Advertisement
Installation Requirements
Environment
Keep monitor away from heat sources, extreme cold, and humidity. Avoid direct sunlight, dust, and
equipment that generates magnetic fields.
Ventilation
Do not install in an enclosure, unless proper ventilation is provided, Do not block slots and openings in
the cabinet.
Power cable
Route to ensure nothing potentially damaging comes in contact with the cable. Refrain from creating
small-radius cable coils.
Installation and Configuration
1. Install the mounting bracket's VESA plate and wall plate. For detailed instructions, refer to the MVQ-V200-MTPLT
Mounting Bracket Installation Guide.
2. Run the power cable to source, and then use the supplied butt splice connectors to connect wires as follows:
•
24 V converter's input red wire to vehicle's ACC power via 7.5 A fuse. WARNING: Do not connect directly to battery
power.
•
24 V converter's input black wire to ground.
3. Connect the power pigtail's wires as follows:
•
Red wire to 24 V converter's output yellow via 5 A fuse
•
Black wire to 24 V converter's output black .
4. Secure the HDMI cable connector to the HDMI input's preinstalled lock using the supplied cable tie, and cut off the tie's
end.
5. Turn on the monitor by pressing the power button
solid while the monitor is powered up. See the Monitor Controls section for LED colors explanation.
6. Press the Mode button to display the input source menu, cycle through the menu options by pressing the Up and Down
buttons until the desired option is highlighted, and then press Left or Right button to confirm your selection.
7. Access the on-screen display (OSD) configuration menu by pressing the Menu button.
8. Review the OSD Menu Overview, Monitor Controls and OSD Menu Options sections that follow for explanation of
available options, and then proceed with selecting your settings.
NOTE: Complete configuration before mounting
To deter tampering, control buttons are located on the back panel, and are not easily accessible once the monitor
is mounted. Therefore, check the image and perform the required configuration prior to mounting.
9. Mount the monitor to the wall. For detailed instructions, refer to the MVQ-V200-MTPLT Mounting Bracket Installation
Guide.
OSD Menu Overview
Picture
Top level menu
† Screen and Auto Adjust options are available only for a VGA video source.
on the back panel. The power indicator LED illuminates and stays
Sound
Option
Function
Monitor Controls (Back panel)
Control Description
Power
•
Toggle the monitor power on or off.
•
The power indicator LED illuminates green when the monitor is powered up.
Mode
•
Cycle through video source input options: VGA, HDMI, AV1, AV2.
•
In menus: navigate up and down through menu items.
Menu
•
Open or close the menu.
•
With a setting selected: close the setting and re-display the menu.
Down
•
On main screen: decrease the volume.
•
In menus: navigate to the next menu option.
Up
•
On main screen: increase the volume.
•
In menus: navigate to the previous menu option.
•
With a setting selected: decrease its value.
Left
•
In menus: navigate to the previous option in top menu.
•
With a setting selected: decrease its value.
Right
•
In menus: navigate to the next option in top menu.
•
With a setting selected: increase its value.
OSD Menu Options
Menu Item/Setting
Description
Picture
Picture Mode
Picture preset.
Color Temperature
Color profile: Cool is more bluish,
while Warm tends toward yellow.
Aspect Ratio
Ratio of the on-screen image width
to the image height.
Option
OSD Language
Interface language.
OSD Duration
Time OSD menu remains displayed. Off/60/45/30/15/10/5 (seconds)
Transparent
Transparency of OSD menu panel.
OSD Reset
Default settings restored.
Function
Color range
Limited vs. full range of colors.
Noise Reduction
Reduction of artifacts that degrade
image quality.
Screen
Manual image adjustment.
†
Auto Adjust
Automatic image adjustment.
†
Software Update (USB) Firmware update from USB.
Sound (sound settings are not used with this monitor)
Balance
Audio balance setting.
Sound Mode
Audio preset.
Auto Volume
Audio volume preset.
IR Remote
Not used
Values or Options
Additional User Options
Setting
User/Standard/Soft/Vivid
Contrast
Brightness
Color
Tint
Sharpness
User/Warm/Medium/Cool
4:3/16:9/Zoom1/Zoom2/Just Scan/Panorama/ Point to
Point/Auto
English/简体中文
High/Middle/Low/Off
N/A
On/Off
High/Middle/Low/Off
Horizontal Pos.
Vertical Pos.
SIze
Phase
-50 — +50
Standard/User/Sports/Movie
Bass
Treble
On/Off
Values
0-100
0-100
0-100
0-100
0-100
0-100
0-100
0-100
0-100
0-100
0-100
Advertisement
