Advertisement
Quick Links
Advertisement
Related Manuals for Ovislink Air Live BC-5010-IVS
Summary of Contents for Ovislink Air Live BC-5010-IVS
- Page 1 BC-5010-IVS Face Detection Guide Version 1.0...
- Page 2 BC-5010-IVS Face Detection Setup Guide BC‐5010‐IVS Face Detection Guide 1. Overview The BC-5010-IVS has built-in video analytic function for Face Detection function. It is a standalone function built into the camera’s firmware without the need for external software or device. The Face Detection function can be used to detect and count any person walks by or stays in the detected area.
-
Page 3: Hardware Installation Guidelines
BC-5010-IVS Face Detection Setup Guide 2. Hardware Installation Guidelines It is recommended to have at least 2.5 meter of vertical clearance (from surface to camera) for best performance. The followings are basic installation guidelines for best face detection results. However, the face detection function can still work in less than ideal conditions. 1. - Page 4 BC-5010-IVS Face Detection Setup Guide 3. Avoid the light of surrounding is too dark or too bright. 4. Make sure the position of the camera is right in front of the people. Note: The minimum distance is for reference only. This number is tested base on ACC-MPL-2812 v2 with 2.8mm Focal Length.
-
Page 5: Camera Configuration
“admin” for username and “airlive” for password. 5. After entering the correct username and password. You will enter the camera’s web configuration page. When prompted to install “Media Control” from “OvisLink Corp”, please select “Yes” to install. 3.2 Enable Camera’s Video Analytic function Please use Internet Explorer as the default browser. - Page 6 BC-5010-IVS Face Detection Setup Guide 1. Click on “Configurations” on left menu bar 2. Click on “Video” on the left menu bar and select “enable” Intelligent Video Analytics. 3.3 Setting Resolution and Frame Rate On the video page, it is important to set the resolution and frame rate correctly. Please remember to click on “Apply”...
- Page 7 BC-5010-IVS Face Detection Setup Guide 3.4 Configure Face Detection Function Please go to “Video Analytics” menu and select “Face Detection”...
- Page 8 BC-5010-IVS Face Detection Setup Guide Below is the main page for face detection. Event Settings Zone Area Please remember to press “Apply” after change settings, otherwise the settings won’t take effect. The first step is to calibrate the minimum face size. People’s faces are must bigger than the minimum face size;...
- Page 9 BC-5010-IVS Face Detection Setup Guide On the Zone Area, one window will appear. Compare to the person’s face. When the face is bigger than the window, the face will be marked by a rectangle mark.
- Page 10 BC-5010-IVS Face Detection Setup Guide If the face is smaller than the window, the rectangle mark will not appear on the person’s face. Other Important Settings Sensitivity: Adjust sensitivity 0~100%, the higher sensitivity means more precisely and detailed face detection. Delay between each event: To avoid the events are triggered continuously, the setting can delay the each event follow the setting of time.
- Page 11 BC-5010-IVS Face Detection Setup Guide Face Enhancement: Enable this function for more accuracy. Image Capture: When camera detects faces, camera can send image or video to Samba server or SD Card. Statistic Records: Please enable this item. We recommend choose “hourly” which can report the number of counting in each hour for up to 30 days.
-
Page 12: Event Action
BC-5010-IVS Face Detection Setup Guide Event Action The camera’s Face Detection function not only can detect the human faces, but also can perform certain action when event conditions are met. For example, it can be set if the number of face detected exceeds the maximum 10 or the total amount 15 in the last 30 seconds, it will send an email to the operator or trigger the digital output. - Page 13 BC-5010-IVS Face Detection Setup Guide 4. Go to “Video Analytics” and “Face Detection”. Change Interval to 10 minutes and quantity to “100”. Then press “Apply” button to save settings. 5. Now, please click on “Set Event Action”. Click on “Add”. Then the following screen will appear.
- Page 14 BC-5010-IVS Face Detection Setup Guide 4. Retrieve Counting Data You can retrieve the counting results using one of the method below: Export data from camera’s web interface manually. Let camera send the daily or hourly report to remote FTP or Samba Server. This function is under development, please write to tech@airlive.com to inquire about this...
- Page 15 BC-5010-IVS Face Detection Setup Guide CGI Command to Export Statistic Records Note: This requires administrator access (administrator authorization). Method: Get Syntax: http ://<servername>/cgi/admin/va_trigger.cgi?action=<value> [&<parameter>=<value>...] with the following parameters and value <parameter>=<val Value Description ue> action=<string> export mode Which records of IVS function will be exported.
- Page 16 BC-5010-IVS Face Detection Setup Guide month-day%20hour:min search time ends, %20 is the html character code of space, 10-21%2012:31 Example: Export daily face detection statistics records from Jan. 1 to Dec. 31 http://myserver/cgi/admin/va_trigger.cgi?action=export&mode=fd&period=2&begin =1-1%200:0&end=12-31%2023:59 return: Succeed HTTP/1.1 200 OK Content-Type: text/csv Content-Length: 40 Connection: keep-alive Content-Disposition: attachment;...