Page 1
MODIFICATION NOTICE. SERVICE MANUAL MODEL E1K E1C AVR-1712 AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
Page 2
CONTENTS SAFETY PRECAUTIONS ............3 SCHEMATIC DIAGRAMS ............86 7CH-AMP UNIT (1/2) ..............86 NOTE FOR SCHEMATIC DIAGRAM .........4 7CH-AMP UNIT (2/2) ..............87 TECHNICAL SPECIFICATIONS ..........5 SPK UNIT ................88 DIMENSION ................5 SMPS UNIT ................89 CAUTIONS IN SERVICING ............6 REG UNIT ................90 Initializing AV SURROUND RECEIVER ........6 SIDE_CNT UNIT ..............91 Service Jig ................6 FRONT_CNT UNIT ..............92...
Page 3
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
Page 4
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
Page 5
TECHNICAL SPECIFICATIONS n Audio Section n Tuner section • Power amplifier [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 –15 Rated output : Receiving Range : [FM] 87.5 MHz – 107.9 MHz [AM]520 kHz – 1710 kHz Front : 90 W + 90 W (8 Ω, 20 Hz –...
Page 6
DOCK CONTROL 9 DOCK CONTROL 8 Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from DENON Official Service Distributor in your region if necessary. EXTENSION UNIT KIT 8U-110084S 1 Set (Refer to 39 page.)
Page 7
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". •...
Page 8
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
Page 9
1. FRONT PANEL ASSY FRONT PANEL ASSY Proceeding : TOP COVER → (1) Remove the screws. View from the bottom (2) Disconnect the connector wires and FFC cable, then remove the screws. STYLE PIN : Loosen CP101 STYLE PIN : Loosen FFC cable Please refer to "EXPLODED VIEW"...
Page 10
2. PCB HDMI Proceeding : TOP COVER PCB HDMI → (1) Remove the screws. Shooting of photograph: A (2) Disconnect the connector wires and FFC cable, then remove the HOLDER. Disconnect the connector board. FFC cable HOLDER Board to board Board to board...
Page 11
3. POWER TRANS MAIN Proceeding : TOP COVER PCB HDMI POWER TRANS MAIN → → (1) Disconnect the connector wires, then remove the screws. CP101 STYLE PIN : Loosen CX102 CP102,104 4. PCB AUDIO_VIDEO ASSY Proceeding : TOP COVER PCB HDMI PCB AUDIO_VIDEO ASSY →...
Page 12
5. PCB SMPS/PCB SPK Proceeding : TOP COVER PCB HDMI PCB AUDIO_VIDEO ASSY → → PCB SMPS/PCB SPK → (1) Remove the screws and CARD SPACER. CARD SPACER View from the bottom (2) Disconnect the connector wires, then remove the screws. CP402 CP403 CP405...
Page 13
(3) Remove the PCB SMPS/PCB SPK from the CHASSIS, then cut the wire clamp band. PCB SMPS PCB SPK Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B. 6. PCB REG/PCB REG_CNT Proceeding : TOP COVER PCB HDMI PCB AUDIO_VIDEO ASSY →...
Page 14
7. RADIATOR ASSY Proceeding : TOP COVER RADIATOR ASSY → (1) Remove the screws. View from the bottom (2) Disconnect the connector wires and FFC cable. STYLE PIN : Loosen CP401 CP402 CP403 CP405 FFC cable...
Page 15
(3) Remove the screws. Shooting direction: C Shooting direction: D CP101 STYLE PIN : Loosen Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in RADIATOR ASSY.
Page 16
(Troubleshooting) Diagnostic mode CONTROL 2 The signal paths of the set can be easily confirmed after repair. When using multiple DENON AV receivers in the same room, make DOCK STATUS Remote ID Setup mode this setting so that only the desired AV receiver operates.(Refer to 21...
Page 17
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "DIMMER" buttons. Now, press the "STATUS"...
Page 18
1.3. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t . Condition Status FL Display Trouble shooting • Please check the Compared with the destination setting destination-resistors (R773/R776, HDMI on the board.
Page 19
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When the set is started up in this mode, the error information is displayed. Starting up: • Common in all the models Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "SLEEP" buttons. The error (protection history display) mode is set.
Page 20
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the set in error (protection display) mode and display the error, then press and hold down the "iPod 1 " button for 3 seconds.
Page 21
3. Remote ID Setup mode 3.1. Specifications When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates. 2.2. Setting the AV receivers Starting up: Press and hold both "STATUS" and "DOCK CONTROL 2 " buttons for over 3 second with the power turned on.
Page 23
4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 4.1. Starting diagnostic mode Press the ON/STANDBY button to turn on the power while pressing both the "DOCK CONTROL 2 " button and the "STATUS" button at the same time. s Q1, Q2 and Q3 are lit in FL display.
Page 24
Input Mode : Fixed DIGITAL qZONE2 POWER OFF ·Input : Digital / Output : Speakers (SURR BACK L/R) 1.Press [AMP] Except the AVR-1712 model. (ZONE2 : NET / USB) Amp assign : ZONE2 2.Press [ZONE SELECT] , Select "ZONE2" ·Input : Digital / Output : LINE OUT(ZONE2 L/R) AVR-2112 model only...
Page 25
BLOCK DIAGRAM fig.1 VIDEO BLOCK DIAGRAM SPI FLASH HDMI1 HDMI OUT HDMI2 (HDMI B’D) IC9 (HDMI B’D) TMDS SW ADV7623 HDMI3 ADV3002 HDMI TRANSCEIVER HDMI IN HDMI4 HDMI5 IC12 (HDMI B’D) AVR19/2112 ONLY HDMI HDMI6 TRANSMITTER TMDS OUTPUT ADV7511 36-BIT YCbCr/RGB U4 (HDMI B’D) HDMI Rx VIDEO DECODER...
Page 26
fig.2 VIDEO BLOCK DIAGRAM SPI FLASH HDMI1 HDMI OUT HDMI2 (HDMI B’D) IC9 (HDMI B’D) TMDS SW ADV7623 HDMI3 ADV3002 HDMI TRANSCEIVER HDMI IN HDMI4 HDMI5 IC12 (HDMI B’D) AVR19/2112 ONLY HDMI HDMI6 TRANSMITTER TMDS OUTPUT ADV7511 36-BIT YCbCr/RGB U4 (HDMI B’D) HDMI Rx VIDEO DECODER ADV7844...
Page 27
fig.3 VIDEO BLOCK DIAGRAM SPI FLASH HDMI1 HDMI OUT HDMI2 (HDMI B’D) IC9 (HDMI B’D) TMDS SW ADV7623 HDMI3 ADV3002 HDMI TRANSCEIVER HDMI IN HDMI4 HDMI5 IC12 (HDMI B’D) AVR19/2112 ONLY HDMI HDMI6 TRANSMITTER TMDS OUTPUT ADV7511 36-BIT YCbCr/RGB U4 (HDMI B’D) HDMI Rx VIDEO DECODER ADV7844...
Page 28
fig.4 VIDEO BLOCK DIAGRAM SPI FLASH HDMI1 HDMI OUT HDMI2 (HDMI B’D) IC9 (HDMI B’D) TMDS SW ADV7623 HDMI3 ADV3002 HDMI TRANSCEIVER HDMI IN HDMI4 uCOM HDMI5 IC12 (HDMI B’D) AVR19/2112 ONLY HDMI HDMI6 TRANSMITTER TMDS OUTPUT ADV7511 36-BIT YCbCr/RGB U4 (HDMI B’D) HDMI Rx VIDEO DECODER...
Page 39
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from DENON Official Service. Distributor in your region if necessary. NOTE: The incorrect connection with in the JIG (EXTENSION UNIT KIT) may cause damage.
Page 40
(4) Connect the six extension jig cables. PCB HDMI Connection table of Board to Board Ref. No. Ref. No. SIDE CNT 13 pin HDMI SIDE CNT 19 pin HDMI FRONT CNT 33 pin CP11 HDMI FRONT CNT 13 pin CP10 HDMI FRONT CNT 13 pin...
Page 41
WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE When the U-PRO (Microprocessor) or the Flash ROM is replaced, confirm the following. After PWB Name Ref. No. Description Remark replaced R5F56108VNFP SOFTWARE: Main HDMI IC41 EN29LV160BB-70TIP SOFTWARE: DSP ROM HDMI EPM3032A-TC44 SOFTWARE: AUDIO PLD HDMI...
Page 42
1.3. Turn on the AV receiver Operate the following. Turn on the AV receiver. (1) Connect the power cable to the AC outlet while simultaneously pushing the "SLEEP" button and the "iPod 1 " button of the front panel. (2) Confirm the power indicator is green and "WRITTING" is displayed in the front panel. 1.4.
Page 43
1.6. Download the firmware (1) Click the "Load" button. (2) Download the firmware from the specified download source to PC. XXX-XXXX XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin 1.7. Complete the firmware updating (1) Click the "Update" button. XXXXXXXX XXXXXXX (2) When writing of the firmware is completed, the power of AV receiver turns on automatically and you can see the "Update completed"...
Page 44
(3) If you can’t complete the firmware update, please retry the firmware update from "1.3. Turn on the AV receiver". 1.8. Notice: Please keep the following notice for firmware update. (a) Keep the PC environment (b) Avoid the communication cable from the electrical noise source. (e.g.
Page 45
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Temperature should be at avoid direct blow from an air conditioner or an electric fan and humidity should be moderate, and place the set at normal usage environment. 15 °C ~ 30 °C (59 °F ~ 86 °F) (2) Presetting •...
Page 50
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
Page 51
2. Analog video MONITOR OUT (CVBS/COMPONENT) output NG Input COMPONENT Input CVBS Input S Function : SAT Function : DOCK Function : SAT To A To B To C...
Page 52
Input CVBS Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D HDMI B'D flaw. FB112 : H(5V) FB114 : L(0V) FB116 : L(0V) FB124 : H(5V)
Page 53
Input Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D HDMI B'D flaw. FB124 : L(0V)) FB126 : L(0V) FB118 : L(0V) FB120 : L(0V)
Page 54
Input COMPONENT Is the power supply voltage correctly output? FRONT CONNECTOR B'D REGULATOR B'D flaw. V+5V : CP13B-4pin V-5V : CP13B-1pin Check on set value of each IC. Is they the following voltage values? HDMI B'D flaw. HDMI B'D FB100 : H(5V) FB103 : H(5V) FB122 : H(5V) Extend HDMI B'D using a jig.
Page 56
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player operating instructions. (7) When you use a DENON BD/DVD player, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-DENON BD/ DVD player, proceed to "YES".
Page 57
"HDMI" indicator lit? for the input on the side on which the BD/DVD player is connected. JACK5/JACK7) If using a non-DENON BD/ Is communication waveform confirmed in TP[SCL/SDA] around each to the IC (U1 DVD player, proceed to "NO".
Page 58
Check operation of each device. (AMP source : BD / Video input of player : 480P / Connect the TV.) Check operation of U1(ADV3002). (20) Check power supply. Are 5V or 3.3V supplied to U1 (each power supply pin)? The power supply circuitry is defective. Refer to [Detail C] of the substrate for test point.
Page 60
DDC_CLK/DDC_DATA/TMDS : Check items HDMI to HDMI (17)/(19)/(23) 0.9V DDC_CLK 2.48V TMDS Waveform DDC_DATA Timing waveform illustration from the start of CEC3.3V to when reset is released : Check items HDMI to HDMI (21)/(26) CEC3.3V 330ms RESET Controlled waveform(I2C), when power is turned on : Check items HDMI to HDMI (22) HSCL HSDA POWER ON...
Page 61
4. AUDIO 4.1. AUDIO CHECK Refer to "Audio Check PATH" (67 page). Audio output NG. INPUT CHECK1 SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH DIRECT ANALOG INPUT CHECK2 SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 62
4.2. Power AMP (MAIN UNIT) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
Page 63
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. AV B'D CP14? Is the audio signal transmitted to The power amplifier is repaired. AV B'D CN401? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to AV B'D CP14?
Page 64
5. SMPS DC 5V is not output. Replace the IC102(TOP258MG) and Is there damage in IC102 (TOP258MG)? D100/D101/D102/D104. Is there the damage in D100/D101/ Is the fuse (F100) blown? Replace the damaged parts. D102/D104/C102? Does the jumper (D301) wire connected Repair the jumper wire.
Page 65
Operation waveform for each part Primary drain (Caution: High voltage, electric shock) After primary side rectification (Caution: High voltage, electric shock) After secondary rectifications OPTION SMPS B'D OPTION E3 L101 C131 0.01/250V L100 OPTION OPEN LF4ZBE273H J151 JUMPER D100 1N4007 ZD100 D101 1N4007...
Page 68
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK WAVE FORM MSLK_OUT RXMCK DIR input SCLK_OUT RX64FS AP5_OUT RXFS ADV7623 AP1_OUT RXI2S0 HDMI Tranceiver AP2_OUT RXI2S1 AP3_OUT 12 RXI2S2 CH1:C1(RX0) AP4_OUT RXI2S3 AP0_OUT IC22 EPM3032ATC44-10N Audio PLD RXSPDIF DAC256FS MCLK DSP1OUT64FS/DAC64F BICK DSP1OUTFS/DACFS LRCK...
Page 69
LEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15218FP ANALOG H/POUT SPEAKER LINE IN GAIN ADJ. MIC IN AK5358B AK4358VQ AZ4580 MAX.OUTPUT 7.78Vrms +30dB SP OUT R2A15218 MAX.OUTPUT 3.8Vrms AK4358VQ 4.24Vrms/8Ω DIFF.OUT AK5358B 0dBFS=5Vpp =1.77Vrms FULL SCALE LEVEL=2Vrms +20dB SINGLE INPUT +20dB 0dBFS 0dBFS=3Vpp DOLBY LIMIT LEVEL (ALLch-3dBFS)
Page 74
LEVEL DIAGRAM ZONE2 R2A15218FP SURR.BACK FRONT/ZONE ASSIGN from F-ch from SPEAKER DA SB-ch LINE IN MAIN NET/USB LINEOUT ZONE2 DAC (AVR2112 ONLY) AK4424ET +30dB SP OUT AK4424ET 4.24Vrms/8Ω Single end OUT 0dBFS=5.66Vpp MAX SIGNAL LEVEL 2.00Vrms =2Vrms +20dB +20dB 0dBFS +10dB -10dBFS +10dB...
Page 91
REG_CNT 2/4 SIDE CONNECTOR OPTION_M OPTION_N RC5/M-X PORT RC5/M-X PORT MODEL AVR1712 AVR1912 AVR2112 REG_CNT 4/4 B6 REG_CNT 4/4 B3 AREA E2 E1C EA OPTION M OPTION N OPTION O CN402 CN403 C125Z2-11P C125Z2-13P DIGITAL CNT DIGITAL CNT HDMI 13/13 N4 HDMI 13/13 N3 OPTION_O EXT_IN 1/1 E5...
Page 92
REG_CNT 3/4 FRONT CONNECTOR DIGITAL_CNT DIGITAL_CNT DIGITAL_CNT DIGITAL_CNT HDMI 13/13 D7 HDMI 13/13 H7 HDMI 13/13 H3 HDMI 13/13 D4 CP10 CP11 TO HDMI CP13B VIDEO+5V VIDEO_GND REG_CNT 1/4 B3 VIDEO_GND VIDEO-5V CP114 CP112 CP113 CP115 TO AV B'D AV 2/3 O7 AV 2/3 O5 AV 1/3 J1 AV 1/3 F1...
Page 101
ADV7511 AVR1712 ONLY ALL OPEN ADV7511_TX_INT HN1K02FU ADV7511_RST HSCL HSDA DVSCL DVSDA C516 4.7UF-K C517 OPEN C518 OPEN 1TXVSYNC 1TXHSYNC 1TXDE 1TXPCK R254 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 OPEN 1TXR11 1TXR10...
Page 102
NET/PHY TO DM860 AVR1712 ONLY ALL OPEN TO AUDIO PLD 860SPDIF NET3.3V FROM D_SUPPLY DGND OPEN R262 R263 DLW21SN181SQ2L R264 OPEN 5P(20010WS) microSMD175F 0(2012) IC13 MFI341S2164 R265 R266 2 3 4 5 OPEN R272 FDC608PZ PHY_RST C552 4.7UF-K C553 OPEN R273 E_RESETN C554...
Page 103
OPEN AVR1712 ONLY ALL OPEN DM860 R311 OPEN DEBUG_RX DEBUG_TX SDRAM USBD- NET3.3V DGND DGND NET3.3V NET3.3V DGND NET1.2V SSMCMD SSMD2 TXD1 RXD0 DM_D0 DM_D1 JTAG DM_D2 USBD+ NET3.3V DGND NRES33OUT NRES12OUT RREF SSMD0 SSMD3 RXD1 NRESET DM_D3 ETDO IC16 R315 DM_D4 ETDI...
Page 104
DIR/AUDIO PLD AVR1712 OPEN TO DM860 TO HDMI RX/TX(ADV7623) TO CPU ZONE2 DEMZ2 MCLK1 DIRPERRZ2 R414 DIR_DOUT DIR_DIN SDIN SLRCK DIR(ETHER)_CE SBCK R415 DIR_CLK DATADIRZ2 RDATA R416 R417 DIR(ETHER)_RST XMODE RLRCK FSDIRZ2 IC19 C665 100N-K DGND LC89058W-E DVDD C666 100N-K DVDD DGND R418...
Page 105
PLD PART CPU PART OPEN DTCK DTDO R492 OPEN DTMS R495 OPEN TRST DTRST R505 DEMU0 EMU0 R496 EMU1 DTDI W9864G6JH-6 C967 1N-K C225 1N-K C751 100N-K DQ15 .DSPD0. VDDQ VSSQ .DSPD15. C752 100N-K R509 .DSPD1. DQ14 .DSPD14. 95 94 R510 OPEN .DSPD2.
Page 106
TO DIR/AUDIO PLD MAIN DAC R563 0(1608) R564 R565 OPEN OPEN C798 C799 R566 OPEN 10/16(MVG) OPEN R568 R567 ADINR OPEN OPEN DAGND ADINL C800 IC27:A C802 OPEN DAGND OPEN OPEN 0(1608) R570 DACRTNGND 0(1608) R571 0(1608) R572 R574 R573 OPEN DASBR OPEN...
Page 107
CPU LEVEL CHG TO DIGITAL CONNECTOR AVR2112 AVR1912 AVR1712 0-1608 OPEN OPEN *OPTION "E" USE FOR NON-RDS MODEL FROMD.SUPPLY CEC3.3V CEC5V REMOTE3.3V SWM5V SWM3.3V M3.3V DGND FROMD.SUPPLY R661 FFC-4P M3.3V 232MO 232MI SWM3.3V DGND C980 OPEN R687 R688 R689 DGND R824 SWM3.3V 19 18 17...
Page 108
DSP PARTS TO CPU LEVEL CHG ADV7511 ADV3002 APLD+DAC HDMI PARTS MODEL AVR1712 AVR1912 AVR2112 AREA E3 E2 OPTION A OPTION B OPTION C OPTION D OPTION E TO D.SUPPLY CEC_COM ADV7623_INT1 ADV7623_INT2 ADV7623_TX_INT MAIN_POWER ADV7623_SPI_MO ADV7623_SPI_MI BDOWN R845 OPEN ADV7623_SPI_CLK E_POWER R846...
Page 114
Ref. No. Part No. Part Name Remarks Q'ty New CORD ASSY L068125100020S 00D9630292205 POWER TRANS MAIN 963101100020S 8200960611030S BRACKET H SINK 4010056906010S HEAT SINK MAIN 2120211988000S Q410,Q422,Q434,Q446, TR 2SB1560-Y J5011560Y0000S ★ 34 00D9960018706 Q458,Q470,Q482 Q409,Q421,Q433,Q445, TR 2SC3964 ★ 35 00D9630280107 J502396400000S Q457,Q469,Q481 Q404,Q416,Q428,Q440,...
Page 115
PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES z Parts indicated by "nsp" on this table cannot be supplied. z Parts indicated by the " ★ " mark are not illustrated in the exploded view. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Ref.
Page 116
G670001R50230S 307010087002D REMOTE CONTROL( RC-1156) 8300115600010S PE SHEET 6327040059000S 963533013490D CUSHION SNOW L/R 6230212954000S POLY BAG ACCESSORY 6330210222000S 324010001003D MIC CONDENSER M040000310040S 963537100020D PAD BOX BACK 6240210730000S 963531013520D BOX GIFT 6007211860060S LABEL DENON CONTROL 5507000007000S ★ 18 LABEL HOT-SURFACE 5507000003730S...
Page 117
EX3AV SEMICONDUCTORS Only major semiconductors are shown. General semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. Temp Rating EX3AV Part Number (° C) Package 1. IC's EX3AV -40 to +85 38-pin QFN T&R...
Page 120
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 121
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 122
Pin No. Mnemonic Type Description PGND Ground PVDD Ground. PVDD Power PLL Supply Voltage (1.8 V). XTAL Miscellaneous Input pin for 28.63636 MHz crystal or an external 1.8 V 28.63636 MHz clock oscillator source to analog clock the ADV7623. XTAL1 Miscellaneous Crystal Output Pin.
Page 123
ADV7623 Block diagram XTAL XTAL1 VIDEO DATA RXA_C RXB_C RXC_C AUDIO DATA VIDEO DATA RXD_C RXA_0 RXA_1 EQUALIZER SAMPLER RXA_2 AUDIO DATA VIDEO DATA RXB_0 VIDEO DATA SAMPLER RXB_1 EQUALIZER RXB_2 AUDIO DATA RXC_0 EQUALIZER SAMPLER AUDIO DATA RXC_1 RXC_2 RXD_0 RXD_1 EQUALIZER...
Page 124
LC89058W-E (HDMI : IC21) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK LC89058W-E DV DD DGND DGND DV DD RBCK GPIO0 GPIO1 RMCK GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 125
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 126
ADSP21487KSWZ3B (HDMI : U8) PIN 1 GND PAD (PIN 177) at BOTTOM TOP VIEW (PINS DOWN) ADSP21487KSWZ3B Terminal Function Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE DPI_P07 FLAG1 DAI_P20 FLAG2 CLK_CFG1 DPI_P09 ADDR0 DPI_P10...
Page 128
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY...
Page 129
W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, Address A0−A10 A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 130
EN29LV160BB-70TIP (HDMI : U7) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB-70TIP Block Diagram Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter Data Latch Output Enable Logic...
Page 135
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 14 VCL Smoothing capacitor connection pin 15 MD1 M3VPu 16 MD0 M3VPu (MUTE POWER) Reserve (PRE MUTE control) 17 P86 REMOTE POWER(232C) 18 P85 232C POWER control pin(ON: H) 19 RES# RESET Reset input (reset: L) 20 XTAL...
Page 136
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 57 VSS 58 P82/TRCLK FL CE FL control order pin 59 VCC +3.3V 60 P81/TRSYNC FL RST FL control order pin S VSEL B S VIDEO switcher control pin (TC4052) 61 P80 MINI JACK connection detection pin for DOCK 62 BCLK/P53...
Page 137
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY ISEL B(AVR1912E2,AVR2112)/ Input Selector rotation detection pin(Rotary encoder) 106 PE3/D11 SW3Pu/- NC(AVR1912E3,AVR1712) / NC (AVR1712/AVR1912E3) VOL CLK FUNCTION/VOLUME control pin(R2A15218) 107 PE2/D10 VOL DATA FUNCTION/VOLUME control (R2A15218) 108 PE1/D9 PLD WRITE A.PLD /JTAG switching control pin 109 PE0/D8 JTAG TDO...
Page 138
MC14094B MC14094BDTR2G (HDMI : IC35) PIN ASSIGNMENT STROBE OUTPUT DATA ENABLE CLOCK Q′ TRUTH TABLE Parallel Outputs Serial Outputs Output Enable Q′ Clock Strobe Data No Chg. No Chg. No Chg. No Chg. No Chg. −1 No Chg. −1 No Chg. No Chg. No Chg.
Page 139
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control R2A15218FP (AV : IC801) BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB -∞...
Page 140
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out, 3, 99...
Page 144
PARTS LIST OF P.C.B. UNIT z Parts indicated by "nsp" on this table cannot be supplied. z The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. PCB 7CH_AMP ASS'Y Ref.
Page 145
Ref. No. Part No. Part Name Remarks Q'ty ZD420,421 00D9630047502 D,ZENER MTZJ3.3B K06003R344520S RESISTORS GROUP R404 R,FIXED 1WJ-5.6K N113135656220S R406 963252004160S POSISTOR 18BC471QB5RB F320184710050S R408 R,FIXED 1WJ-5.6K N113135656220S R415 963125012630S R,METAL FILM 22-J,1W FLAME RETARDANT C060022065050S R424,425 00D9630345903 R,FIXED 2WJ-0.47 FLAME RETARDANT N113136647820S R430,431 00D9630345903 R,FIXED 2WJ-0.47...
Page 146
Ref. No. Part No. Part Name Remarks Q'ty R666 963252004160S POSISTOR 18BC471QB5RB F320184710050S R667 R,FIXED 1WJ-5.6K N113135656220S R674 963125012630S R,METAL FILM 22-J,1W FLAME RETARDANT C060022065050S R683,684 00D9630345903 R,FIXED 2WJ-0.47 FLAME RETARDANT N113136647820S R689,690 00D9630345903 R,FIXED 2WJ-0.47 FLAME RETARDANT N113136647820S R694 R,METAL FILM 3.3K-J,1W C060033265050S R698...
Page 150
Ref. No. Part No. Part Name Remarks Q'ty NOTE : Two kinds of relays can be used. Please choose suitable resistors to each kind of relay. ① .RELAY_A RLY2-5 963682003410S RELAY HL3-2A-12S 12V 5A G680120503020S R20-23 R,CARBON FILM//22-J,1/5W-52RE-AX C00002206P520S ② .RELAY_B RLY2-5 963682002440S RELAY G5PA-28MC 12V G680120502050S...
Page 151
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC103 00D2630553006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630553006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108 963239003420S IC NJM2388F05 J126238800050S D114 00D9630236504 D,SCHOTTKY RB721Q-40...
Page 152
Ref. No. Part No. Part Name Remarks Q'ty CP115 CN,WAFER 17P C125Z1-17 L109012511710S z F105 963652010500S FUSE T1.6A/250V N751501601160S z F106 963652010500S FUSE T1.6A/250V N751501601160S F105A HOLDER,FUSE CLIP G645000050010S F105B HOLDER,FUSE CLIP G645000050010S F106A HOLDER,FUSE CLIP G645000050010S F106B HOLDER,FUSE CLIP G645000050010S...
Page 153
PCB FRONT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC100 00D2631289900 IC AZ4580M J121458000020S IC102 00D2631289900 IC AZ4580M J121458000020S Q100,101 943214500020S TR 2SC 2SC3052 CVT2SC3052 Q102 00D9600133103 TR 2SA KSA916Y J5000916Y0050S Q106 943216500050S TR 2SC RT1N441C CVTRT1N441C Q107,108 963212500030S TR 2SA ISA1530AC1...
Page 155
PCB AUDIO_VIDEO ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC801 963239000650S IC R2A15218FP J084152180010S IC806 963233100020S IC TC4052BFT J040405205510S IC821 232810005504S IC BD7628F-E2 J127762800010S IC822 00D2623445901 IC TC4051BFT J040405105510S IC823 232810005504S IC BD7628F-E2 J127762800010S IC825 963239003470S IC NJM2586AM J171258600010S IC826 963233100020S IC TC4052BFT...
Page 157
PCB HDMI ASS'Y NOTE: When the following are replaced, always rewrite with updated firmware using DFW. (Refer to "PROCEDURE FOR UPGRADING THE VERSION OF THE FIRMWARE" (41 page).) • PCB HDMI ASSY • IC11 (MX25L3206EM2I-12G • IC41 (R5F64169DFDFP) • U7 (EN29LV160BB-70TIP) •...
Need help?
Do you have a question about the AVR-1712 and is the answer not in the manual?
Questions and answers