Batteries are collected at points of sale. Return is free of charge. If the equipment has been used for BUSINESS PURPOSES, please contact your SHARP dealer who will inform you about take-back. You might be charged for the costs arising from take-back. Small equipment (and small quantities) might be taken back by your local collection facility.
IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the CAUTION presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of RISK OF ELECTRIC sufficient magnitude to constitute a risk of electric...
DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product. SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled.
SAFETY PRECAUTIONS (Continued) 19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below: •...
- Never rub or tap the monitor with hard objects. - Do not remove or insert the power plug with wet hands. - Please understand that SHARP CORPORATION bears no Doing so could result in electric shock. responsibility for errors made during use by the customer or - Unplug the power cord if it is not used for a long time.
• Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
Troubleshooting .............58 Computer preparations ..........19 Specifications ...............60 Calibration ..............19 Mounting Precautions Touch Pen (sold separately) ........19 (For SHARP dealers and service engineers) ....65 For information on Touch Panel Settings Tool, Pen Software and Touch Display Link, see the manual for each.
Tray: 1 * SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission. * For environmental protection! Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
26. HDMI 3 input terminal (See page 12.) to connect a fixed computer and using the terminal on the 27. Audio 2 input terminal (See page 13.) side of the monitor to connect a mobile computer. Caution • Consult your SHARP dealer for attachment/detachment of optional parts.
Part Names nRemote control unit 1. Signal transmitter 2. POWER button (See page 17.) 3. MUTE button (See page 25.) 4. VOL +/- buttons (See page 25.) BRIGHT +/- buttons (See page 25.) Cursor control ( ) buttons 5. DISPLAY button (See page 25.) 6.
Connecting Peripheral Equipment 11 12 14 It is convenient to use the terminals for separate purposes; Caution For example, using the terminal on the bottom of the monitor • Be sure to turn off the main power switch and disconnect to connect a fixed computer and using the terminal on the side the plug from the power outlet before connecting/ of the monitor to connect a mobile computer.
Connecting Peripheral Equipment 7. Audio 1 input terminal 15. External speaker terminals 8. Audio 2 input terminal • To use external speakers, set SPEAKER SELECT to EXTERNAL in AUDIO OPTION on the SETUP menu. • Use an audio cable without resistance. •...
Power cord (Supplied) AC input terminal Binding Cables The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp. PN-70TB3 only Cable clamp Cable (insertion type) Cable clamp attachment Cable clamp...
Preparing the Remote Control Unit Installing the batteries Remote control operation range 1. Press the cover gently and slide it in the direction of the The operation range of the remote control unit is approx. 16.4 arrow. feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor.
Removing the Handles The handles can be removed. Handle Handle screws Caution • The removable handles and handle screws are for use with this monitor. Do not use them for any other devices. • To attach handles, be sure to use the handles and handle screws which were removed from this monitor. •...
Turning Power On/Off Turning power on/off Caution • Turn on the monitor first before turning on the computer or Press the POWER button to turn the power ON/OFF. playback device. Turning on the main power POWER button / Power LED Main power switch Status Status of the monitor...
• screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local SHARP servicing dealer or service center for assistance with battery replacement. Estimated service life of the internal battery: About 5 •...
Touch Panel / Touch Pen Preparations Touch Pen nConnecting the touch pen adapter To use the active pen, insert the touch pen adapter into the Pen tip touch pen adapter port on the monitor. TIPS • If the pen tip becomes worn or damaged, replace it. Touch pen adapter port Touch pen adapter screw Computer preparations (antitheft) Touch pen To use the touch panel, install the software below. adaptor • Touch Panel Settings Tool • Pen Software To install the software, see the manual for each. nActive Pen Preparations Inserting the battery Calibration...
Touch Panel / Touch Pen Preparations nAdding active pens (pairing) nActive pen actions Perform active pen pairing for one pen at a time. Function button 1 Function button 3 1. Click the touch pen utility icon ( ) on the taskbar. 2.
Touch action Touch action Double-tap Same action as double-clicking a mouse. Touch actions that can be used with this monitor differ Quickly touch twice with your finger/touch pen. according to operating system and application. The functions of touch actions are also different. For details, check Windows Help and the application’s support documentation.
Touch action nFinger actions Drag-and-drop Same action as drag-and-drop with a mouse. Zoom Touch the screen with your finger/touch pen and move without Use in a screen that is capable of enlargement/reduction. lifting. When you have finished the movement, lift your finger/ Touch the screen with two fingers and move your fingers touch pen.
Touch action Cautionary points Rotate Use this action in a screen that is capable of image rotation. • Do not use the touch pen for any purpose other than touch Touch the center point of the rotation with one finger. While panel operation.
Basic Operation Using the touch menu (2) Volume adjustment Changes the volume. You can touch the monitor to change input mode, volume, and other settings. Increases the volume. 1. Press the TOUCH MENU button. Decreases the volume. Mutes the sound. Touch again to return the sound to the original TOUCH MENU button volume.
Basic Operation Using the remote control unit 5. BRIGHT +/- (Backlight adjustment) Pressing displays the BRIGHT menu when the menu screen is not displayed. B R I G H T Press to adjust the brightness. * If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.
Basic Operation nSwitching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal. WIDE PC input Displays image so it fills the entire screen. AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen.
Menu Items Displaying the menu screen TIPS • The menu will differ depending on the input mode. Video and audio adjustment and settings of various functions • The menu screen will close automatically if no operation is are enabled. This section describes how to use the menu performed for about 15 seconds.
Menu Items Menu item details The menu will differ depending on the input mode. nSCREEN DISPLAY You can move the menu screen display position each time is pressed. AUTO (D-SUB1[RGB]/D-SUB2) The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. ENTER Pressing performs adjustment.
Menu Items nPICTURE DISPLAY You can move the menu screen display position each time is pressed. BRIGHT Adjusts the backlight brightness. (In PIP mode, the main side setting is reflected in the image.) CONTRAST Adjusts the difference between the bright and dark portions of the image. BLACK LEVEL Adjusts the entire brightness of the video signals.
Menu Items ADVANCED AUTO (D-SUB1[RGB]/D-SUB2) The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. ENTER Pressing performs adjustment. ANALOG GAIN (D-SUB1[RGB]/D-SUB2) Adjusts the bright portions of the video input signal. ANALOG OFFSET (D-SUB1[RGB]/D-SUB2) Adjusts the dark portions of the video input signal. 3D-NR (AV input) Reduce the noise of playback images on video.
Menu Items nAUDIO TREBLE Adjusts the volume of treble-level sound. BASS Adjusts the volume of bass-level sound. BALANCE Adjusts the balance of the audio sound between right and left. RESET Resets the values of the AUDIO menu items to the factory preset values. ENTER Select “ON”...
Menu Items TOUCH INPUT SELECT These settings enable use of the touch panel according to input mode selection. BOTTOM USB Sets which input mode the touch panel connected to the USB 1 port is used in. Select the terminal into which the video signal of the computer connected to the USB 1 port will be input.
Menu Items nMONITOR OSD H-POSITION Adjusts the horizontal display position of menu screen. OSD V-POSITION Adjusts the vertical display position of menu screen. OPERATION MODE MODE1 ..OFF IF NO OPERATION is set to ON, and STANDBY MODE is set to LOW POWER. (These settings can not be changed.) MODE2 ..Will perform standard operation.
Menu Items nPIP/PbyP PIP MODES Sets the display method. OFF ...Displays one screen. PIP .....Displays a sub screen inside a main screen. PbyP ..Displays a main screen and a sub screen in a line. PbyP2 ..Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line. PIP SIZE Sets the size of the sub screen in PIP mode.
Menu Items nOTHERS SCREEN MOTION PATTERN Residual images are reduced by moving the screen. OFF ....SCREEN MOTION function is disabled. PATTERN1 ..The whole screen moves vertically and horizontally. PATTERN2 ..A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. PATTERN3 ..
Menu Items nDual screen display nZOOM2 SPECIAL SETTING You can display two screens simultaneously. If you connect a laptop computer with any of the following Set this function with “PIP MODES” in the PIP/PbyP menu. screen resolutions and black bands appear around the screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the A sub screen is displayed OTHERS menu to ON and then select ZOOM2 in the SIZE...
Menu Items nSCHEDULE Caution You can set the time to switch the monitor on and off. • Do not switch off the main power after setting the Set this function with “SCHEDULE” in the SETUP menu. (See SCHEDULE. page 31.) •...
Menu Items Adjustments for PC screen display nAutomatic adjustment When you use D-SUB1 or D-SUB2 to display a computer screen for the first time, or when you change the setting of the computer, use the automatic screen adjustment. 1. Switch the input to D-SUB1 or to D-SUB2 and display the adjustment pattern.
Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can return the settings to their factory-preset values and OSD DISPLAY restrict operations. Shows/hides the menu, modes and messages. The FUNCTION screen cannot be hidden. SIZE 1. Hold down until “F” appears in the upper left ON 1 ....
Controlling the Monitor with a PC (LAN) Settings to connect to a LAN Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN. You can also configure the monitor to send e-mail notification Set the monitor’s IP address and subnet mask to match the when it has a problem.
Controlling the Monitor with a PC (LAN) ■ To set from a PC 7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set When the monitor is connected to a PC, LAN settings can be as follows.
Controlling the Monitor with a PC (LAN) Controlling with a PC 4. Click on “LAN SETUP” under NETWORK. TIPS • For security, set a USER NAME and PASSWORD. ■ Basic operation You use Internet Explorer on a PC on the LAN to control the monitor.
Controlling the Monitor with a PC (LAN) ■ INFORMATION ■ ADJUSTMENT Information about this monitor appears. You can adjust these settings which are also available on the monitor’s menu. • SCREEN (See page 28.) • PICTURE (See pages 29 to 30.) •...
Controlling the Monitor with a PC (LAN) ■ NETWORK (LAN SETUP) ■ NETWORK (SECURITY) This screen allows you to set the settings necessary when the This screen allows you to specify the security-related settings. monitor is connected to a LAN. USER NAME / PASSWORD DHCP CLIENT Sets up a user name and password to restrict access to this...
Controlling the Monitor with a PC (LAN) ■ NETWORK (GENERAL) ■ MAIL (ORIGINATOR) This screen allows you to specify the general LAN settings. This screen allows you to configure the e-mail sent periodically or when the monitor has an error. The settings depend on the configuration of your LAN.
Controlling the Monitor with a PC (LAN) ■ MAIL (RECIPIENT) ■ MAIL (PERIODICAL) This screen allows you to specify the recipients of the e-mail When PERIODICAL for CONDITION of MAIL (RECIPIENT) is sent periodically or when the monitor has an error. checked, set the date and time to send the mail.
Controlling the Monitor with a PC (LAN) ■ SNMP Caution You can configure settings related to SNMP. • After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch.
Controlling the Monitor with a PC (LAN) [Advanced operation] [Advanced operation] Command-based control Communication procedure nCommand format You can control the monitor using control commands (see page 50.) via terminal software and other appropriate When a command is sent from the PC to the monitor, the applications.
Controlling the Monitor with a PC (LAN) nResponse code format nCommunication interval When a command has been executed correctly • After OK or ERR is returned, you must send the following commands. Return code To set a timeout for the command response, specify 10 , 0A seconds or longer.
Controlling the Monitor with a PC (LAN) [Advanced operation] Control command table How to read the command table Command: Command field (See page 48.) Direction: W When the “Parameter” is set in the parameter field (see page 48.), the command functions as described under “Control/Response Contents”.
Controlling the Monitor with a PC (LAN) SCREEN menu Function Command Direction Parameter Reply Control/Response contents AUTO ASNC When the input mode is D-SUB1[RGB], D-SUB2. CLOCK CLCK 0-1200 0-1200 When the input mode is D-SUB1[RGB], D-SUB2. Varies depending on the signal. PHASE PHSE 0-63...
Controlling the Monitor with a PC (LAN) Function Command Direction Parameter Reply Control/Response contents AGIN When the input mode is D-SUB1[RGB], D-SUB2. ADVANCED AUTO ANGA 0-127 0-127 When the input mode is D-SUB1[RGB], D-SUB2. ANALOG GAIN ANOF 0-127 0-127 When the input mode is D-SUB1[RGB], D-SUB2. ANALOG OFFSET 3D-NR (AV input) TDNR...
Controlling the Monitor with a PC (LAN) SETUP menu Function Command Direction Parameter Reply Control/Response contents DATE/TIME SETTING DATE AABBCCDDEE AABBCCDDEE AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute DATE DISPLAY FORMAT DTFT 0-2 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY YYYY: Year, MM: Month, DD: Day TIME DISPLAY FORMAT TMFT...
Controlling the Monitor with a PC (LAN) MONITOR menu Function Command Direction Parameter Reply Control/Response contents OSD H-POSITION OSDH 0-100 0-100 OSD V-POSITION OSDV 0-100 0-100 OPERATION MODE FNCM 0: MODE1, 1: MODE2 STANDBY MODE STBM 0: STANDARD, 1: LOW POWER When ADJUSTMENT LOCK is set to ON2, LOW POWER cannot be selected (ERR).
Controlling the Monitor with a PC (LAN) OTHERS menu Function Command Direction Parameter Reply Control/Response contents SCREEN MOTION PATTERN SCSV 0-4 0: OFF, 1-4: PATTERN1-4 MOTION TIME1 MTIM 0-20 0-20 MOTION TIME2 MINT 10-990 10-990 Per 10 seconds (PATTERN1) MOTION TIME2 MINT 5-20 5-20 Per second...
Controlling the Monitor with a PC (LAN) Initialization/Functional Restriction Setting (FUNCTION) menu Function Command Direction Parameter Reply Control/Response contents ALL RESET RSET 0: ALL RESET 1, 1: ALL RESET 2 ADJUSTMENT LOCK ALCK 0-2 0: OFF, 1:ON1, 2:ON2 When STANDBY MODE is set to LOW POWER, ON2 cannot be selected (ERR). ADJUSTMENT LOCK TARGET ALTG 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH...
Controlling the Monitor with a PC (LAN) Commands for setting of the GAMMA user data Function Command Direction Parameter Reply Control/Response contents RED GAMMA DATA TRANSFER UGRW aaxxxx ··· xxxxcc aa: Block number (xxxx: 32 pieces) xxxx: 32 pieces of user data GREEN GAMMA DATA TRANSFER UGGW aa: 01-16...
“STATUS [xxxx]” appears in the corner of the screen. • Hardware has a problem. Turn off the monitor and request The video from D-sub2 input terminal does not appear repair from your SHARP dealer. correctly. (When STATUS ALERT is set to OSD & LED. This varies •...
Internal temperature rises quickly if the vents on the monitor are blocked. - Internal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove dust if possible. Ask SHARP dealer about removing internal dust.
When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from...
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product.
14 W OFF STATE Upper value: PN-70TB3, Lower value: PN-60TB3. When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF. nDDC (plug and play) The monitor supports the VESA DDC (Display Data Channel) standard.
Specifications D-sub input terminal pins DisplayPort input terminal pins (Mini D-sub 15 pin) (DisplayPort 20 pin) Function Function Function Function MainLane 3- Red video signal input 12 MainLane 0+ Green video signal input 10 GND MainLane 3+ 13 Gnd Blue video signal input N.C.
Mounting Precautions (For SHARP dealers and service engineers) • When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people. • Be sure to use a wall-mount bracket designed or designated for mounting the monitor.