Modifying Showview Programming - Samsung SV-DVD540 Instruction Manual

VCR
Using the ShowView
OK
GB
1
Timer Method
Standard
ShowView
ShowView
Code
Code : 0 - 9
Correct :
PR Day Start Stop Speed V/P
WE 1 19 : 00 19 : 30 SP Off
: :
: :
: :
: :
STANDBY/ON OPEN/CLOSE
5
32
Before presetting your DVD-VCR:
Switch on both the television and your DVD-VCR
Check that the date and time are correct
Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1 To enter a ShowView , press the TIMER button.
and OK or ❿ buttons to select
Press the or
❷
Result: A message is displayed to allow you to enter the
ShowView code.
If all six programmes have been set, the message
is full is displayed. Refer to page 35 if you wish to
cancel a preset recording.
2 Press the numeric buttons to enter the code opposite the
programme that you wish to record in your television magazine.
If you wish to correct the code that you are
ShowView
entering:
Press the ➛ button until the digit to be corrected is
cleared
Enter the correct digit
3 Press the OK button.
Result: The information concerning the programme is
displayed.
When using the function for the first time with
ShowView
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the or buttons. Refer to the following page
❷
if:
The programme number or times flash
You wish to modify the programme
4 If the programme and times are correct, press the RETURN
button.
5
Press the STANDBY/ON button to activate the timer.
6 Refer to page 35 if you wish to:
Check that your DVD-VCR has been programmed correctly
Cancel a preset recording
The numbers next to each TV programme listing are
ShowView code numbers, which allow you to
programme your videorecorder instantly with the
remote control. Tap in the ShowView code for the
programme you wish to record.
™ ShowView is a trademark of Gemstar Development Corporation. The ShowView system
is manufactured under licence from Gemstar Development Corporation.

Modifying ShowView Programming

If you wish to correct the programme displayed or modify certain elements, such as the recording speed,
you can do so before you press RETURN a second time to confirm.
If you wish to...
Select an input source other
than the tuner (AV1, AV2 or AUX)
ShowView
Timer
Record a programme every day
(Monday to Sunday) at the same time
Record a programme every week
on the same day and at the same time
Extend the recording time
Select the recording speed
Select the PDC recording
Then...
Press the ➛ or ❿ buttons, until the
PR selection mode.
Press the INPUT SEL. button one or more times to change the
input source selection.
Result: The programme number is replaced by:
•
The AV1, AV2 or AUX source using the INPUT
SEL. button for a satellite tuner or external video
source
The input source must be selected before changing any other
value.
Press the ➛ or ❿ buttons, until the selection mode.
Day
Press the or buttons, until the (Daily) value is
DLY
❷
displayed.
Press the ➛ or ❿ buttons, until the
Day selection mode.
Press the or buttons, until the W- (Week) value is
❷
displayed, followed by the required day.
Example: (Weekly Saturday)
W-SA
Press the ➛ or ❿ buttons, until the Stop selection mode.
Press the or buttons to increase or decrease the stop time.
❷
Press the ➛ or ❿ buttons, until the recording speed selection mode.
Press the or buttons until the correct indication is displayed:
❷
• Auto
(Auto Tape Speed Select) : see page 34
• SP
(Standard Play)
• LP (Long Play)
Press the ➛ or ❿ buttons, until the PDC off mode.
Press the or buttons until the "On" indication is displayed.
❷
Do not select PDC unless you are sure the programme you
wish to record is broadcast with PDC. If you do set PDC On
(by selecting "On" in the right - hand column on the screen),
then you must set up the start-time EXACTLY according to
the published TV schedule. Otherwise the timer recording
won't take place.
VCR
GB
33