Pentair Hydromatic Novus 4000 Installation And Service Manual
  1. Manuals
  2. Brands
  3. Pentair Manuals
  4. Control Unit
  5. Hydromatic Novus 4000
  6. Installation and service manual
Pentair Hydromatic Novus 4000 Installation And Service Manual

Pentair Hydromatic Novus 4000 Installation And Service Manual

Standard electrical controls
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NOVUS 4000
STANDARD ELECTRICAL
CONTROLS
INSTALLATION AND SERVICE MANUAL
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # H-03-518 | Part # 5625-518-1 | © 2012 Pentair Pump Group, Inc. | 11/02/12

Advertisement

Table of Contents
loading

Related Manuals for Pentair Hydromatic Novus 4000

Summary of Contents for Pentair Hydromatic Novus 4000

  • Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # H-03-518 | Part # 5625-518-1 | © 2012 Pentair Pump Group, Inc. | 11/02/12...

  • Page 2: General Information

    connected to any sensor that has Adjustments are provided for General a 4-20 Ma. output. When used both scale and offset. to control level in a tank or well, Information • Inputs for pump seal leak the input is usually connected to a sensors pump over...

  • Page 3: Pump Down Operation

    with the state and local codes. If WARNING: Before handling c. Connect all the float control you are in doubt about anything, these pumps and controls, leads or 4-20mA leads to the contact a qualified electrician. always disconnect the power appropriate panel terminals.
  • Page 4 current lead pump is displayed is zero then the backup system Time At on the right side of the top line of is disabled. If the high float is the display. When the lead pump activated, and backup is enabled, Setpoint starts the liquid level should begin and the pumps are not already...
  • Page 5 For example, assume that the test on and off setpoints and there are pumps alternate. When either of is enabled with a START TEST setpoints for high and low alarm. the two large pumps is on the time of 15 seconds. When a pump Unlike pump down the pump up small one is turned off.
  • Page 6 3. HIGH LAMP When the controller is in one When the controller is in one of the two menus this button is of the menus these operators This red lamp signals that the used to increment the current are used to change the value level is above the high setpoint.

  • Page 7: Configuration Menu

    1. Depress the MENU button and memory EEPROM which will not correct then press the UP/YES hold it until the first setpoint lose its contents when powered button to save it, or press the appears on the bottom line of down. This is done every time DOWN/NO button to continue the display.
  • Page 8 the current setpoint time. This seal fail inputs. Use the UP the alarm will auto reset if the and DOWN buttons to select alarm condition clears. parameter is the minimum time a setpoint condition must between the options available. TEMP NORM LATCH – The options are: be continually met for the In this mode the temp fail...

  • Page 9: Start-Up Operation

    1 6. The display should say or 20 Ma. Use the procedure phase pumps, check black ALTERNATE XX where XX in steps 3 and 4 above to make pump lead. is the current setting. This any changes and depress the 9. Check operation of start relay, parameter determines what MENU/NEXT button which if supplied on single phase...
  • Page 10 in the Hand mode with the Moisture can cause damage to Temperature H-O-A switch. electrical com ponents. Check door gasket for prop er seal. Fail Inputs 3. Check pump run light(s) by run ning pump(s) in Hand 1 0. Check labels to verify they mode.

  • Page 11: Pump Specifications

    6. Check contactor coil one, measure voltage with Pump re sis tance. recorder on a 24 hour basis. Specifications B. Pump does not run in 4. Make sure the transducer Auto position. is locat ed away from any turbu lence. General specifications: 1. Is water level in the sys tem high enough to...
  • Page 12 a. Label the leads and the but as the ca pacitor Typical ter m i n als 1, 2, and 3 becomes charged Motor Resistance respectively. (by the meter), it will Winding Leads Reading return to a read ing of b.
  • Page 13 THIS PAGE INTENTIONALLY LEFT BLANK...
  • Page 14 THIS PAGE INTENTIONALLY LEFT BLANK...
  • Page 15 THIS PAGE INTENTIONALLY LEFT BLANK...

  • Page 16: Standard Limited Warranty

    Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.

Table of Contents