Related Manuals for Epson S5U1C31001L1200
Summary of Contents for Epson S5U1C31001L1200
- Page 1 CMOS 32-BIT SINGLE CHIP MICROCONTROLLER S5U1C31001L1200 (Bridge Board Ver. 2) Manual Rev.1.0...
- Page 2 Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products.
-
Page 3: Table Of Contents
Appendix 1. Circuit Configuration Example to Eliminate External Power Supply for Target Board ....................6 Appendix 2. Application to Multi-Programmer ...............7 A2.1 How to Change Jumper Setting .................... 7 A2.2 ENVPP Signal ......................... 7 Revision History.......................8 Seiko Epson Corporation S5U1C31001L1200 (Bridge Board Ver. 2) Manual (Rev.1.0) -
Page 4: Overview
1. Overview Overview The S5U1C31001L1200 (Bridge Board Ver. 2) is an adapter board which is inserted between general-purpose debug probe (e.g. IAR I-jet or SEGGER J-Link) and a target board when debugging an S1C13 Family MCU. 1.1 Function Outputs and controls V voltage (+7.5 V). -
Page 5: Connection Examples
Figure 2.1 Connection Diagram when J-Link is Used When I-jet is used Connect the I-jet to the 20-pin legacy connector on the S5U1C31001L1200 (Bridge Board Ver. 2) using the pitch conversion adapter (ARM-20) that comes with the I-jet. 10-pin user target cable... -
Page 6: Name And Function Of Each Part
Set to OFF (Open) when the MCU's power voltage booster is used. * The jumpers are set as shown in the “Setting for debugging” column at factory shipment. Seiko Epson Corporation S5U1C31001L1200 (Bridge Board Ver. 2) Manual (Rev.1.0) -
Page 7: Connectors
Serial wire clock input – – N.C. – – N.C. nRESET Target MCU reset – – N.C. P (I) DC +5 V input Figure 4.1 20-pin Legacy Connector (J1) Pin Assignment Seiko Epson Corporation S5U1C31001L1200 (Bridge Board Ver. 2) Manual (Rev.1.0) -
Page 8: 10-Pin User Target Connector (J2)
Target MCU reset VTref Reference voltage of the target MCU P (O) DC +5 V power voltage output ENVPP control signal input Figure 4.2 10-pin User Target Connector (J2) Pin Assignment Seiko Epson Corporation S5U1C31001L1200 (Bridge Board Ver. 2) Manual (Rev.1.0) -
Page 9: Appendix 1. Circuit Configuration Example To Eliminate External Power Supply For Target Board
Supply for Target Board The S5U1C31001L1200 (Bridge Board Ver. 2) can supply +5 V and +3 V fixed power only to the target board. If the target board requires another voltage to operate, it must be externally supplied to the target board. -
Page 10: Appendix 2. Application To Multi-Programmer
Appendix 2. Application to Multi-Programmer Appendix 2. Application to Multi-Programmer The S5U1C31001L1200 (Bridge Board Ver. 2) allows multi-programming using a J-Link. Multi-programming (*1) uses the +5 V power output of the J-Link as the V ON/OFF control signal. This does not allow use of the +5 V as the power source of this board. -
Page 11: Revision History
Revision History Revision History Attachment-1 Rev. No. Date Page Category Contents Rev 1.0 2017/07/25 New establishment Seiko Epson Corporation S5U1C31001L1200 (Bridge Board Ver. 2) Manual (Rev.1.0) - Page 12 Phone: +49-89-14005-0 FAX: +49-89-14005-110 Keyuan South RD(Shenzhen bay), Nanshan District, Shenzhen 518054, CHINA Phone: +86-10-3299-0588 FAX: +86-10-3299-0560 EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD.