Zanussi ZHC 916X Instruction Booklet
  1. Manuals
  2. Brands
  3. Zanussi Manuals
  4. Ventilation Hood
  5. ZHC 916X
  6. Instruction booklet
Zanussi ZHC 916X Instruction Booklet

Zanussi ZHC 916X Instruction Booklet

Cooker hood
Hide thumbs Also See for ZHC 916X:
Table of Contents

Advertisement

Quick Links

See also: Instruction Booklet
INSTRUCTION BOOKLET
COOKER HOOD
ZHC 916X

Advertisement

Table of Contents
loading

Related Manuals for Zanussi ZHC 916X

Summary of Contents for Zanussi ZHC 916X

  • Page 1 INSTRUCTION BOOKLET COOKER HOOD ZHC 916X...

  • Page 2: Guarantee Conditions

    If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http:\\www.zanussi.co.uk...

  • Page 3: Important Safety Information

    • Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunction. Refer to your local Zanussi Service Force Centre. Always insist on genuine spare parts.

  • Page 4: Your Appliance

    OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing.
  • Page 5 OPERATING INSTRUCTIONS This cooker hood can be used to recirculate or extract contaminated air. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen.

  • Page 6: Maintenance And Cleaning

    MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning The metal casing, grille and chimney should be cleaned at least once a month to keep it looking like new.
  • Page 7 MAINTENANCE AND CLEANING To Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting The lamps should be replaced with a 220-240V 20W halogen spot lamp.

  • Page 8: Something Not Working

    For general assistance with your appliance or for information on Zanussi products please contact our Customer Care Department. Customer Care Department, Zanussi 55-77 High Street...
  • Page 9 STANDARD GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: •...

  • Page 10: Installation Instructions

    INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: SUITABLE FOR INSTALLATION ABOVE: Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336.

  • Page 11: Installing The Cooker Hood

    INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood.

  • Page 12: Clearance Heights

    INSTALLING THE COOKER HOOD Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, provided the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications.
  • Page 13 INSTALLATION INSTRUCTIONS Draw a vertical line on the wall from the centre of the cooking appliance, using a spirit level and marking pen. This is to ensure the correct level of alignment of the appliance (5). Mark the hole position (1) on the wall 100mm either side of the vertical line ensuring that they are level and that the distance between the lowest point of the hood and the cooking appliance beneath meet the clearance...

  • Page 14: Adjusting Position

    INSTALLATION INSTRUCTIONS Adjusting Position (10) There are 2 adjustable hooks at the rear of the hood, which can be used to adjust its position as follows: Turn screws L until the position of screws N coincides with the lower access holes. Turn the screws N to adjust the vertical and horizontal position of the hood.
  • Page 15 INSTALLATION INSTRUCTIONS Regardless of which type of installation, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. Drilling the shelves Using the template provided, and taking hole B as a point of reference, drill the shelves along the central axis to allow the passage of the chimney.
  • Page 16 INSTALLATION INSTRUCTIONS Air outlet directed upwards (Fig. 2a-b): - Remove the plastic plug from the upper part of the venting grill and replace it on the rear part (Fig. 16). Air outlet directed towards the wall (Fig. 3): - Remove the plastic frame from the air outlet (Fig. 17).

  • Page 17: Ducting Or Re-Circulation Fitting

    INSTALLATION INSTRUCTIONS Fixing the chimney Loosen the screws M fixing the two parts of the chimney and pull the inner section I (Fig. 21) almost all the way out. Remove the protective film Rest the lower section of the chimney in its housing on the top of the hood canopy.

  • Page 18: Electrical Connection And Working Test

    INSTALLATION INSTRUCTIONS Electrical connection and working test: Remove the metal cover by unscrewing the four self tapping screws. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy. Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws.

  • Page 19: Customer Care Department

    Tel: + 353 (0)1 4090751 Email: service.eid@electrolux.ie Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk...
  • Page 20 © Electrolux plc 2002 4329161_12 - 041207...

Table of Contents