondary button. The Display Properties window appears. Click Properties, then click the Settings tab. Adjust the screen resolution and/or color quality. Click OK. The display mode is set to Simultaneous and the external display device does not work.
Page 214 If Something Goes Wrong Resolving a hardware conflict Click the Tools tab. Click the Check now button. The Check Disk All Apps box appears. You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start.
Page 215: Problems With The Cd-Rom Or Dvd-Rom Drive
You may be inserting the diskette incorrectly. Hold the diskette with the hub side facing down, and insert it so that the metal head window cover goes into the drive first. The metal cover or a loose label may be obstructing the path into the drive.
Page 216: Sound System Problems
If Something Goes Wrong Resolving a hardware conflict You press the CD-ROM or DVD-ROM eject button, but the CD-ROM or DVD-ROM tray doesn’t slide out. Make sure the computer is connected to a power source and turned on. The CD-ROM or DVD-ROM drive eject mechanism requires power to operate.
Page 217: Pc Card Problems
If you are using external headphones or speakers, check that they are securely connected to your computer. The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers. It occurs in any sound system when input from a microphone is fed to the speakers and the speaker volume is too loud.
Page 218 If Something Goes Wrong Resolving a hardware conflict Some card manufacturers use special software called enablers to support their cards. Enablers result in nonstandard configurations that can cause problems when installing the PC Card. If your system does not have built-in drivers for your PC Card and the card did not come with an operating system driver, it may not work under the operating system.
Page 219 Double-click the appropriate PC Card. The operating system displays your PC Card’s Properties dialog box, which contains information about your PC Card configuration and status. The computer stops working (hangs) when you insert a PC Card. The problem may be caused by an I/O (input/output) conflict between the PCMCIA socket and another device in the system.
Page 220: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Refer to the card’s documentation, which should contain a troubleshooting section. Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line).
Page 221: Modem Problems
Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack. Check the port settings to make sure the hardware and software are referring to the same COM port.
Page 222: Dvd Operating Problems
If Something Goes Wrong DVD operating problems popularity of the site. If accessing a particular site is very slow, try later. My browser can’t find the URL address I typed in. Make sure you separated the domain names of the address with the forward slash(/).
Page 223 “Checking device properties” on page 206 instructions on using Device Manager to view the DVD- ROM properties. Check the Toshiba Web site for new information on DVD-ROM drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 224 Click the down arrow at the right of the current screen saver name. A list of screen savers displays. Click and hold the up arrow by the list or move the slide to the top. Click None. Click OK. “Toshiba Hardware Setup” on page 185.
Page 225: Windvd Problems
WinDVD problems WinDVD has been configured to provide optimum performance and quality based upon your system’s available resources. Changes made to the system or its configuration may impact the playback performance of the WinDVD player. General issues WinDVD controls are disabled. Controls may be grayed out by commands on the DVD.
Page 226 If Something Goes Wrong WinDVD problems WinDVD performance decreases after making a system change. DVD playback performance is dependent upon several system resources. Some software changes may also impact playback performance (for example, downloading new drivers from the Web). Before installing a new hardware or software component on your system, check for any potential conflicts between its resource requirements and your current system configuration.
Page 227: Content Issues
Content issues Movies exhibit poor performance of “Director's Commentary” or other similar optional content versions. Some movies may exhibit poor performance of these features. In particular, the video portion of the movie may become jerky or show pauses. The normal version of the movie will not show this problem.
Page 228: If You Need Further Assistance
If Something Goes Wrong If you need further assistance On a regular basis, back up the information stored on your hard disk. Here are some ways you can do this: ❖ Copy files to diskette. ❖ Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape.
Page 229: Before You Call
If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. Start with accessing Toshiba on the Internet using any Internet browser by typing: pcsupport.toshiba.com Next, try one of Toshiba’s online services. The Toshiba...
Page 230: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred. ❖ Exact error messages and when they occurred. For technical support, call the Toshiba InTouch Center: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 231: Toshiba's Worldwide Offices
Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Lim- ited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia Belgium Toshiba Information Systems Benelux (Belgium) B.V. Excelsiorlaan 40 B-1930 Zaventem Belgium Czech Republic CHG Toshiba, s.r.o. Hnevkovskeho 65 61700 Brno Finland Scribona TPC OY Sinimäentie 14...
Page 232 Toshiba Corporation, PCO- 1-1, Shibaura 1-Chome Minato-Ku, Tokyo, 105-8001 Japan Mexico and all of Latin America Toshiba de México S.A. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. 800-457-7777 (outside of the 949-859-4276 (within the US...
Page 233 Kalbakken 0901 OSLO 9 Norway Poland TECHMEX S.A. ul. Partyzantów 71, 43-316 Bielsko-Biala 01-059 Warszawa Poland Singapore Toshiba Singapore Pte. Ltd. 438B Alexandra Rd. # 06-01 Alexandra Technopark Singapore 119968 Slovenia Inea d.o.o. Ljubljanska 80 61230 Domzale Slovenia Sweden Scribona PC AB Sundbybergsväegen 1...
Page 234 Toshiba Information Systems (U.K) Ltd. Toshiba Court Weybridge Business Park Addlestone Road Weybridge KT15 2UL United Kingdom The Rest of Europe Toshiba Europe (I.E.) GmbH Hammfelddamm 8 D-4-1460 Neuss Germany United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard...
Page 235: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. Volume Mute This hot key enables/disables volume mute on your computer.
Page 236: With A Password
This hot key displays the power usage pop-up window and cycles through the battery save modes. Sample power usage modes The properties of each mode are set in the Toshiba Power Management utility. For more information, “Power Management” on page 182.
Page 237: Standby Mode
Standby mode This hot key puts the computer into Standby mode. Sample Standby confirmation box Standby mode ❖ A message box is displayed by default to confirm that the computer is going into Standby mode. You can choose not to display this message box. ❖...
Page 238: Hibernation Mode
Hot Keys Hibernation mode Hibernation mode This hot key puts the computer into Hibernation mode. Sample Hibernation confirmation box ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. You can choose not to display this message box.
Page 239: Display Modes
Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window Display brightness This hot key decreases the screen brightness. This hot key increases the screen brightness. Display modes ❖ Built-in display panel only ❖...
Page 240: Wireless Device Enable/Disable
Hot Keys Wireless device enable/disable Wireless device enable/disable This hot key enables and disables the optional wireless devices installed in your computer. The wireless modes are: Keyboard hot keys This hot key turns the cursor control overlay on and off. This hot key turns the numeric overlay on and off.
Page 241: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors Your computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved United Kingdom...
Page 242: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 243 direct memory access DIMM dual inline memory module disk operating system dots per inch DSTN dual supertwist nematic digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory enhanced capabilities port EPROM erasable programmable read-only memory file allocation table Federal Communications Commission fast infrared gigabyte...
Page 244 Glossary SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 245 application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged.
Page 246 Glossary bus — An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus.
Page 247 color palette — A set of specified colors that establishes the colors that can be displayed on the screen at a particular time. compatibility — The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another.
Page 248 Glossary direct memory access (DMA) — A dedicated channel, bypassing the CPU, that enables direct data transfer between memory and a device. directory — See folder. disable — To turn a computer option off. See also enable. disc — A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs.
Page 249 drag — To hold down the AccuPoint II control button or mouse button while moving the cursor to drag a selected object. In the ® Windows II control button or left mouse button, unless otherwise stated. driver — See device driver. DVD —...
Page 250 Glossary file extension — The three characters following the period (pronounced “dot”) at the end of a file name. The extension indicates the type of file. Examples are .exe for program files and .hlp for help files. See also file name. folder —...
Page 251 Hibernation — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 252 Glossary L2 (level two) cache — Memory cache installed on the motherboard to help improve processing speed. It is slower than L1 cache and faster than main memory. See also cache, CPU cache, L1 cache. LAN (local area network) — A group of computers or other devices dispersed over a relatively limited area and connected by a communications link that enables any device to interact with any other on the network.
Page 253 MIDI (Musical Instrument Digital Interface) — A standard for connecting musical instruments, synthesizers, and computers. The MIDI standard provides a way of translating music into a form computers can use, and vice versa. modem — Short for “modulator/demodulator.” A device that converts information from digital to analog and back to digital, enabling information to pass back and forth between digital computers and analog telephone lines.
Page 254 Glossary palette — See color palette. parallel — Processes that occur simultaneously. In communications, it means the transmission of more than one bit of information at a time. On your computer, the parallel port provides a parallel communications interface between the computer and an appropriate device.
Page 255 RAM (random access memory) — Volatile memory that can be written to as well as read. By volatile, we mean that information in RAM is lost when you turn off your computer. This type of memory is used for your computer’s main memory. See also memory.
Page 256 Glossary serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel.
Page 257 Web — See World Wide Web. Wi-Fi — A trademarked term by the Wireless Capability Ethernet Alliance which stands for Wireless Fidelity. Wi-Fi is another term for the IEEE 2.11b communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) —...
Page 258: Index
Index AC adapter DC-IN 30 plugging in 30 AC power light 35 accessories carrying case 102 devices 111 expansion devices 104 memory 44 PORT-Noteworthy computer lock cable 63 AccuPoint II MouseWare utility 57 pointing device 32 replacing the cap 210 troubleshooting 210 adding memory 44...
Page 259 99, 100 Battery lock 29 Bluetooth 131 module 130 buttons control 58 primary control 58 programmable 57 secondary control 58 TOSHIBA Console 33 CD-ROM drive opening 77 troubleshooting 215 using 75 channels DMA 205 IRQ 204 checking device properties 206...
Page 260 Index checking properties 206, 207 disabling a device 206 digital audio .WAV files 133 Digital Subscriber Lines (DSL) 83 disc, positioning 78 Disk Defragmenter 65, 214 disk drive corrupted/damaged data files 214 missing files/trouble accessing a disk 213 running slow 214 diskette care 74 copying documents to 73...
Page 261 FAT (File Allocation Table) 213 files .WAV 133 backing up 65 printing 72 restoring 75 saving 64, 71 transferring application files 129 Fn key assigning functions 174, 175 Fn-esse 174 key emulation 106 Fn-esse 173 assigning keys 174, 175 change/remove key assignments drag-and-drop 175 keyboard 174 starting 174...
Page 262 Index overview 82 slow connection 202 URL address not found 202 Internet Service Provider (ISP) 83, 86 IRQ (Interrupt Request) 204 jack headphone 31 microphone 31 keyboard 84-key 32 caps lock key 66 character keys 66 connecting to Advanced Port Replicator connecting USB-compatible 50 curser control overlay 70 emulating...
Page 263 not working 212 monitor port 28 mouse connecting to Advanced Port Replicator connecting USB-compatible 50 MouseWare utility 57 moving the computer 63 network accessing 82, 128 Dial-Up Networking Wizard 82 Network Device Switch 131 network port 28 numeric overlay 37 numlock light 37 on/off light 35 optional additional equipment...
Page 264 Index problem solving 208 power button 32, 56 power cable connectors 241 Power Management 182 running on batteries 184 power mode Super Long Life 184 power off guidelines 61 power usage modes changing 95 customizing 185 preset 94 powering down the computer 135 options 135 precautions 54 primary control button 58...
Page 265 Windows XP not working 201 programmable buttons 57 programs not running correctly 214 starting 70 Web browsers 83 real-time clock (RTC) battery 88 recording adjusting quality 134 recording sounds 133 Recovery CDs 25 transferring application files 130 region code 159 registering computer 59 remaining battery power 93 removing...
Page 266 125 Toshiba Accessories Information 25 Internet Web sites 230 registering computer 59 worldwide offices 231 TOSHIBA Button Controls 181 TOSHIBA Console 179 TOSHIBA Console button 33 Toshiba Hardware Setup 185 TOSHIBA Mobile Extension 178 Toshiba online services...
Page 267 Wi-Fi module 130 Windows Media Player 80, 81 Windows XP Help and Support 203 problem solving 201 special features 119 WinDVD 150 advanced features 165 color balance 171 control panel 152 customizing 158 help 172 Internet browser, launching 172 minimum system requirements pan 171 playing DVDs 150 playlists 156...

This manual is also suitable for:

Portege 4010 series

Toshiba 4010 User Manual

Chapter 1: Finding Your Way Around

Chapter 2: Getting Started

Chapter 3: Learning the Basics

Chapter 4: Mobile Computing

Chapter 5: Expansion Options

Chapter 6: Enhancing Productivity

Chapter 7: Windvd

Chapter 8: Toshiba Utilities

Chapter 9: Keeping Your Files Safe

Chapter 10: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Quick Links

Need help?

Questions and answers

Related Manuals for Toshiba 4010

Summary of Contents for Toshiba 4010