Summary of Contents for Ovislink AirLive BU-3026-IVS
Page 1
BU-3026-IVS People Counting Guide Version 1.0...
Page 2
BU-3026-IVS People Counting Setup Guide BU-3026-IVS People Counting Guide 1. Overview The BU-3026-IVS has built-in video analytic function for object counting. It is a standalone function built into the camera’s firmware without the need for external software or device. The object counting function can be used to count people or cars. This guide will focus on using BU-3026-IVS’s “Object Counting”...
BU-3026-IVS People Counting Setup Guide 2. Hardware Installation Guidelines It is recommended to have at least 3 meter of vertical clearance (from floor to ceiling) for best performance. The followings are basic installation guidelines to get the best people counting results. However, the people counting function can still work in less than ideal conditions.
BU-3026-IVS People Counting Setup Guide 3. Camera Configuration 3.1 Finding camera using AirLive IP Wizard The IPCAM’s default IP address is 192.168.1.100,but this address can change when there is DHCP server (router) in your network. Therefore, please install AirLive IP Wizard to find your camera.
Page 5
“admin” for username and “airlive” for password. 5. After entering the correct username and password. You will enter the camera’s web configuration page. When prompted to install “Media Control” from “OvisLink Corp”, please select “Yes” to install. 3.2 Enable Camera’s Video Analytic Function Please use Internet Explorer as the default browser.
Page 6
BU-3026-IVS People Counting Setup Guide 2. Click on “Video” on the left menu bar and select “enable” Intelligent Video Analytics. 3.3 Setting Resolution and Frame Rate On the video page, it is important to set the resolution and frame rate correctly. Please remember to click on “Apply”...
Page 7
BU-3026-IVS People Counting Setup Guide 3.4 Configure Object Counting Function Please go to “Video Analytics” menu and select “Object Counting” Below is the main page for Object Counting.
BU-3026-IVS People Counting Setup Guide Zone Area Click to enlarge video window Zone Settings Please remember to press “Apply” after change settings, otherwise the settings won’t take effect. The first step is to set the zones according to your environment. The controls are separated in Zone Area and Zone Settings as indicated above.
Page 9
BU-3026-IVS People Counting Setup Guide Transform Mode: In this mode, you can freely change the shape of the zones to fit your installation site. Click in side the zones to activate edit mode Click and hold the change points to change the shape of the zones Click and hold inside...
Page 10
BU-3026-IVS People Counting Setup Guide ※ Please extend the length of the moving path as long as possible. The length of the moving path is longer. The length of the moving path is too short. ※ If the moving direction is from Zone 1 to Zone 2, user can set bigger Zone 1 to increase the accuracy.
Page 11
BU-3026-IVS People Counting Setup Guide On the Zone Area, two windows label “Max Size” and “Min Size” will appear. Minimum Object Size Maximum Object Size Click inside the small box to change the size Click on either “Min. Size” or “Max. Size” window to change the size of the maximum and minimum objects.
Page 12
BU-3026-IVS People Counting Setup Guide Other Important Settings Detect : Please choose “People” Sensitivity: “Moderate to High” is the recommended settings Counting Result Overlay: Please “enable” this setting. Enable this setting will display the counting result on screen. Counting Results ...
BU-3026-IVS People Counting Setup Guide Statistic Chart Display: When enabled, it will show the counting result in a statistic graph. It is not recommended to turn on this function as it might use a lot of CPU resource which can influence counting performance. If you use this function, please remember to turn it off after finish using it.
Page 14
BU-3026-IVS People Counting Setup Guide 4. Go to “Video Analytics” and “Object Counting”. Change Interval to 10 minutes and quantity to “100”. Then press “Apply” button to save settings. 5. Now, please click on “Set Event Action”. Click on “Add”. Then the following screen will appear.
Page 15
BU-3026-IVS People Counting Setup Guide 4. Retrieve Counting Data You can retrieve the counting results using one of the methods below: Export data from camera’s web interface manually. Let camera send the daily counting report automatically to remote FTP or Samba Server.
Page 16
BU-3026-IVS People Counting Setup Guide Camera Auto Send Counting Report The camera will automatically send counting report to remote FTP or File Server. This function provides great advantage for large installations because data can be uploaded via internet to a centralized server. In addition, there is no need to configure the server when there is a new camera installation.
Page 17
BU-3026-IVS People Counting Setup Guide Configuration Steps: Please go to the “Video Analytics”->”Object Counting” configuration page. The Statistic Record page is on the lower right side. Now check the “Statistic Record” checkbox and fill in the information...
Page 18
BU-3026-IVS People Counting Setup Guide Check the “Statistic Record” box Export Mode: select “Auto” Statistic Period: please choose the report format you prefer By minute: the record file will show the number of occurrence in each minute By hour: the record file will show the number of occurrence every hour. This is the recommended format to use.
Page 19
BU-3026-IVS People Counting Setup Guide <parameter>=<val Value Description ue> action=<string> export mode Which records of IVS function will be exported. fd=Face Detection oc=Object Counting period Which records of period will be selected. 0=Minutely 1=Hourly 2=Daily begin month-day%20hour:min Search time begins,%20 is the html character code of space, 10-21%2012:31 month-day%20hour:min...