Moxa Technologies NPort 5400 Series Quick Installation Manual

NPort 5400 Series
Quick Installation Guide
Fourth Edition, January 2007
1. Overview
Welcome to Moxa NPort 5400, a 4 port communication device that
allows you to control RS-232 (for NPort 5410), RS-422/485 (for NPort
5430/5430I) or RS-232/422/485 (for NPort 5450/5450I) serial devices
over a TCP/IP based Ethernet.
NPort 5400 Series is a MOXA Green Product. Moxa's Green Products
satisfy the RoHS directive of the European Parliament, and accordingly,
do not contain cadmium and cadmium compounds, hexavalent chromium
compounds, lead and lead compounds, mercury and mercury compounds,
PBBs (polybrominated biphenyls), or PBDEs (polybrominated diphenyl
ethers).
2. Package Checklist
Before installing NPort 5400, verify that the package contains the
following items:
1 NPort 5400 4-Port Serial Device Server
NPort Document & Software CD
NPort 5400 Series Quick Installation Guide
Product Warranty
Optional Accessories
DK-35A For 35 mm DIN-Rail; includes 4 screws
Notify your sales representative if any of the above items is missing or
damaged.
3. Hardware Introduction
As shown in the following figures, NPort 5410 has 4 Male DB9 ports, for
the RS-232 interface, NPort 5430/5430I has 4 5-pin terminal blocks, for
the RS-422/485 interface, and NPort 5450/5450I has 4 Male DB9 ports,
for the RS-232/422/485 interface.
P/N: 1802054000300
— 1 —
NPort 5410/5450/5450I
Power input
RESET
V+ V-
LAN
RJ45 10/100 Mbps Ethernet port
Terminal Block power input
5410
NP5410_61405
192.168.127.254
Serial Device Server
Port 1 Port 2 Port 3 Port 4
RS-232 RS-232 RS-232 RS-232
Indicator LEDs Input buttons LCM display panel
Male DB9 serial port
NPort 5430/5430I
Power input
RESET
V+ V-
LAN
RJ45 10/100 Mbps Ethernet port
Terminal Block power input
5430
N P 5430_61405
192. 168. 127. 254
Serial Device Server
Port 1 Port 2 Port 3 Port 4
RS-422/785 RS-422/785 RS-422/785 RS-422/785
Indicator LEDs Input buttons LCM display panel
RS-422/485 Terminal Block
T+ T- R+ R- GND T+ T- R+ R- GND T+ T- R+ R- GND T+ T- R+ R- GND
D+ D- D+ D- D+ D- D+ D-
— 2 —
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button.
LED Indicators—NPort 5400's top panel contains six LED indicators,
as described in the following table.
LED Name LED Color LED Function
Steady on: Power is on and NPort is booting up.
Blinking: Indicates an IP conflict, or DHCP
red
or BOOTP server did not respond
properly.
Steady on: Power is on and NPort is
Ready
functioning normally.
Blinking: The NPort has been located by
green
NPort Administrator's Location
function.
off Power is off, or power error condition exists.
orange 10 Mbps Ethernet connection.
green 100 Mbps Ethernet connection.
Link
off Ethernet cable is disconnected, or has a short.
orange Serial port is receiving data.
green Serial port is transmitting data.
P1, P2,
P3, P4
No data is being transmitted or received through
off
the serial port.
LCM Display Panel—When the NPort 5400 unit is powered up, you will
a see a display similar to:
N P 5 4 1 0 _ 6 1 4
1 9 2 . 1 6 8 . 1 2
This is where NP5410_61405 is the server's name, and 192.168.127.254
is the server's IP address.
LCM Panel Operation—There are four buttons on NPort 5400's top
panel used to operate the server's LCM panel. Going from left to right,
the buttons are:
Button Action
Activates the main menu, or returns to a lower level.
MENU
Scrolls up through a list of items shown on the LCM
panel's second line.
Scrolls down through a list of items shown on the LCM
panel's second line.
Selects the option listed on the LCM panel's second line.
SEL
Detailed LCM Panel Operating instructions can be found on the
CD-ROM in the "NPort 5400 Series User's Manual."
— 3 —
0 5
7 . 2 5 4