Related Manuals for Zenoah BCZ4500/5000CL
Summary of Contents for Zenoah BCZ4500/5000CL
- Page 1 BCZ4500DL / BCZ4500DW / BCZ4500CL / BCZ5000DL / BCZ5000DW / BCZ5000CL 848JL593A0 (509) OWNER’S MANUAL BRUSHCUTTERS BCZ4500DL / DW BCZ5000DL / DW BCZ4500 / 5000CL...
-
Page 2: Table Of Contents
BCZ4500DL / BCZ4500DW / BCZ4500CL / BCZ5000DL / BCZ5000DW / BCZ5000CL SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. -
Page 3: Fuel Tank
Spark plug Fuel tank capacity Starter Clutch Reduction ratio Cutting head rotating direction *When using Zenoah genuine oil Specifications are subject to change without notice. 3. Warning labels on the machine Read owner’s manual before oper- ating this machine. Wear head, eye and ear protec- tion. -
Page 4: For Safe Operation
BCZ4500DL / BCZ4500DW / BCZ4500CL / BCZ5000DL / BCZ5000DW / BCZ5000CL 5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. - Page 5 If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized KOMATSU ZENOAH servicing dealer for re- pair. USING THE PRODUCT IMPORTANT Cut only materials recommended by the manufacturer.
- Page 6 KOMATSU ZENOAH prod- ucts or products which have been certified by KOMATSU ZENOAH for use with the KOMATSU ZENOAH product. 4. In the event that any part must be replaced or any maintenance or...
-
Page 7: Set Up
6. Set up INSTALLING HANDLE (BCZ4500DL/5000DL) • Set the handle and the barrier on the bracket. Attach them with the 4bolts provided securely. INSTALLING HANDLE (BCZ4500DW/5000DW) • Loosen the 4bolts on the upper cap and insert the handle. Retighten the bolts securely. INSTALLING HANDLE (BCZ4500CL/5000CL) •... -
Page 8: Fuel
3 m (10 ft) away from the fueling point before starting the engine. • The Komatsu Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Komatsu Zenoah oil is not available,... -
Page 9: Operation
8. Operation STARTING ENGINE WARNING • The cutting head will start rotating upon the en- gine starts. 1. Feed fuel into the fuel tank and tighten the cap se- curely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects, as it will start rotating upon starting of the engine. - Page 10 If not, it is vary dangerous when you slip or lose your balance. • Be sure to use genuine parts made of Zenoah for blades.In particular, never use special blades such as shredder blades.If you use a special blade, the...
- Page 11 8. Operation CUTTING METHOD (a)Use the front left side cutting. (b) Guide the blade from your right to left with it tilted slightly to your left. (c) When mowing a wide area, start working from your left end to avoid interference of cut grass. (d) The blade may be seized by weeds if the engine speed is too low, or the blade cuts too deep into weeds.
-
Page 12: Maintenance
• Make the right and left lines the same length when using the nylon line head. (Be sure to install the genuine Zenoah debris guard when using the nylon line head.) • If the lengths of the right and left lines are different, the balance of the nylon line head will be disrupted, resulting in increased vibration and product damage. - Page 13 • Starting failure and misfiring are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a re- placement plug, use the correct type specified by KOMATSU ZENOAH. (1) Paper element (1) Fuel filter...
-
Page 14: Storage
BCZ4500DL / BCZ4500DW / BCZ4500CL / BCZ5000DL / BCZ5000DW / BCZ5000CL 9. Maintenance 0.6~0.7 mm • REPLACEMENT PLUG IS A NGK CMR7H. IMPORTANT • Note that using any spark plug other than those des- ignated may result in the engine failing to operate prop- erly or in the engine becoming overheated and dam- aged. -
Page 15: Troubleshooting Guide
(exhaust port) air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our KOMATSU ZENOAH Limited warranty Should any failure occur on the product under normal oper- ating conditions within the applicable warranty period, the failed part will be replaced or repaired free of charge by a ®... - Page 16 BCZ4500DL / BCZ4500DW / BCZ4500CL / BCZ5000DL / BCZ5000DW / BCZ5000CL PRINTED ON RECYCLED PAPER PRINTED IN JAPAN...