FORM FIT HD 20S 04 Manual

FORM FIT
HOOD PROTECTOR
Toyota Echo Hatchback 2004-

Thank you for purchasing a form fit hood protector.

Care Instructions

Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.

Hardware Kit

x 6
x 5 x 6

Tools Required

Installation Instruction

1. Be sure that the hood is clean and dry inside and out. Release the hood, but do not open it.
2. Install all five (5) bumpons as shown in Illustration #1. Attention: The bumpons must be installed
on the hood not the protector!!!! If the bumpons are installed on the protector, they will wear
through the paint.
3. Peel and fold the anti-abrasion film pads in half over the leading edge of the hood underneath each
of the holes in the protector. See Illustration # 2.
4. Push a "C" clip over each of the anti-abrasion film pads on the edge of the hood. Tighten a # 6 x
3/8" screw through the protector and into each of the clips – Note: The screws will tighten quickly –
do not over tighten. See Illustration # 2.
5. Make sure the "C" clips are all fully seated and the protector is centred then tighten a # 4 x 3/16"
screw into the bottom of each of the "C" clips. Do not over tighten the screws. See Illustration # 2.
6. On some vehicles it may be necessary to adjust hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.

Illustration # 1: Bumpon Location

Illustration # 2: Clip Configuration – 6 Location
Made in Canada
# 6 x 3/8'' Screws # 4 x 3/16'' Screws
x 6 x 6
# #
2 1
13"
13"
8"
4-1/2"
1" 5-1/2"
FORM FIT
HD 20S 04 Toyota Echo Hatchback 2004-
Thank you for purchasing a form fit hood protector.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.
Hardware Kit
x 5
Tools Required
Installation Instruction
1. Be sure that the hood is clean and dry inside and out. Release the hood, but do not open it.
2. Install all five (5) bumpons as shown in Illustration #1. Attention: The bumpons must be installed
on the hood not the protector!!!! If the bumpons are installed on the protector, they will wear
through the paint.
3. Peel and fold the anti-abrasion film pads in half over the leading edge of the hood underneath each
of the holes in the protector. See Illustration # 2.
4. Push a "C" clip over each of the anti-abrasion film pads on the edge of the hood. Tighten a # 6 x
3/8" screw through the protector and into each of the clips – Note: The screws will tighten quickly –
do not over tighten. See Illustration # 2.
5. Make sure the "C" clips are all fully seated and the protector is centred then tighten a # 4 x 3/16"
screw into the bottom of each of the "C" clips. Do not over tighten the screws. See Illustration # 2.
6. On some vehicles it may be necessary to adjust hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Illustration # 1: Bumpon Location
Illustration # 2: Clip Configuration – 6 Location
Rev0.031112 Made in Canada
HOOD PROTECTOR
# 6 x 3/8'' Screws
x 6 x 6 x 6
#
2
13" 13"
8"
1" 5-1/2"
HD 20S 04
# 4 x 3/16'' Screws
x 6
#
1
4-1/2"
Rev0.031112