Advertisement
Quick Links
warwick
2 door accent cabinet
style # FKWWCB2DBR (fawn brown)
dpci # 249-16-8735
tcin # 52166593
style # FKWWCB2DWH (white)
dpci # 249-17-3052
tcin # 54187460
>>
assembly instructions
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Target Warwick FKWWCB2DBR
Summary of Contents for Target Warwick FKWWCB2DBR
- Page 1 # FKWWCB2DBR (fawn brown) dpci # 249-16-8735 tcin # 52166593 style # FKWWCB2DWH (white) dpci # 249-17-3052 tcin # 54187460 >> assembly instructions © 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
-
Page 2: Before You Begin
Congratulations on your latest Target purchase. Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you. All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time. - Page 3 table of contents introduction hardware parts list assembly 6-12 how to adjust the door hinges QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.
- Page 4 hardware (H1) x 12 (H2) x 8 (H3) x 8 (H4) x 19 (H5) x 4 (H6) x 2 wooden dowel bolt lock washer pan head screw pull bolt pull (H7) x 4 (H8) x 2 (H9) x 1 (H10) x 4 (H11) x 16 (H12) x 1 shelf support...
-
Page 5: Exploded Diagram
exploded diagram ITEM DESCRIPTION QUANTITY top panel left side panel right side panel bottom panel bottom rail back panel shelf door... - Page 6 step 1: attach top panel, bottom panel, and bottom rail to side panels (H1) x 12 (H2) x 8 wooden dowel bolt (H3) x 8 (H16) x 8 (H9) x 1 lock washer washer allen key notched edge 1.1. Carefully tap small wooden dowels into place in top panel, bottom panel, and bottom rail. Leave 1/2” of the dowels sticking out. 1.2.
- Page 7 step 2: secure bottom rail (H8) x 2 large flat head screw 2.1. Align large flat head screws with pre-drilled holes to attach bottom rail to side panels. Do not over tighten screws..
- Page 8 step 3: attach back panel **FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT** Begin by installing all of the screws along one edge of the back panel. Next, using a square or tape measure, make sure that the cabinet is square.
- Page 9 step 4: install adjustable shelf (H7) x 4 shelf support 4.1. Insert shelf supports into desired hole. Different holes accommodate different shelf heights. 4.2. Angle shelf to fit between the rails and set on top of shelf supports.
- Page 10 step 5: attach doors to cabinet (H11) x 16 (H10) x 4 small flat hinge head screw (H5) x 4 (H6) x 2 pull bolt pull 5.1. Align small flat head screws with pre-drilled holes to attach hinge to door. Do not over tighten screws. 5.2.
- Page 11 step 6: install anti-tip kit (H15) (H12) Position against wall (H14) Mark position of strap hole on wall e on wall (H16) Drill 1/4” hole Tap in wall anchor (H16) (H13) Fasten anti-tip strap with wall screw provided (H15) x 1 (H14) x 1 (H12) x 1 (H13) x 1...
- Page 12 how to adjust door alignment Tips for proper door alignment: -Adjustable levelers will reduce minor door mis-alignments caused by an uneven floor. -Use a level to determine if the cabinet top is level. If not, start with the levelers retracted and adjust them as needed.To retract the levelers turn them counterclockwise.
- Page 13 l b s l b s e l f e l f 1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury. 2.
- Page 14 SALICE SALICE 600 Series Adjustment Instructions 600 Series Adjustment Instructions Height Adjustment is achieved by loosening the two screws indicated by the arrows. Once all plates are loosened, the door can be repositioned vertically. The screws are then tightened when the door is in the desired position. Depth Adjustment is achieved by loosening the center screw indicated by the arrow.
- Page 15 LIFETIME GUARANTEE AND LIMITED WARRANTY* Salice America, Inc., warrants that all hinges and/or Salice products contained in Quality That Lasts A Lifetime this product, (but not the product itself) against defects in material and workman- ship for as long as the original consumer purchaser owns the products. Salice will send the original consumer purchaser a new Salice hinge to replace any defective Salice hinge subject to this warranty without charge.
- Page 16 © 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Need help?
Do you have a question about the Warwick FKWWCB2DBR and is the answer not in the manual?
Questions and answers