Star TSP100IIIBI Easy Setup Manual

Easy Setup Guide

Introduction

This manual explains the TSP100IIIBI installation procedure and the procedure for connecting
it to a tablet, PC, or other device. For the Windows driver installation procedure, or if the
connection does not succeed, refer to the TSP100IIIBI online manual.

Check the Supplied Accessories

Power Cable* Paper Roll Guide
TSP100III
Paper Roll

Set Up the Printer

1

Inserting a Paper Roll

Insert a paper roll in the direction shown in
the illustration.
Push the cover opening lever  and then

open the rear cover .
2
1
Pull the end of the paper out straight
push down both sides of the printer cover to

When using a paper roll with 58 mm width,
install the supplied paper guide on the close  .
printer.
3
To change the paper width, the memory
switch must be set. Refer to the online
manual for details.
3

Prepare the Utility

iOS* / Android
* iPad / iPhone / iPod touch
By using the TSP100III Utility, it is possible to easily
TSP100III Utility
connect to and configure a tablet (pairing), and
Download
perform an operation test.
- Connecting using the TSP100III Utility
(Recommended)

For the remaining procedure, follow the Utility
instructions. Step 4 is not required.
www.star-m.jp/
- Connecting without using the TSP100III Utility
tsp100iii-app.html
 Proceed to Step 4.
online manual
TSP100IIIBI
www.star-m.jp/
tsp100iiibi-oml.html
If any of the package contents are missing or damaged, contact the dealer where the
product was purchased.
*Accessories vary depending on the region where the printer was purchased.
This Manual
Easy Setup Guide Safety Instructions Holder Plate
Switch Cover Rubber Feet Screws(2)
2

Turn ON the Main Unit

Power
Connect the included power cable to the inlet
on the back side of the TSP100III
the plug of the power cable to the outlet
2
RST

, and
Turn on the power to the TSP100III
check the LED (blue) to light up
4
O
OF
F I
ON
3
Windows
Download the Windows drivers and utility here.
futurePRNT・
After connecting (pairing) in Step 4, use this when
installing the drivers. Windows Driver

The Windows drivers are included in futurePRNT.
When futurePRNT is used, the printer settings
can be configured and an operation test can be
performed.
 When using a version other than Windows10,
www.star-m.jp/
refer to the TSP 100IIIBI online manual to
tsp100iii-wsw.html
follow the later procedure.
4

Connecting a tablet or PC to the printer (pairing)

TSP100IIIBI

The device name displayed during pairing varies depending on the product. It can be checked from the [Dev Name] that is printed when printer
self-printing is performed (power is turned ON while depressing the FEED button).
Windows10
Open SETTINGS  , select [Devices] -
[Bluetooth].
Turn on Bluetooth.
Select the displayed device name (TSP100-
XXXXX), click or tap [Pair].
 . Connect
 "Ready to pair" is displayed when the

.
printer is available for printing.
Turn on Bluetooth.
When "Paired" is displayed, pairing is
completed.
1
 , and

.
4
 After a few moments, "Driver is unavailable"
will be displayed, however pairing is
completed.

Before using the printer

In order to strengthen security and prevent unauthorized
access from devices other than the connected tablet or PC,
it is recommended that the following setting changes be
made after the pairing connection is completed.
Download
① Open the TSP100III Utility, and select [Setting] -
[Bluetooth Settings], then change the [New Pairing
Permission] setting from ON to OFF.
② Tap or click [Apply].
iPad, iPhone, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Android is a trademark of Google Inc. Windows is a registered trademark of Microsoft
Corporation. The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc.
For more information please visit our FAQ site at: http://www.starmicronics.com/support/faq.aspx
iPad / iPhone / iPod touch
Open the tablet settings screen and select Open the tablet settings screen and select
Bluetooth. Bluetooth.
Turn on Bluetooth.
Turn on Bluetooth.
Select the displayed device name (TSP100-
Select the displayed device name (TSP100-
XXXXX).
XXXXX).
When the device name is displayed under
When "Connected" is displayed, pairing is "Paired devices", pairing is completed.
completed.
For customers using iPad / iPhone / iPod touch
TSP100IIIBI includes an Auto Connection function because the TSP100III is always used in a
1-to-1 connection with an iPad or other iOS tablet.
When the Auto Connection function is used, because the TSP100III connects automatically
to the iOS tablet that it was most recently connected to when it reconnects after a
connection was interrupted, it is not necessary to perform manual connection again. This
can also prevent connections from any tablet other than the connected iOS tablet.
To disable this function, select TSP100III Utility [Setting] - [Bluetooth Settings], and change
the [Auto Connection] setting to OFF. Then tap [Apply].
Copyright © 2016 Star Micronics Co., Ltd. 80877711
Android