Mitsubishi Electric 700 Series Installation Manualline page 23

PARAMETER LIST
Pr. Name
180 RL terminal function selection
181 RM terminal function selection
182 RH terminal function selection
183 MRS terminal function
∗8
selection
RES terminal function
184
selection
RUN terminal function
190
selection
191 FU terminal function selection
A,B,C terminal function
192
selection
232 Multi-speed setting (speed 8)
233 Multi-speed setting (speed 9)
234 Multi-speed setting (speed 10) 0 to 400Hz, 9999
235 Multi-speed setting (speed 11) 0 to 400Hz, 9999
236 Multi-speed setting (speed 12) 0 to 400Hz, 9999
237 Multi-speed setting (speed 13) 0 to 400Hz, 9999
238 Multi-speed setting (speed 14) 0 to 400Hz, 9999
239 Multi-speed setting (speed 15) 0 to 400Hz, 9999
240 Soft-PWM operation selection 0, 1
Analog input display unit
241
switchover
244 Cooling fan operation selection 0, 1
245 Rated slip
Slip compensation time
246
constant
Constant-power range slip
247
compensation selection
Earth (ground) fault detection
249
at start
250 Stop selection
20
Initial
Setting Range
Value
0
1
0 to 5, 7, 8, 10,
2
12, 14 to 16, 18,
24, 25, 62, 65 to
24
67, 9999
62
0, 1, 3, 4, 7, 8, 11
0
to 16, 20, 25, 26,
46, 47, 64, 80∗9,
81∗9, 90, 91, 93,
95, 96, 98, 99,
100, 101, 103,
104, 107, 108,
111 to 116, 120,
125, 126, 146,
147, 164, 180∗9,
181∗9, 190, 191,
193, 195, 196,
198, 199, 9999 4
0, 1, 3, 4, 7, 8, 11
to 16, 20, 25, 26,
46, 47, 64, 80∗9,
81∗9, 90, 91, 95,
96, 98, 99, 100,
101, 103, 104,
107, 108, 99
111 to 116, 120,
125, 126, 146,
147, 164, 180∗9,
181∗9, 190, 191,
195, 196, 198,
199, 9999
0 to 400Hz, 9999 9999
0 to 400Hz, 9999 9999
9999
9999
9999
9999
9999
9999
1
0, 1 0
1
0 to 50%, 9999 9999
0.01 to 10s 0.5s
0, 9999 9999
0, 1 0
0 to 100s, 1000
to 1100s, 8888, 9999
9999
Pr. Name
Output phase loss protection
251
selection
255 Life alarm status display
Inrush current limit circuit life
256
display
Control circuit capacitor life
257
display
Main circuit capacitor life
258
display
Main circuit capacitor life
259
measuring
261 Power failure stop selection
267 Terminal 4 input selection
Monitor decimal digits
268
selection
269 Parameter for manufacturer setting. Do not set.
Stop-on contact control
270
selection
Stop-on contact excitation
275 current low-speed multiplying
factor
PWM carrier frequency at
276
stop-on contact
Stall prevention operation
277
current switchover
278 Brake opening frequency
279 Brake opening current
Brake opening current
280
detection time
281 Brake operation time at start
282 Brake operation frequency
283 Brake operation time at stop
286 Droop gain
287 Droop filter time constant
Automatic acceleration/
292
deceleration
Acceleration/deceleration
293
separate selection
Magnitude of frequency
295
change setting
296 Password lock level
297 Password lock/unlock
298 Frequency search gain
Rotation direction detection
299
selection at restarting
Communication operation
338
command source
Communication speed
339
command source
Communication startup mode
340
selection
Communication EEPROM
342
write selection
343 Communication error count
450 Second applied motor
495 Remote output selection
496 Remote output data 1
497 Remote output data 2
Stop mode selection at
502
communication error
Initial
Setting Range
Value
0, 1 1
(0 to 15) 0
(0 to 100%) 100%
(0 to 100%) 100%
(0 to 100%) 100%
0, 1 (2, 3, 8, 9) 0
0, 1, 2 0
0, 1, 2 0
0, 1, 9999 9999
0, 1 0
0 to 300%, 9999 9999
0 to 9, 9999 9999
0, 1 0
0 to 30Hz 3Hz
0 to 200% 130%
0 to 2s 0.3s
0 to 5s 0.3s
0 to 30Hz 6Hz
0 to 5s 0.3s
0 to 100% 0%
0 to 1s 0.3s
0, 1, 7, 8, 11 0
0 to 2 0
0, 0.01, 0.1, 1,
0
10
0 to 6, 99, 100 to
9999
106, 199, 9999
1000 to 9998,
9999
9999, (0 to 5)
0 to 32767, 9999 9999
0, 1, 9999 0
0, 1 0
0, 1, 2 0
0, 1, 10 0
0, 1 0
— 0
0, 1, 9999 9999
0, 1, 10, 11 0
0 to 4095 0
0 to 4095 0
0, 1, 2, 3 0