NightStick TAC-300B-K01 Instruction Manual

Instruction Manual
TAC-300B-K01
WARNINGS
• NOT FOR USE ABOVE HAZARDOUS LOCATIONS
• DO NOT use in explosive atmospheres, near flammable liquids, or where explosion
proof lamps are required.
• DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the flashlight.
• DO NOT expose the batteries to water or salt water, or allow the batteries to get wet.
• DO NOT store the batteries with metallic objects that may cause a short circuit.
• Immediately discontinue use of the batteries if they emit an unusual smell, feel hot,
change color, change shape or appear abnormal in any way.
• Keep out of the reach of children.
ASSEMBLY INSTRUCTIONS
The TAC-300B includes the pocket clip and the tail cap switch already attached. The
light can be used immediately as a conventional tactical flashlight once the batteries are
installed. This light may be converted back to this configuration at any time.
1. Remove the pocket clip (Figure 1-B) by unscrewing and removing the light bezel (Figure 1-A).
2. Reinstall the light bezel (Figure 1-A).
3. Remove the tail cap switch (Figure 1-C). NOTE: Keep the tail cap switch and pocket clip
for future use for the light is to be converted back to a conventional tactical flashlight.
4. Install the two included CR123 batteries (Figure 2-A). The positive terminals on each
battery should be oriented in the direction of the Light Bezel.
5. Install the Remote Pressure Switch (Figure 2-B) and tighten into place.
6. Test the operation of the Remote Pressure Switch (Figure 3-C) and the side switch
(Figure 3-D). The Remote Pressure Switch provides momentary On/Off operation of the
light. The side switch provides momentary On/Off operation by pressing slightly on the
button, or constant-on by pressing until the button clicks.
7. Determine where the Quad Lock Mount (Figure 3-B) is to be located on the light, anywhere
along the handle. (Figure 3-A). The mount must remain clear of the Remote Pressure
Switch, otherwise accessing the batteries will require disassembly of the Quad Lock Mount.
8. Once the location of the Quad Lock Mount has been determined for the light, remove all
4 of the cap head screws (Figure 4-B) using the supplied Allen wrench (Figure 4-A).
9. While holding the lower half of the mount (Figure 3-B) in place, press each of the top rails
in to alignment with the lower half and start all 4 of the cap head screws (Figure 4-B).
IMPORTANT: Partially install all 4 cap head screws before fully tightening.
10. Tighten the 4 cap head screws (Figure 4-B) by alternating between each and tightening
a small amount at a time. When all 4 are tightened into place (DO NOT over-tighten), the
gap between the lower half of the mount and the two top rails should be approximately
1/16" and should be equal on both sides.
11. Test fit the Quad Lock Mount on to the mil spec Picatinny or Weaver rail of the long
gun (Figure 8-A). At the same time, determine the desired location of the Remote
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
Pressure Switch (Figure 8-B). NOTE: The Remote Pressure Switch may be attached
to any clean, dry, flat surface on the long gun. The location indicated in Figure 8
is one example. The location you choose will be determined by your weapon's
configuration and personal preferences.
12. Once the location of the Quad Lock Mount (Figure 8-A) and the Remote Pressure
Switch (Figure 8-B) have been determined, clean the location on your weapon where
the Remote Pressure Switch will be located as well as the inside surface of the Remote
Pressure Switch (Figure 7-A) using the supplied Alcohol Swab (Figure 6-A).
13. Attach the Velcro to the inside surface of the Remote Pressure Switch by removing the
®
paper backing on one of the included Velcro
(Figure 7-B).
14. Attached the Quad Lock Mount with the light installed onto the mil spec Picatinny or
Weaver rail of your weapon (Figure 8-A)
15. Attach the other Velcro
it onto the previously cleaned area (Figure 8-B).
NOTE: Do not move or remove the adhesive strips once they have been placed. The
Velcro adhesive requires about 24 hours to make a semi-permanent bond. Do not attempt
®
to separate the two Velcro
OPERATION
The Nightstick Tactical Long Gun Kit is now fully installed and ready for use.
• The Remote Pressure Switch provides momentary On/Off operation of the light only.
Using this switch gives the operator instant control when the light is on and off.
• The side switch provides momentary On/Off operation by pressing slightly on the button,
or constant-on by pressing until the button clicks.
• If the Quad Lock Mount is positioned correctly (see Step 7 above), changing the batteries
may be accomplished without removing the light from the Quad Lock Mount. Depending
on the installation location, it may be possible to change the batteries without removing
the mount from the weapon.
• To change the batteries, first separate the two halves of the Velcro
so that one half stays adhered to your weapon and the other remains attached to the back
side of the Remote Pressure Switch. Next, unscrew the Remote Pressure Switch and
replace the batteries (see Step 4 above).
WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship and
materials for the original purchaser's lifetime. The Limited Lifetime Warranty includes the
LEDs, housing and lenses. Rechargeable batteries, chargers, switches, electronics and
included accessories are warranted for a period of two years with proof of purchase. Normal
wear and failures which are caused by accidents, misuse, abuse, faulty installation and
lightning damage are excluded.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fitness for
a particular purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-product-
support/warranties. Retain your receipt for proof of purchase.
INS-T300B-K01-20
strips (Figure 7-A). Press it firmly into place
®
strip to the weapon by removing the paper backing and pressing
®
sections until it is set.
®
strip from each other
®