1. Manuals
  2. Brands
  3. Raven Manuals
  4. Autopilot System
  5. SmarTrax MD
  6. Installation manual

Raven SmarTrax MD Installation Manual

For new holland windrower hw300, hw320, and hw340 series
Hide thumbs Also See for SmarTrax MD:
Table of Contents

Advertisement

Quick Links

Download this manual
New Holland Windrower HW300,
HW320, and HW340 Series SmarTrax™
MD Installation Manual
P/N 016-5030-081 Rev. A
12/15
E26948
Copyright 2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SmarTrax MD and is the answer not in the manual?

Questions and answers

Related Manuals for Raven SmarTrax MD

Summary of Contents for Raven SmarTrax MD

  • Page 1 New Holland Windrower HW300, HW320, and HW340 Series SmarTrax™ MD Installation Manual P/N 016-5030-081 Rev. A 12/15 E26948 Copyright 2015...

  • Page 2: Table Of Contents

    Chapter 1 Node and Wiring Installation ..........1 Install the SmarTrax MD Node ....................1 Node Mounting Locations ....................1 Mount the SmarTrax MD Node .................... 1 Install the Foot Switch ....................... 2 Install the Node Harness ......................3 Install the Chassis Cable ......................
  • Page 3 Table of Contents New Holland Windrower HW300, HW320, and HW340 Series SmarTrax™ MD Installation Manual...

  • Page 4: Important Safety Information

    Raven dealer for support. • Follow all safety labels affixed to the SmarTrax MD system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact your local Raven dealer.

  • Page 5: Electrical Safety

    Chapter 1 CAUTION Electrical Safety • Always verify that the power leads are connected to the correct polarity as marked. Reversing the power leads could cause severe damage to the equipment. • Ensure that the power cable is the last cable to be connected. New Holland Windrower HW300, HW320, and HW340 Series SmarTrax™...

  • Page 6: Introduction

    Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax MD system for the first time, at the start of the season, or when moving the SmarTrax MD system to another machine: •...

  • Page 7: Point Of Reference

    Software and manual updates are available on the Raven Applied Technology website: http://www.ravenhelp.com At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual.

  • Page 8: Kit Contents

    Kit Contents This section contains a list of the components that are included in the SmarTrax MD kit. Before beginning the system installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 9 Chapter 2 SmarTrax MD Installation Kit (P/N 117-5030-081) TABLE 1. Picture Item Description Part Number Qty. Nut - 3/8”-16 Zinc Flanged Lock 312-1001-167 Nut - #10-24 Wing 312-3000-013 Washer - 0.265” ID x 0.505” OD x 0.060” 313-2300-120 Thick Tape - 3” Double-Sided...

  • Page 10: Mechanical Drive Installation

    M echanical Drive CHAPTER C h a p t e r 1 Installation Disassemble the Mechanical Drive Spline Assembly Spline Assembly Disassembled FIGURE 1. Washer Female Spline Adapter Male Spline Adapter Bolts Locate the 7/8” 36 tooth spline adapter assembly (P/N 063-4001-024). Disassemble the spine adapter assembly as shown in Figure 1 above.
  • Page 11 Chapter 1 Steering Wheel Cap FIGURE 2. Remove the cap from the center of the steering wheel. Steering Wheel Nut to be Removed FIGURE 3. Steering Wheel Nut Remove the nut used to secure the steering wheel to the steering column. Steering Wheel Removed FIGURE 4.

  • Page 12: Install The Anti-Rotation Bracket

    Mechanical Drive Installation Install the Anti-Rotation Bracket Console Cover Screws Removed FIGURE 5. Locate and remove the screws used to secure the console cover. Anti-Rotation Bracket Installed FIGURE 6. Position the holes in the anti-rotation bracket (P/N 107-4001-053) over the holes in the console cover. Secure the anti-rotation bracket on the console cover using the screws removed in step 1.

  • Page 13: Install The Spline And Ring Gear Assemblies

    Chapter 1 Bearing Installed FIGURE 7. #10-24 x 3/4” UNC Carriage Bolts (P/N 311-0069-082) 1/2” Plastic Flanged Bearing (P/N 325-0000-036) Install the 1/2” plastic flanged bearing (P/N 325-0000-036) on the anti-rotation bracket using two #10-24 x 3/4” carriage bolts (P/N 311-0069-082) and two #10-24 wing nuts (P/N 312-3000-013). Install the Spline and Ring Gear Assemblies Female Spline installed on Machine’s Steering Column FIGURE 8.
  • Page 14 Mechanical Drive Installation Ring Gear Assembly Installed FIGURE 9. Place the ring gear assembly (P/N 063-4001-011) over the female spline adapter with the V-ring facing down and the holes in the ring gear aligned with the holes in the female spline adapter. Male Spline Assembly Positioning FIGURE 10.

  • Page 15: Reinstall The Steering Wheel

    Chapter 1 Reinstall the Steering Wheel Steering Wheel Installed on Ring Gear Assembly FIGURE 12. Nut and Washer from Spline Assembly Steering Wheel Spokes Installed Aligned with Ring Gear Assembly Spokes Align the spokes of the machine’s steering wheel with the spokes on the installed ring gear assembly. Install the steering wheel on the male spline adapter.
  • Page 16 Mechanical Drive Installation Anti-Rotation Pin Installation Locations FIGURE 14. Anti-Rotation Brackets Anti-Rotation Brackets Installed on Right Side of Installed on Left Side of Steering Column Steering Column Determine the anti-rotation pin (P/N 107-4001-004) installation location on the mechanical drive (P/N 063- 4001-010) based on the anti-rotation bracket installation location.
  • Page 17 Chapter 1 Mechanical Drive Installed FIGURE 16. Install the mechanical drive around the installed ring gear assembly, closing it firmly until the latch on the casing is securely locked. Tighten all nuts to ensure the anti-rotation bracket assembly is installed securely. New Holland Windrower HW300, HW320, and HW340 Series SmarTrax™...

  • Page 18: Node And Wiring Installation

    N ode and Wiring CHAPTER C h a p t e r 1 Installation Install the SmarTrax MD Node Node Mounting Locations Node Mounting FIGURE 1. Direction Arrows Any two arrows must be parallel with level ground Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: •...

  • Page 19: Install The Foot Switch

    Secure the node mounting bracket to the floor using two #10-16 x 3/4” zinc self-tapping screws (P/N 310- 1002-073) or 3” double-sided tape (P/N 332-0000-019). Install the SmarTrax MD node (P/N 063-4001-013) on the node mounting bracket using three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-167).

  • Page 20: Install The Node Harness

    Node and Wiring Installation Route the foot switch cable to the node mounting location. Install the Node Harness Node Harness Installed on SmarTrax Node FIGURE 4. Install the two large, rectangular connectors of the node harness (P/N 115-4001-157) into the correct ports of the node (P/N 063-4001-013), tightening the bolts on the connectors to secure the connections.

  • Page 21: Install The Chassis Cable

    Loop and tie-off the REMOTE SWITCH cable connection, securing it with plastic cable ties as necessary. Note: The REMOTE SWITCH connector is not used in the SmarTrax MD system. Ensure the cable is secured away from moving parts and heat sources.
  • Page 22 Installing the Spline and Ring Gear Assemblies 4 Reinstalling the Steering Wheel 6 Removing the Steering Wheel 1 Node and Wiring Installation Installing the Chassis Cable - SmarTrax MD-Only Systems 4 Installing the Foot Switch 2 Installing the Node Harness 3...
  • Page 23 Índice New Holland Windrower HW300, HW320, and HW340 Series SmarTrax™ MD Installation Manual...

Table of Contents