Download Print this page

Rowlinson Garden Products SHPOT Assembly Instructions Manual

Potting store

Advertisement

Quick Links

Before assembly
We recommend that time is taken to read the
instructions before starting assembly, then
follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
Check all components prior to assembly
This product should be assembled by no
less than two people.
Never attempt to erect the assembly in
high winds.
Drill components where indicated.
Some of the components may have sharp
edges wear protective work gloves while
handling components.
x 2
Drill
Gloves
Recommended tools
for assembly
Cross head screw driver
Hammer
Sharp knife
Drill
3mm diameter drill bit
6mm diameter drill bit
Spirit level
Silicon sealant
Step ladder
prop
No.
Components
1
Floor panel
2
Angled floor panel
3
Small back wall panel
(1890x570mm)
4
Small side wall panel
(1890x526mm)
5
Large wall panel
(1890x1174mm)
6
Door panel
7
Right-hand window panel
8
Left-hand window panel
9
Window panel
(Opening window)
10
Apex panel
11
Inside roof capping
(170x2145mm)
12
Roof block
(90x54x2100mm)
13
Left-hand rear roof panel
14
Right-hand rear roof panel
15
Mid roof panel
16
Left-hand glazed roof panel
17
Right-hand glazed roof panel
18
Triangular glazed roof panels
19
Roof felt roll (4m)
20
Roof felt roll (2m)
21
Outside roof capping
(170x2210mm)
22
Acorn finial
23
Apex bargeboards
24
Roof felt to glass panel c/strip
(35x12x1090mm)
25
Angled roof coverstrips
(12x35x1160mm)
26
Left glazed roof bargeboard
27
Right glazed roof bargeboard
28
Triangular roof panel bargeboards
29
Door rebate strip
(35x12x1718mm)
30
Door
31
Corner/joint coverstrips
(48x12x1890mm)
32
Angled corner coverstrips
(12x35x1910mm)
33
Potting table
34
Side potting table
35
Potting table legs
(29x35x740mm)
36
Large window glazing
(750x655mm)
37
Small window glazing
(580x255mm)
38
Large window beading
(12x30x728mm)
39
Large window beading
(12x30x657mm)
40
Small window beading
(15x15x257mm)
41
Small window beading
(15x15x555mm)
42
Roof support rails
Potting Store
Assembly Instructions
No.
43
Special finial
44
T-hinge (254mm)
45
Turn button
46
Pad bolt
47
Metal L-brackets
48
50mm coach bolts
49
6mm washers
50
6mm nuts
51
63mm screws
Qty.
52
50mm screws
2
53
40mm screws
1
54
25mm screws
1
55
22mm screws
2
56
30mm nails
2
57
25mm nails
1
58
10mm felt nails
1
1
3
1
1
1
1
1
2
23
24
1
1
3
1
1
1
1
2
2
3
5
1
(35x12x765mm)
31
1
(35x12x765mm)
3
2
1
7
4
1
2
4
5
5
4
10
10
10
10
2
fixing Kit
43
10
42
3
45
46
44
29
30
1
6
Qty.
1
3
1
1
Footprint
4
4
4
4
31
115
22
41
6
69
120
80
22
21
41
12
11
40
14
13
15
16
34
33
35
2
English SS291B
2955mm
20
19
37
39
7
36
38
27
17
18
26
28
25
32
9
8

Advertisement

loading
Need help?

Need help?

Do you have a question about the SHPOT and is the answer not in the manual?

Questions and answers

Summary of Contents for Rowlinson Garden Products SHPOT

  • Page 1 Potting Store English SS291B Assembly Instructions Before assembly • We recommend that time is taken to read the instructions before starting assembly, then follow the easy step by step guide. The instruction sheet is only a guide to the assembly. Certain items may not be shown to scale.
  • Page 2: Important Note

    If the building is to sit on soil or grass it MUST be erected on pressure treated wooden 50mm x 50mm or similar bearers (These are not supplied in the kit). Rowlinson Garden Products recommend using pressure treated bearers with all buildings on any type of base. 2. Wall panels Position the 570mm wide wall panel and a large wall panel on the floor as shown.
  • Page 3 4. Roof part 1 Build the two large roof sections using the four solid roof panels by joining the panel frames together, ensure the frames are flush with each other and secure using 2 x 50mm screws for each panel join. Assemble the roof centre block with the internal roof capping, have the block sitting central on the cap except at the flat end where the two components should be flush with each other.
  • Page 4 7. Roof part 4 Check the whole roof is sitting correctly and adjust if necessary. From the inside of the potting store, secure the solid roof panels to the apex panel using 2 x 50mm screws for each half of the roof then secure the solid roof panels and left and right-handed glazed panels to the roof block assembly using 6 x 63mm screws each side. Fix the glazed panels down to the wall panels using 2 x 50mm screws per panel, screw through the roof panel frame into the top of the window panels.
  • Page 5 10. Roof coverstrips Under the flap of roof felt that overlaps the glazed panels, add a good bead of silicon. Drill four pilot holes evenly spaced along the length of each roof felt to glazed panel coverstrips. Align over the join of the solid roof panel and glazed panel, tuck under the roof capping and secure using 4 x 25mm screws. Drill four pilot holes evenly spaced along the length of each angled roof coverstrip.
  • Page 6 If the building is to sit on soil or grass it MUST be erected on pressure treated wooden 50mm x 50mm or similar bearers (These are not supplied in the kit). Rowlinson Garden Products recommend using pressure treated bearers with all buildings on any type of base.