Star TSP100IV Easy Setup Manual

80878781
Easy Setup Guide
Introduction
This document explains the setup procedure for the TSP100IV.
For further instructions, please refer to the TSP100IV online manual. Please read
the instructions before using the printer. You can also see FAQ from the QR code
on the inside of the printer.
What's Included
If contents are missing or damaged, please contact the reseller that sold you
the printer.
*accessories vary depending on the region where the printer was purchased.
TSP143IV-UE Power Cable* LAN Cable
1
Connecting a Tablet or PC
Connect an appropriate cable to the connector on the printer according to your
operating environment.
1
USB-A
Android
Communication and Recharge
You will need: USB cable included with the printer.
2
®
USB-C
Windows, Mac, Linux
Communication
You will need: USB cable included with the printer.
3
Wired LAN
Communication
You will need: LAN cable included with the printer.
ⓘ When using a USB cable that is available commercially or that came with a
smartphone or tablet, perform thorough operation verification.
For the owners of other companies' trademarks mentioned in this document,see Trademarks in our website (https://www.star-m.jp/eng/trademarks.html).
TSP100IV online manual
FAQ
Paper Roll Rubber Safety
USB Cable Guide Feet Instructions
Plug for the printer
Windows Android
LAN USB-C USB-A
3 2 1
Plug for the printer
Plug for the printer
2
Inserting a Paper Roll
TSP100IV
Push the cover opening lever

open the printer cover .
2
1
ⓘ When using a paper roll with 58 mm
width, install the supplied paper
guide into the printer.
This Sheet
Easy Setup
To change the paper width, the
Guide
memory switch must be set. Refer to
the online manual for details.
4
Preparing/setting up the configuration app
Use the configuration app to set up the
printer from a tablet or PC.
Scan the QR code on the right side or search
the app to access the download site.
When using Android/iOS
Star Quick Setup Utility
 Install [ Star Quick Setup Utility ].
 Open the configuration utility, and
select [ Start Guide (Initial Settings) ] -
[ Search Printer ].

Follow the instructions of the utility to
connect and set up a tablet.
ⓘ
For a wired LAN connection, use the
tablet that is connected to the same
network as the TSP100IV.
 Once a static IP address is assigned, IP address changes through the DHCP server will
not occur, so the specified connection destination device can be used continuously
once set.
ⓘ Driver download site for Mac / Linux environment. (https://www.star-m.jp/supportsite-wsw.html)
 and then Insert a paper roll in the direction shown in
the illustration  .
Pull the end of the paper out straight  ,
and push down both sides of the printer
cover to close  .
Configuration app
download site
When using Windows
Star Windows Software
 Download [ Star Windows Software ].
 Extract the downloaded software and
execute "Setup.exe".

Follow the wizard instructions and
complete software installation.
ⓘ
The Windows driver is included in the
Star Windows Software.
The Star Windows Software can be
used to configure the printer settings
and perform an operation test.
3
Turning on the Main
Unit Power
Connect the included power cable to the
inlet on the back side of the printer  .
Connect the plug of the power cable to the
outlet  .
Turn on the power to the printer  , and

check the blue LED lights up .
Sign up for Star Micronics
Cloud Services
FREE services are available if you register
TSP100IV with Star Micronics Cloud Services.
Digital Journal,
Printed
Promotion,
Service site
and more ！
Registration
site
 Connect the printer to the internet.
(See "Wired LAN" in Step 1 "Connecting a
Tablet or PC")
 Scan the QR code from a smartphone or
tablet to access the registration site for
"Star Micronics Cloud Services".
 Follow the procedures to register the printer
with "Star Micronics Cloud Services" to start
using the services.
ⓘ Please refer to the above Service site for
available countries.
Copyright 2023 Star Micronics Co., Ltd.