GE Monogram ZDI15 Installation Instructions Manual
Automatic icemaker
Hide thumbs
Also See for Monogram ZDI15:
- Use and care manual (46 pages) ,
- Owner's manual (24 pages) ,
- Design and installation manual (12 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for GE Monogram ZDI15
Summary of Contents for GE Monogram ZDI15
- Page 1 Installation Instructions Automatic Icemaker ZDI15 ZDIS15 Design Guide with Installation Instructions Monogram:...
-
Page 2: Table Of Contents
Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner's Manual for warranty information. • Use this appliance only for its intended purpose. -
Page 3: Design Information
Design information MODELS AVAILABLE ZDI15, ZDIS15 The icemaker may be installed below a countertop or Available in black, white and stainless steel, used free-standing. CUTOUT & PRODUCT DiMENSiONS Cutout dimensions shown allow for a full door swing. Additional Clearances: • The installation of a 3/4"thick custom panel will require an additional 1-1/2"wide filler strip on the hinge side. -
Page 4: Advance Planning
Installation instructions ADVANCE PLANNING ADVANCE PLANNING (cont.) CAUTION: Dueto excessive Before you begin: weight, TWO PEOPLEARE REQUIRED TO 1. If a custom panel is to be installed, follow the MOVE AND iNSTALL THiS ICEMAKER. instructions shown on pages 9 and 10. Failure to do so can result in back or -Order ZIP75 (black or white) panel kit. -
Page 5: Power Supply
Installation instructions POWER SUPPLY REMOVE PACKAGING AND PARTS • Lay the carton on rear face WARNING: and break open the bottom FOR PERSONAL SAFETY,THIS APPLIANCE (Please read carefully). flap. MUST BE PROPERLYGROUNDED. Failure to • Set the carton upright follow these instructions can result in death, fire, or electrical shock. -
Page 6: Water Supply
Allow enough to accommodate This icemaker is moving unit forward for service. equipped with a gravity NOTE: The only GE approved plastic tubing is supplied in drain to prevent water the GE SmartConnect Refrigerator Tubing kits. Do not... -
Page 7: Connect Water Supply
• Remove the hinge pin from the top hinge. Icemal(er • Lift the door off of the bottom hinge. Place the hinge GE SmartConnect'=Tubing: pin back into the top hinge. * Insert the molded end of the tubing intothe icemaker connection. - Page 8 Installation instructions REVERSE THE DOOR SWING (cont.} REVERSE THE DOOR SWING (cont.) To reverse the door catch: Reverse the hinges: • Using a flat putty knife, remove the screw hole plugs • Remove the plastic screws opposite the door hinges, top and bottom. Set aside. from the opposite side of the door.
- Page 9 Installation instructions for ZIP75WW, ZIP75BB Kit • BEFORE YOU BEGIN: NOTE: If installing a 3/4"trimless custom panel, a 1-1/2"wide filler strip may be required. The filler strip Read these instructions completely and carefuJJy. will act as a spacer between the icemaker case and •...
- Page 10 Installation instructions for ZIP75WW, ZIP75BB Kit STEP 5 SECURE SIDE TRIM PIECES TO CUSTOM PANEL TO THE iCE MACHINE • Lay the custom panel appearance-side-down on a clean surface. STEP 2 REMOVE HANDLE • Align top and bottom side trim to the custom AND NAMEPLATE panel sides.
- Page 11 Notes...
- Page 12 ( enel-al Ele(lri(. Thel-et_n-e, malel-ials, al)l)earal_(e Sl)e(ifi(aliol_S _11(_ stl|)i(..1 (hange wilhoul noli(e. Monogram: Pub.No. 49-60016-4 ] GE Col_sumer& Industria / GEAppliancos PartNo. 197D2522PO01 Gotle_] Electric _mpang Louisdlle, KY40225 2217409 02-06JR go com Printedin tl_e United States ©2000 GE Compmly...
Need help?
Do you have a question about the Monogram ZDI15 and is the answer not in the manual?
Questions and answers