Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZHC 700
Summary of Contents for Zanussi ZHC 700
- Page 1 INSTRUCTION BOOKLET COOKER HOOD ZHC 700...
-
Page 2: For The Installer
If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http://www.zanussi.co.uk... -
Page 3: Important Safety Information
Refer to your local • When installed between adjoining wall cabinets the Zanussi Service Force Centre. Always insist on wall cabinets must not overhang the hob. genuine spare parts. • If the room where the hood is to be used contains a... -
Page 4: Your Appliance
YOUR APPLIANCE OPERATING INSTRUCTIONS The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Cooker Hood Controls The cooker hood functions are controlled by three switches located to the right on the underside of the hood immediately in front of the metal grease filters. - Page 5 To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack.
-
Page 6: Maintenance And Cleaning
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. -
Page 7: Charcoal Filters
Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. -
Page 8: Something Not Working
SERVICE AND SPARE PARTS If you require an engineer or spare parts For general assistance with your appliance or contact your local Service Force Centre by for further information on Zanussi products telephoning: please contact our Customer Care Department. Customer Care Department,... -
Page 9: Guarantee Conditions
GUARANTEE CONDITIONS We Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will,... -
Page 10: Installation Instructions
Technical Information DIMENSIONS HEIGHT OF CANOPY: 24cm HEIGHT OF CHIMNEY: (UPPER SECTION) 40cm (LOWER SECTION) 36cm WIDTH OF CANOPY - ZHC 700: 69,8cm DEPTH OF CANOPY: 49cm GROSS - ZHC 700: 18 kg NET - ZHC 700: 14,9kg ELECTRICAL SUPPLY:... -
Page 11: Installing The Cooker Hood
INSTALLING THE COOKER HOOD Please ensure that when the appliance is The manufacturer disclaims any responsibility for installed it is easily accessible to an damage due to incorrect installation of the cooker engineer in the event of a breakdown. hood or if the hood is not installed in compliance with relevant regulations controlling this type of All installations must comply with the local installation. -
Page 12: Fitting The Wall Brackets
Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions. -
Page 13: Fitting The Canopy Hood
Draw a horizontal line through the vertical line at X. X is a distance between the centre of the top and bottom fixing holes on the upper chimney stack. Mark the centre positions for the middle bracket fixing screws (3) at 95mm either of the vertical line (screws not supplied). - Page 14 Venting The hood is more effective when used in the extraction mode (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 125mm (5”). The 120-125mm collar should be fitted onto the ducting spigot to suit UK diameter ducting, and held in position by a jubilee clip (not supplied) used to secure the flexible hose.
-
Page 15: Fitting The Chimney Stack
Fitting the Chimney Stack The chimney stack consists of two sections. Fit the upper section (S) first. Expand the chimney slightly to allow it to be fitted over the brackets (1) and (2), and then secure the chimney stack to bracket (2) using two self tapping screws provided in the fitting kit. - Page 20 436002372_01 040705 © Electrolux plc 2002...