Operation - Renkforce RS2W Operating Instructions Manual

G Operating instructions
RS2W radio wall switch, 2 channels
Item no. 1275700 (white)
Item no. 1275701 (black)
Intended use
The radio wall switch can wirelessly switch a suitable receiver of the RS2W radio system (or a
user connected to it) on or off. The radio wall switch is operated via a type "CR2032" battery.
As a special feature the radio wall switch responds back per LED whether the programmed radio
receiver (max. 5 per channel) of the RS2W radio system has received the key commands or not.
Please read the operating instructions carefully and do not discard them. If you pass the product
on to a third party, please hand over these operating instructions as well.
Any use other than that described above will lead to damage to the product and will expose you
to additional risks, such as short circuits, fire, etc. No part of the product may be modified or con-
verted! The safety instructions must be observed at all times!
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Wireless wall switch (with 1x battery "CR2032")
• Operating instructions
Explanation of symbols, inscriptions
This symbol indicates specific risks associated with handling, function or use.
The "arrow" symbol indicates special tips and operating information.
Safety instructions
D amage due to failure to follow these operating instructions will void the warranty!
We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! In such cases, the warranty will
be null and void!
• The unauthorised conversion and/or modification of the product is not permitted for
safety and approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children!
• Do not use this product in hospitals or medical institutions. Although transmitters
of the RS2W system only emit relatively weak radio signals, these may lead to the
malfunctioning of life-support systems. The same may also apply to other areas.
• The product must not get damp or wet!
• Do not use the product in rooms that are under adverse environmental conditions,
where combustible gases, vapours or dust are or may be present! There is a risk of
explosion!
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress.
• Do not carelessly leave the packaging material lying around since this may become
a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or accidental
falls, even from a low height.
Battery notes
• Batteries should be kept out of the reach of children.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by
children or pets. If they are swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Batteries must not be short-circuited, opened or thrown into a fire. There is a risk of explosion!
• Do not recharge normal, non-rechargeable batteries; there is a risk of explosion!
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
Inserting/replacing the battery
Delivery includes a "CR2032" type battery. This is possibly already inserted into the bat-
tery compartment. In this case a protective synthetic strip between battery and battery
contacts prevents early recharge; remove it.
• Remove both rocker switches by inserting a flathead screwdriver between frame and rocker
switch and subsequently levering out both rocker switches carefully.
• Place a battery of type "CR2032" with the correct polarity (or remove the protective synthetic
strip). The plus pole of the button cells points from you outward.
• Snap both rocker switches on again, pay attention to the correct orientation (transparent open-
ing in one of the two rocker switches must be above the LED).
Pay attention to the next chapter "Assembly" in case the wall-mounted switch must be
screwed on, before you snap on the rocker switches.
• The batteries need to be replaced if the range of the radio wall switch is significantly reduced or
the LED no longer lights when the button is pushed.
Assembly
Test the functioning of the radio wall switch and the registered radio receiver before
you securely mount the radio wall switch.
• Adhesive attachment
Use double-sided adhesive tape to attach the radio wall switch to an appropriate surface. This
must be smooth, clean and grease-free.
• Screw assembly
Remove both rocker switches by inserting a flathead screwdriver between frame and rocker
switch and subsequently levering out both rocker switches carefully.
Remove the central section (with the electronics) from the frame by loosening the lateral clips.
The frame can now be attached with 2 - 4 suitable screws and, if appropriate, plugs. Pay atten-
tion when drilling and tightening the screws that no cable or pipes are damaged.
Reassemble the radio wall switch in a reversed order.

Operation

Keep a minimum distance of 20 - 30 cm between the radio wall switch and the radio
receiver.
a) Resetting the radio wall switch
Perform a reset before the initial startup and tune in the radio receiver(s) after that.
A reset also deletes all radio receivers tuned in/saved on the respective channel.
The reset only applies to the respective individual channel - the second channel re-
mains unaffected!
Proceed as follows to perform a reset:
• Press the "O" and "I" buttons at the same time one of the two rocker switches (approx. 3 seconds)
until the LED flashes red (then release rocker switch for 1 - 2 seconds).
• Press the "O" and "I" buttons again for approx. 6 seconds, until the LED flashes blue. Then,
release the rocker switch again.
b) Programming a radio receiver to the radio wall switch
On every radio transmitter channel of the RS2W radio system, up to 5 different radio re-
ceivers (e.g., radio switchable socket) can be programmed. However, do not mix radio
switch and dimmer.
• Switch the radio receiver of the RS2W radio system you want to tune in to via its operator push
button (see operation manual for the respective radio receiver).