Zenoah BCZ2600SU Owner's/Operator's Manual
  1. Manuals
  2. Brands
  3. Zenoah Manuals
  4. Brush Cutter
  5. BCZ2600SU
  6. Owner's/operator's manual
Zenoah BCZ2600SU Owner's/Operator's Manual

Zenoah BCZ2600SU Owner's/Operator's Manual

Zenoah brush cutter owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER / OPERATOR MANUAL
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS :
BCZ2600S
DRIVE UNIT 300001 and up
BCZ2600SU
DRIVE UNIT 300001 and up
BCZ2600SW DRIVE UNIT 300001 and up
BRUSHCUTTERS
BCZ2600S
BCZ2600SU
BCZ2600SW
BCZ2600S
BCZ2600SU
BCZ2600SW
WARNING
Before using our brushcutters,
please read this manual carefully to
understand the proper use of your
unit.
ENGINE UNIT 50100000 and up
ENGINE UNIT 50100000 and up
ENGINE UNIT 50100000 and up
848-B50-93A1 (501)

Advertisement

Table of Contents
loading

Related Manuals for Zenoah BCZ2600SU

Summary of Contents for Zenoah BCZ2600SU

  • Page 1 OWNER / OPERATOR MANUAL BRUSHCUTTERS BCZ2600S BCZ2600SU BCZ2600SW BCZ2600S BCZ2600SU WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. APPLICABLE SERIAL NUMBERS : BCZ2600S DRIVE UNIT 300001 and up...

  • Page 2: Table Of Contents

    SAFETY FIRST Instructions contained in warnings within this manual marked with a critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■...

  • Page 3: Parts Location

    ■ BCZ2600S/BCZ2600SU/BCZ2600SW Overall size(LxWxH) BCZ2600S/BCZ2600SU ····································· 70.5(1790)x9.8(250)x12.2(310) in(mm) BCZ2600SW ····················································· 70.5(1790)x24.8(630)x19.1(485) in(mm) Dry weight w/o acc. BCZ2600S/BCZ2600SU ················································· 11.7 lbs (5.3kg)/11.1 lbs (5.1kg) BCZ2600SW ···························································································· 13.0 lbs (5.9kg) Engine Type······················································································ Air-cooled 2-stroke gasoline Model········································································································ Zenoah GZ25N Displacement ······················································································· 1.6cu-in (25.4cm Max.

  • Page 4: Warning Labels On The Machine

    3. Warning labels on the machine (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helpers 15 meters away from the brushcutter IMPORTANT If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s).

  • Page 5: Symbols On The Machine

    4. Symbols on the machine IMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO 2005 U.S. EPA REGULATIONS FOR SMALL NONROAD ENGINES. COMPLIANCE PERIOD : CATEGORY A ENGINE FAMILY : 5KZXS.0254QR ; EM ENGINE DISPLACEMENT : REFER TO OWNER’S MANUAL FOR MAINTE- NANCE SPECIFICATIONS AND ADJUSTMENTS.

  • Page 6: For Safe Operation

    5. For safe operation 6  1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the product.
  • Page 7 5. For safe operation b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product.
  • Page 8 5. For safe operation 8  ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area.
  • Page 9 5. For safe operation WARNING Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position.
  • Page 10 5. For safe operation 10  • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2.
  • Page 11 5. For safe operation refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank.

  • Page 12: Set Up

    6. Set up (BCZ2600S, BCZ2600SU) 12  ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch...
  • Page 13 6. Set up (BCZ2600SW) ■ MOUNTING ENGINE (SE5) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw.
  • Page 14 6. Set up SE10 SE11 14  ■ INSTALLING CUTTING HEAD (SE10) 1. While locking the gear shaft, by inserting the supplied tool into the upper holder on the gear box, loosen and remove the hexagon nut(left- handed) 2. Fit the holder attached to the upper holder. Then screw in the cutting head to the gear shaft over the holders.

  • Page 15: Fuel

    7. Fuel WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine.
  • Page 16 7. Fuel again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture.

  • Page 17: Operation

    8. Operation BCZ2600S BCZ2600SU BCZ2600SW ■ STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.
  • Page 18 8. Operation .04 in (1~2mm) 18  ■ STOPPING ENGINE (OP3) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the STOP position. IMPORTANT • Except for an emergency, avoid stopping the engine while pulling the throttle lever.
  • Page 19 8. Operation crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the unit so the head is off the ground and is tilted about 20 degrees toward the sweep direction. (OP7) 2.

  • Page 20: Maintenance

    9. Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. ■ MAINTENANCE CHART system/compornent fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent clean muffler, spark arrester, cylinder exhaust port clean...
  • Page 21 9. Maintenance .025 in 0.655mm on the housing, press the cap against the housing until it clicks. WARNING • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury.
  • Page 22 9. Maintenance 22  ■ MUFFLER WARNING • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire.
  • Page 23 9. Maintenance themselves to the brushcutter. Failing to do so could cause the muffler to become overheated, and that this in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use.

  • Page 24: Storage

    10. Storage 24  • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.

  • Page 25: Optional Blade Usage

    11. Optional blade usage OPT1 CUTTER APPLICATION CHART Under growth Heavy weeds Light weeds Grass OPT2 9” 22-tooth: 8” 8-tooth: SST229 SGB088 9” 24-tooth: 9” 8-tooth: SST249 SGB089 ■ CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the object to be cut. (OPT1) •...
  • Page 26 OPT3 BCZ2600S BCZ2600SU OPT4 BCZ2600S BCZ2600SU OPT5 OPT6 26  IMPORTANT [ BCZ2600S, BCZ2600SU ] Change to the debris guard which is suitable for the metal blade. (OPT3) TIGHTENING TORQUE: (1)Guard Ass’y: 6489-24000 (2)Guard: 6489-24110 (3)Plate Comp.: 6489-24200 (4)Plate: 6489-24210...
  • Page 27 11. Optional blade usage OPT7 OPT8 speed is too low, or the blade cuts too deep into weeds. Adjust the engine speed and cutting depth according to the condition of object. WARNING • If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit.
  • Page 28 11. Optional blade usage 28  you understand what causes kick out, how you can reduce the chance of kick out and how you can remain in control of the unit if kick out does occur. 1. What causes kick out: •...
  • Page 29 11. Optional blade usage OPT9 ■ MAINTENANCE BLADE • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point (OPT9) : 1. Keep the end corner sharp. 2.

  • Page 30: Troubleshooting Guide

    12. Troubleshooting guide Case 1. Starting failure CHECK fuel tank fuel filter carburetor adjustment screw ➞ sparking (no spark) spark plug Case 2. Engine starts but does not keep running/Hard re-starting. CHECK fuel tank carburetor adjustment screw muffler,cylinder (exhaust port) ➞ carbon is built-up air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our RedMax service shop in your area.

  • Page 31: Parts List

    13. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
  • Page 32 13. Parts list Fig.1 DRIVE UNIT BCZ2600S (S/N 300001 and up) BCZ2600SU (S/N 300001 and up) 32 ...
  • Page 33 BCZ2600S (S/N 300001 and up) Fig.1 DRIVE UNIT BCZ2600SU (S/N 300001 and up) Key# Description PIPE-COMP, 1500xø24xT1.7 PIPE-COMP, 1500xø24xT1.5 SHAFT, 1536xø7, spline 7T GEARCASE-ASSY • GEARCASE • BEARING • BEARING • RING • SEAL • SHAFT • GEAR • NUT, M10 •...
  • Page 34 13. Parts list Fig.2 DRIVE UNIT BCZ2600SW (S/N 300001 and up) 34 ...
  • Page 35 Fig.2 DRIVE UNIT BCZ2600SW (S/N 300001 and up) Key# Description PIPE-COMP, 1500xø24xT1.7 SHAFT, 1536xø7, spline 7T GEARCASE-ASSY • GEARCASE • BEARING • BEARING • RING • SEAL • SHAFT • GEAR • NUT, M10 • PINION • BEARING • BEARING •...
  • Page 36 13. Parts list Fig.3 ENGINE UNIT BCZ2600S (S/N 50100000 and up) BCZ2600SU (S/N 50100000 and up) BCZ2600SW (S/N 50100000 and up) 36 ...
  • Page 37 BCZ2600S BCZ2600SU (S/N 50100000 and up) Fig.3 ENGINE UNIT BCZ2600SW (S/N 50100000 and up) Key# Description CYLINDER GASKET, base BOLT, M5x22 INSULATOR GASKET, insulator GASKET, carburetor SCREW, M5x20 REEDVALVE (S)-A • VALVECASE (S) • REEDVALVE • STOPPER • SCREW, M3x8...

  • Page 38: Limited Warranty

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
  • Page 39 ZENOAH AMERICA INC. au (770)-381-5147 Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie pour vous.
  • Page 40 KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 © Printed in U.S.A.

This manual is also suitable for:

Bcz2600sw

Table of Contents