Table of Contents
Advertisement
Quick Links
Acumen
Recharge E & V
™
Battery operated electric projection screen
Overview - Components
Electrical Knock-outs
(Top and Back)
Motor Wiring
Access Panel
Read and understand all warnings
Contents
Overview - Components .......................................................................................1
PLEASE READ - Safety Information ....................................................................2
Section 1 - Charging Motor .................................................................................2
Charging Accessories..............................................................................................2
Section 2 - Fascia Removal .................................................................................3
Section 4 - Hanging Screen .................................................................................4
Section 5 - Wake Up Motor
Removable Fascia
CAUTION
(Page 2 of this document)
e ....................................... 6
Wall / Ceiling
Mounting
Brackets
before beginning installation.
Section 6 - Handheld Remote Control ...............................................................6
Section 7 - Check Battery Charge Level ...........................................................6
Section 8- Set Motor Limits .................................................................................7
Section 9 - Tab-Tension Adjustment Procedure ..............................................8
Section 10 - Charging Options ............................................................................8
..............3
Section 12 - Dimensions
- Wall & Ceiling Bracket Dimensions for Mounting
BACK PAGE
INSTRUCTIONS
INSTALLATION & OPERATION
Extruded
Aluminum
Case
..........................10
(Tab-Tensioned Surface Shown)
If you have any difficulties installing or servicing your
Acumen, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
|
© 2020 All Rights Reserved
FORM: AcumenRC_E_V_Inst20
TOOLS
REQUIRED
PENCIL
POWER DRILL
TAPE MEASURE
LEVEL
HARDWARE
(by others)
/
"
3
32
HEX WRENCH
........................9
Advertisement
Table of Contents
Related Manuals for Draper Acumen Recharge E
Summary of Contents for Draper Acumen Recharge E
-
Page 1: Table Of Contents
(Exiting Sleep Mode) If you have any difficulties installing or servicing your Acumen, call your dealer or Draper, Inc. Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385 draperinc.com | 765.987.7999 | 800.238.7999 © 2020 All Rights Reserved FORM: AcumenRC_E_V_Inst20... -
Page 2: Please Read - Safety Information
9. Do not wire motors in parallel without written permission from Draper, Inc. 2. Installation and calibration of the unit should only be performed by an 10. During testing or operation, carefully watch the surrounding area for any authorized, qualified, and experienced professional. -
Page 3: Section 2 - Fascia Removal
Acumen Recharge E & V ™ page 3 of 12 Section 2 - Fascia Removal MUST BE DONE PRIOR TO REMOVAL OF SHIPPING BRACKETS To remove fascia: 1. Remove the screws from bottom lip at each end of the fascia using 3/32” hex wrench. 2. -
Page 4: Section 4 - Hanging Screen
Acumen Recharge E & V ™ page 4 of 12 Section 4 - Hanging Screen Section 4.1 - General: Appropriate hardware Wall Mounting Brackets (minumum of 2) must be attached to the case regardless of mounting method. provided by installer. Appropriate 2. - Page 5 Acumen Recharge E & V ™ page 5 of 12 Ceiling Bracket Assembly Section 4.3 - Ceiling Installation: 1. Attach Ceiling Brackets to Mounting Brackets using the provided hardware (see figure at right) ACUMEN 2. Secure the Ceiling Brackets to the ceiling using appropriate hardware (by others) Ceiling Bracket Assembly Carriage Bolt...
-
Page 6: (Exiting Sleep Mode) E
Section 5 - Wake Up Motor (Exiting Sleep Mode) Each Acumen ReCharge battery motor will come preprogramed from Draper. Upon leaving the factory the motor is placed into “Sleep Mode” to avoid accidental operation during shipping. It is necessary to “Wake” the motor before operation and setup. -
Page 7: Section 8- Set Motor Limits
Acumen Recharge E & V ™ page 7 of 12 Section 8- Set Motor Limits Move screen to desired Important: After highest or lowest setting limits, motor To save upper limit, To save lower limit, position by pressing will automatically hold both UP and STOP. -
Page 8: Section 9 - Tab-Tension Adjustment Procedure
END OF END OF DOWEL DOWEL Please Note: The Draper Tab-Tensioning System is factory-set, and under Figure 9 normal circumstances will not require field adjustment. If wrinkles are observed, however, follow the adjustment procedure shown in Figure 9. CAUTION: Do not touch or bend surface. -
Page 9: Section 11 - 3Rd Party Control System Components
Acumen Recharge E & V ™ page 9 of 12 Section 11 - 3rd Party Control System Components (optional) RF Single Channel Wall Switch - C112.257 ARC REPEATER C072.057 Charger C072.058 Please Note: Consult user manual provided with Dry Contact Transmitter - C156.264 each component for detailed useage instruction. - Page 10 Acumen Recharge E & V ™ page 10 of 12 Section 12 - Dimensions (Tab-Tensioned Surface Shown) Case Length Varies 18" Max. 18" Max. Centered Ceiling Bracket (457mm) (457mm) ACUMEN " End of Case Dimensions - Shown with Ceiling Bracket "...
- Page 11 Acumen Recharge E & V ™ page 11 of 12...
Need help?
Do you have a question about the Acumen Recharge E and is the answer not in the manual?
Questions and answers