Advertisement
Quick Links
Advertisement
Related Manuals for Echogear EGGA-DMAC1
Summary of Contents for Echogear EGGA-DMAC1
- Page 1 #YourGearUpgraded Single Monitor Desk Mount INSTRUCTION MANUAL Model EGGA-DmAc1...
-
Page 2: Important Safety Instructions
If you do not understand these instructions, are a noob or have doubts about the safety of the installation, assembly or use of this product, contact: The Echogear Pros @ 1-855-428-2490 or www.echogear.com. CAUTION: Manufacturer is not responsible for damage or injury caused by incorrect assembly or use. - Page 3 Size up Your Mounting Surface UUUUHHH ?!? 0.8 in. — 2.6 in. Unsure? DESKTOP — THICKNESS Contact The Echogear Pros: 1-855-428-2490 www.echogear.com Power up! Grab These Tools from Your arsenal BOnus Loot! FREE Inside Every Box Yo Hands Refreshment Pump...
- Page 4 Why? Because we like to help and it’s our passion to provide authentic service. We won’t leave you hanging, no matter what. Our U.S. based Echogear Pros answer the phone in all days ending in Y. That means availability to try and stump our expert staff 7 days a week.
- Page 5 Here's your Loadout WARNINGS: DON'T ALLOW CHILDREN TO FEED ON CONTENTS AND NEVER USE DAMAGED GOODS! ► This product contains small items that are a choking hazard if swallowed. ► Before you start assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer;...
- Page 6 Gear FOR Level 2 4 Screws 4 Spacers M4 X 12mm 2.5 mm 4 Screws 4 Spacers M4 X 30mm 5 mm 4 Spacers 22 mm Gear FOR Level 3 2 Cable Straps...
- Page 7 Level 1 Lock It Down! Assemble Clamp and Mount to Desk STAGE 1: Insert Knob into Mount and Attach Clamp...
- Page 8 STAGE 2: Secure Clamp to Surface USE HEX KEY TO SECURELY CLAMP IT DOWN.
- Page 9 STAGE 3: Adjust Arm to Desired Height ADJUST THE TIP: to LOOSEN ARM HEIGHT BEFORE tension MONITOR IS ATTACHED. OTHERWISE IT'S A TWO PERSON JOB. to TIGHTEN tension...
- Page 10 Level 2 Make The DROP! Attach Monitor to Mount STAGE 1: Determine Screw Length and Spacer Size NOT NEEDED NEEDED FOR Inset Round Flat Flat Monitor Holes Cables Monitor Monitor Select Spacers (if needed) Long Screw Short Screw Select Screws Bracket Bracket 7/8/9...
- Page 11 STAGE 2: Partially Insert Top Screws into Monitor 7/8/9 Stack as needed...
- Page 12 STAGE 3: Hang Your Monitor with the Top Screws...
- Page 13 STAGE 4: Insert Bottom Screws and Tighten All Four Screws 7/8/9 Stack as IMPORTANT YOU SHOULD TEST THE TENSION needed OF THE ROTATING BRACKET TO ASSURE THE MONITOR MOVES WITH EASE AND STAYS IN POSITION BEFORE TIGHTENING ALL SCREWS. SEE PAGE 18 TO ADJUST BRACKETS TENSION.
- Page 14 Level 3 Control the Melee! STAGE 1: Route Cables and Attach with Straps LEAVE IMPORTANT: ENOUGH SLACK IN THE CABLES TO ASSURE THE MONITOR AND ARMS MOVE WITH EASE.
- Page 15 STAGE 2: Snap in Plastic Sheet to Disguise Cables "U R A BOSS" Top View...
- Page 16 Bonus Level! Adjustments /Modifiers Vertical Position - Adjust Mounting Bar Up and Down to LOOSEN tension to TIGHTEN tension...
- Page 17 Horizontal Position - Adjust Monitors Left or Right WARNING: MONITOR MUST REMAIN OVER DESK SURFACE. Top View Desk Desk...
- Page 18 Tilt & Level - Tilt and Turn Monitor 360 WARNING: MONITOR MUST REMAIN OVER DESK SURFACE. IF MONITOR DOES NOT MOVE WITH EASE OR WILL NOT LOCK INTO DESIRED POSTION: Remove the monitor. Turn the screw on the tension bracket either counter-clockwise (loosen) or clockwise (tighten) .
- Page 19 How to remove Mount from Monitor and Surface 1. Remove Cables 2. Remove 3. Remove Mount Monitor...
- Page 20 ©2019 Legrand AV Inc. All Rights Reserved. ECHOGEAR is a Legrand AV Inc. brand and a registered trademark owned by Legrand. Legrand AV Inc. • 6436 City West Parkway • Eden Prairie, MN 55344 USA...