GE Monogram Installation Instructions Manual
Automatic icemaker
Hide thumbs
Also See for Monogram:
- Owner's manual (45 pages) ,
- Use and care manual (32 pages) ,
- Dimensions and installation information (2 pages)
Subscribe to Our Youtube Channel
Related Manuals for GE Monogram
Summary of Contents for GE Monogram
- Page 1 ® GE Monogram Automatic Icemaker Installation Instructions Models ZDI15 ZDIS15 monogram.com...
-
Page 2: Table Of Contents
GE edition. Appliance Warranty. See the Use & Care Guide for warranty information. For Monogram local service in your area, 1-800-444-1845. • Use this appliance only for its intended For Monogram service in Canada, call purpose. -
Page 3: Design Information
Design Information Automatic Icemaker ZDI15, ZDIS15 The ice machine may be installed below a Models Available in black, white and stainless steel. countertop or used free-standing. Available Cutout & Cutout dimensions shown allow for a full door swing. When installing a 3/4" thick custom Product door panel, additional clearances at the sides may be required. -
Page 4: Installation
Installation Automatic Icemaker Advance CAUTION PRUDENCE Planning Due to excessive weight, TWO PEOPLE Å cause de son poids élevé, IL FAUT DEUX PERSONNES POUR D´PLACER ET IN- ARE REQUIRED TO MOVE AND INSTALL STALLER CE DISTRIBUTEUR DE GLACE. THIS ICE MACHINE. Choose the location: –... -
Page 5: Remove Packaging
Installation Automatic Icemaker • Lay the carton on rear face and break open Remove the bottom flap. Packaging • Set the carton upright with all four bottom flaps outward. and Parts • Lift carton up and off icemaker. • Remove all tape and packaging material from the outside and inside of the cabinet. -
Page 6: Water Supply
Installation Automatic Icemaker • A cold water supply is required for icemaker Water operation. The water pressure must be Supply between 20 and 120 p.s.i. 3" 11-1/2" • Route 1/4" OD copper tubing between 28-1/2" house cold water line and the water connec- 9"... -
Page 7: Connect The Drain
Installation Automatic Icemaker This ice machine is equipped with a gravity Connect drain to prevent water from flowing back into the Drain the ice machine storage bin and potentially flowing onto the floor. A floor drain is acceptable. The ideal installation has a standpipe with a 2”... -
Page 8: Reverse Door Swing
Installation Automatic Icemaker Parts Identification: (For Reference Only) Reverse Tools Required: Parts Supplied: • 1/4” and 5/16” wrench 4 plug buttons Door • Flat putty knife Swing • Phillips screwdriver Hinge Pin Handle Screw Important: 4 Hinge Screws (on some models) Disconnect power to the ice machine. - Page 9 ZIP75WW, ZIP75BB Kit For 3/4" Custom Panel Before you begin – Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference.
- Page 10 Set screws aside. Install supplied door handle (if used) Discard handle. • Install the new supplied handle with original • The Monogram nameplate is held in place screws. with adhesive. Remove the nameplate. Step 3: Mark mounting screw locations.
- Page 12 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845.
Need help?
Do you have a question about the Monogram and is the answer not in the manual?
Questions and answers