ZyXEL Communications ZyXEL ZyWALL 2WG User Manual page 63

Table 3 Web Configurator HOME Screen in Router Mode (continued)
LABEL
Interfaces
Status
IP/Netmask
IP Assignment
Renew
Security Services
Content Filter
Expiration Date
Web Site Blocked
3G WAN Interface
Status
show detail.../hide
detail...
ZyWALL 2WG User's Guide
DESCRIPTION
This is the port type.
Click "+" to expand or "-" to collapse the IP alias drop-down lists.
Hold your cursor over an interface's label to display the interface's MAC address.
Click an interface's label to go to the screen where you can configure settings for
that interface.
For the LAN, DMZ and WLAN ports, this displays the port speed and duplex
setting. Ethernet port connections can be in half-duplex or full-duplex mode. Full-
duplex refers to a device's ability to send and receive simultaneously, while half-
duplex indicates that traffic can flow in only one direction at a time. The Ethernet
port must use the same speed or duplex mode setting as the peer Ethernet port in
order to connect.
For the WAN 1 and the Dial Backup ports, it displays the port speed and duplex
setting if you're using Ethernet encapsulation or the remote node name
(configured through the SMT) for a PPP connection and Down (line is down or
not connected), Idle (line (ppp) idle), Dial (starting to trigger a call) or Drop
(dropping a call) if you're using PPPoE encapsulation.
For the WAN 2 interface, it displays Connected when the 3G connection is up,
Connecting when the 3G card is trying to connect to a network but has not
received a response from the base station, Ready to Connect when the 3G
connection is idle, Initializing when the ZyWALL is configuring the 3G card with
AT commands, Disconnecting when the ZyWALL is dropping the 3G connection
or Down when the 3G connection is down.
This shows the port's IP address and subnet mask.
For the WAN, if the ZyWALL gets its IP address automatically from an ISP, this
displays DHCP client when you're using Ethernet encapsulation and IPCP Client
when you're using PPPoE or PPTP encapsulation. Static displays if the WAN
port is using a manually entered static (fixed) IP address.
For the LAN, WLAN or DMZ, DHCP server displays when the ZyWALL is set to
automatically give IP address information to the computers connected to the LAN.
DHCP relay displays when the ZyWALL is set to forward IP address assignment
requests to another DHCP server. Static displays if the LAN port is using a
manually entered static (fixed) IP address. In this case, you must have another
DHCP server on your LAN, or else the computers must be manually configured.
For the dial backup port, this shows N/A when dial backup is disabled and IPCP
client when dial backup is enabled.
If you are using Ethernet encapsulation and the WAN port is configured to get the
IP address automatically from the ISP, click Renew to release the WAN port's
dynamically assigned IP address and get the IP address afresh. Click Dial to dial
up the PPTP, PPPoE, 3G WAN or dial backup connection. Click Drop to
disconnect the PPTP, PPPoE, 3G WAN or dial backup connection.
This is the date the category-based content filtering service subscription expires.
This displays License Inactive when the ZyWALL is not registered or the
subscription service is not activated. Click the field label to go to the screen where
you can update your service subscription.
This displays how many web site hits the ZyWALL has blocked since it last
started up. Disable displays when the feature is not activated. Not Supported
displays when the ZyWALL is not registered. Click the field label to go to the
screen where you can enable this feature.
The fields below display when a 3G card is inserted and WAN 2 is enabled.
Click show detail... to see more information about the 3G connection and 3G
card. Click hide detail... to display less information about the 3G connection and
3G card.
Chapter 2 Introducing the Web Configurator
63