Panel Edit Parameters - Yamaha CS2x Owner's Manual

Panel Edit
Parameters
There are numerous parameters available in the panel edit matrix
of menus. In Performance mode, all you have to do is set the
EDIT PARAMETER ROTARY switch to the menu you want, then
press the [UP/DOWN] button directly below the name of the
parameter you want to edit. In Multi Play or Utility modes, the
position of the EDIT PARAMETER ROTARY switch doesn't matter
because there is only one menu of parameters available for each.
Edit Parameter Rotary Switch
ARPEGGIATOR PERFORM
TEMPO SUB
TYPE
DIVIDE
P BEND MW
RANGE PMOD FMOD
TUNE NOTE
NOTE DETUNE LIMIT
SFT LOW
AEG
ATK DCY SUS
TIME TIME LEVEL
FEG
ATK DCY SUS
TIME TIME LEVEL
BANK PROGRAM VOLUME
DEMO
PERFORMANCE MULTI
STORE UTILITY
SYSTEM
MASTER KBD VEL
TRANS
TUNE CURVE
Parameter Value [UP/DOWN] Buttons
Simply pressing any [UP/DOWN] button once will activate Edit
mode and display the name of the corresponding parameter in
the LCD screen, along with the current setting. There are three
ways to change the parameter value setting:
1. Press or hold the [ ] area of the [UP/DOWN] button to
increase values, or the [ ] area to decrease values.
2. Enter the number of the value you want using the NUMERIC
KEYPAD, followed by [ENTER] (for negative values, press [–]
before entering the number).
3. Turn the ASSING 1/DATA knob left or right to change the
values when the knob is designated as a DATA ENTRY
function.
EFFECT PERFORM
LEVEL CHO VARI NAME
REV VARI VARI
COMMON
TYPE TYPE TYPE PARAM DATA
PORTA
FC ASSIGN1
CUTOFF FMOD CUTOFF VARI SWITCH TIME PARAM
EF
VEL ASSIGN 2
LIMIT LIMIT LIMIT OFFSET DEPTH PARAM DATA
HIGH LOW HIGH
LFO
REL AMOD PMOD FMOD WAVE SPEED PHASE
LAYER
TIME INIT
PEG
REL INIT ATK ATK DCY REL REL
TIME LEVEL TIME LEVEL TIME TIME LEVEL
EFFECT FILTER POLY
PAN REV CHO VARI CUTOFF REZ MONO
SEND SEND SEND
MIDI ASSIGN
VEL TRANS RCV DEVICE LOCAL BULK CTRL UTILITY
FIX
CH CH NO DUMP NO
Following is a description of the types of parameters available for
editing:
COMMON Available in Performance mode only, the COMMON
parameters in the Common Edit 1 and 2 menus apply to the
entire currently selected Performance. Except for the PORTA
SWITCH setting, it doesn't matter which Layer is currently
selected, since common parameters apply to all Layer voices
equally. Changes to COMMON parameter settings will remain in
effect as long as the current Performance is selected, but will be
lost if you select a different Performance before performing a
Performance store operation. (page 43.)
LAYER Available in Performance mode only, the LAYER
parameters in the Layer Edit 1, 2, 3 and 4 menus affect only the
currently selected Layer of the currently selected Performance.
Changes to LAYER parameter settings will remain in effect as long
as the current Performance is selected, but will be lost if you
select a different Performance before executing a Performance
store operation. (page 47.)
MULTI Available in Multi Play mode only, the MULTI parameters
include voice, effect, and others which apply to the currently
selected Part. There is memory space for a single set of MULTI
parameter settings. Changes to the MULTI parameter settings will
remain in effect as long as you remain in Multi mode, but will be
lost if you switch into Performance mode before performing a
Multi store operation. (page 58.)
UTILITY Available in Utility mode only, the UTILITY parameters
consist of system, MIDI and type of data assignment (for the
SOUND CONTROL knobs) which affect the CS2x as a whole.
These settings will remain in effect regardless of whether you
switch to Performance or Multi Play mode. (page 61.)
20